diff --git "a/4_Woodworking/narration_transcript_woodworking.json" "b/4_Woodworking/narration_transcript_woodworking.json" new file mode 100644--- /dev/null +++ "b/4_Woodworking/narration_transcript_woodworking.json" @@ -0,0 +1,247 @@ +[ + { + "category": "woodworking", + "name": "User_1_411_1810_Carpentry_480.mp4", + "transcript": " I'm going to remove this thing and then I'm going to fit it with new screws after I finish the rasping process so I'm going to attach the clamp first of all and clamp it properly and tightly make sure that it's nice and tight and to take the tool and i'm going to search for the drill bit here Taking size 2, which should fit quite well. Attaching the battery. The battery is good. Opening up the chuck and the tool. locking the chuck and reversing it for unscrewing now I'm going to put on the gloves for safety reasons and carefully start unscrewing the Look carefully. first screw is out um taking out the second screw okay the second screw is also out so i'm going to place this to the side now and grab the rasping tool it should be here and start just leveling this thing Let's create a chamfer okay for chamfering on this side i'm going to remove this and adjust this and fit this here and fit it in and okay now that this is done I'm going to adjust the block and flip this to work on this side and perform the same operation and I am going to try and unclamp it and clamp it okay i don't think this is tight enough so i'm going to loosen it and adjust the grip and try and clamp again and this time i think it is tight enough check the block okay And adjust the clamp again. this looks quite level to me scraping out the unsmooth ends ok after this I can reverse this and adjust this again and attach the screws back on on the original location put on the gloves and attach this first screw before doing that to adjust this and now once again attach the screw now that is this much in i'm going to attach the second one because i think it is slightly easier okay this is tight and then i'm going to tighten this as well okay so the assembly looks quite thorough so i'm going to unclamp this and inspect the setup okay this is the surface is quite smooth and the assembly is attached rigidly to the block after this being done I'm going to put this to the side check off the gloves and also detach the drill bit check off the battery place check off the place it back and also place the tool back put the battery on for charging okay return the tools back to their and start cleaning up the place Place it back and the process is now complete." + }, + { + "category": "woodworking", + "name": "User_1_User_15_411_2310_1_480.mp4", + "transcript": " so we have to take this bracket and attach it onto here so first if we let's say just try with a regular screwdriver you'll notice that this is just too tight so it won't properly come out it's also lot of effort so to deal with this let's just put on gloves first so that yeah okay okay Then we are going to attach this clamp onto this Attach it onto the metal plate frame here on the bottom you can extend it by pressing on this and bring it onto here make sure that this is tight and it doesn't move so in your case it is moving so we need to remove it or maybe reposition it let's say like this so the problem is that this is the maximum extension of the clamp so we can tighten this a bit and try again Okay, I'm just losing it. Let's try again. the block is now rigid enough so use the drill machine so first just run the battery properly and check that the battery level is sufficient so that you can work with it okay yeah we need the correct bit so let's just try and find one i think size one or size two should fit getting around a bit and lock it in Okay, now press this switch that it is going in reverse so that you can unscrew with this. Yeah, perfect. So now let's just start with one of the screws and hold it and move it slowly. I would recommend to put it on once so that it moves a bit slowly. Same for the other screw. Alright, so now we need to prepare this side for the operation. So just lightly unclamp this so that you can't move it enough. before we begin with the process we can just place the bit the bracket and mark the hole so in the bracket one of the sides is shorter so the shorter side should align with the let's say exact height of the wooden block so just confirm that it does and yeah okay so we're going to attach the bracket here at the left corner so i'm just going to mark with my pencil roughly where i think the two holes should be and you can also do that before we begin with the drilling process we need to however make this surface a little more chamfered so we are going to use a rasping tool and just at 45 degrees just slightly make the edges not so sharp You can use the flatter edge which might make it easier. Since we want to make the whole side we'll also need to unclamp and do it on the other side which is right now hidden. You only need to move it a little bit. for tightening it. You're not in the middle, I think, anymore. and then also just make the surface also flat on this side okay we'll also need to flip the block and do this on the remaining side Okay, and then also the remaining part of the bottom side. Just move the clamp slightly. okay so we'll put the rasping tool to the side and then once again orient the block so that we have the bracket edge marked with the pencil on the left and clamp the tool again I think your clamping surface is quite small, so to be careful. OK, it's not moving now. What we can just try and do is see if we are able to attach the screws onto this, first of all, or if the wood wooden surface is just too hard. So without the bracket, we can just try making the hole in the marked pencil location. Or I think first it's a good idea to make a small dent in the surface. so with this tool i'm just going to make a small dent um location i want to drill the hole okay just try it yourself so the holes here okay so now let's just do a small test to see first move the switch to this side so that it actually is drilling in and let's just try to see if think your location is just too close to the plate but I think it should still fit it should still fit no I think it will fit so no I mean yeah you will have to take it out eventually yeah so for my block the resistance is just too high so I'm going to drill a small hole at that location first i don't think you need to do it but if you if you do then we can just keep this tool for later let's just try with the normal operation again but this time with the bracket I think for me pressing it very lightly works like but if I press it too hard You want to exchange the machine and see if that makes a difference? Okay, so I think that machine is more powerful at the moment. So you can finish your second hole and finish mine. I think it's pretty much done I think you know you're finished when you cannot easily move it or yeah so I think that is pretty good let's finish this the toughest one Thank you. I think the problem is that the wooden block that I have is just too rigid so I'm gonna have to drill a bigger hole for them okay But you might also face this issue in the future. So it's good to see different challenges. I think it's also harder on this side because this is going against the grain whereas on this side it's going... Yeah. Let's exchange a little bit. and then the second screw I believe it's also pretty rigid so i think then you can just unclamp this the clamping tool to the side and inspects if the bracket has been fit correctly and also if you can just hold it with the bracket then you know that it is pretty tight and pretty solid what we can also do is just clean the block any residual wooden things and Put the wind block to the side. Just start touching this from your side. to the part below Let's throw this in the trash. What we're going to do next is start putting the tools away. So the hammer and the chisel will go here. The raskin tools also here. the screwdriver was from cabinet tools and then just start detaching the tool a little bit also take off the battery of the glass and the last thing that we need to do is put the battery on for charging so you can plug this in and then you just slide it in onto this okay now it's charging okay the operation is complete" + }, + { + "category": "woodworking", + "name": "User_1_user_16_411_1810_3_480.mp4", + "transcript": " we're going to remove the plate from this and if you notice it is tied quite securely so we can't move it so let's try with the drilling machine then so the first thing that we're going to do is open this up you can open it by clicking on this on your side and once it is open place it like this and clamp it in place so it is tight enough and then once it is here you can clamp it to this metal rod yeah make sure it is held tightly in place it doesn't move and the block also doesn't move yes just make sure that the block doesn't move okay perfect then we're going to try with the drilling machine so take the drill bit out and select the one that suits the best with the profile of the balls that we have here i have picked number two but if you think number three is fine you can also pick that and first just open this up there it is yeah quite enough so that the drill bit can fit and then tighten it up yeah I think once you hear the click should be tightly in place yeah okay so make sure that this button is pressed on this side so that it is ready for unscrewing and then carefully hold your hand here it is a better idea to put on the gloves yes so okay thank you then i'm going to put it on here securely and carefully place the carpet here and then it should detach and do the same on the other end Yes. Okay. Good. Okay. Yes. And on this side. Carefully apply pressure to it and then it will come off. Okay. Perfect. So I'm going to finish this. and it's done operation is complete and just put the glass to the side and remove the drill bit remove the battery and put it on for charging exactly the process is complete" + }, + { + "category": "woodworking", + "name": "User_1_User_16_411_1810_4_480.mp4", + "transcript": " we're going to attach this metal plate on this block and the way you align this is so you can see that one of the ends is shorter so the shorter end is going to be attached like this yeah exactly yeah like this okay so the first thing that we can do is firstly you should just uh clean the workspace just uh grab that cloth and also have this uh handy and just or you can also use the brush both are fine just make sure that you also have the thing below the board clean throw this in the trash okay good then we can start by attaching this on this end yes and fix it properly in place make sure that the assembly is no longer moving OK, now what we can do is just mark with a pencil where we intend to fix this and exactly know where we should drill the holes. Yes, I'm just going to mark this little. I'm just marking the boundary of where I can reach. I know what I'm targeting. I'm going to do this. okay now we're going to to guide the holes in we're going to hammer a few small holes but first we should wear some gloves Okay, so grab your glove and also the chisel and gently at the top where the first hole is going to be just hammer in a small dent. I see that my clamp is already a little loose, so I'm going to adjust it and tighten it again. Okay. cool now let's take the drilling machine first and if you haven't done so already attach the battery and then we're going to take size 2 cross-head drill bit and attach it onto the machine so first uh should just size two should fit first just uh open up the process yeah open up the drill bit and then lock it in place hear a click and then yeah it is pretty much good so make sure that this is turned on this side so that it is drilling in okay and then what we can do is either attach this and drill it or hold it in place and wait until the drilling is done but what you can then do is very carefully hold it in place and don't apply too much power just start very small and then when it's already done you can remove your hand from there and just let it go in do the same for the other end once clamp is on clamp so i think we should Adjust it and tighten it again. Yeah, adjust it now. No, adjust it this first. Wait. Now we can close it. I hope it's not. The drill bit is quite powerful and quite hard. wait so you cannot adjust this because this will not go because of the misalignment okay so move it out okay and now we can adjust this again now you can fasten it okay then wait a minute maybe put it out and use okay let's pull it out put it out yeah pull it out I'm gonna also pull it out for now Okay. And we could try is, uh, maybe and try without the bar to see if i can drill it turn it on and the problem we are facing is that the the wooden let's say yeah the word that is that we are compressing is not able to come outside because of that it's not able to let's say exactly find the right place to compress so what we can do is see if we can get some drill bits here the drilling operation okay in that case what we could try is filling these larger holes in here for future use but they are definitely yeah far larger than what we need them so we're going to do it all the way but just a little bit same process one way around turn it inside yeah No, it's going inside. Okay, maybe this drill bit isn't sharp enough. Okay let's try with yours. Turn it on. Yes. Okay so let's finish yours first. I'm gonna change that real bit loosen this and let's place it here turn it on Correcting this. Okay. okay so the operation is complete and the same would happen on this side but the assembly is the block is too rigid Bye. what we can do is detach this and attach this on the other end we can clamp this here easier and fix it properly and in this case I'm going to align this on this end and first of all fix this in place yeah i'm gonna blend this with the hole just a minute make sure it's on and Okay, before we fix this, I think it's a good idea to attach this first. okay this is held in place so now i'm going to unplug this and place this here place the wooden block carefully here detach the drill bit place it back I'm going to attach my battery for charge I'm going to start cleaning the desk okay and once the thing is relatively clear you can then turn the trash okay the end of the operation check off the gloves the operation is now complete" + }, + { + "category": "woodworking", + "name": "User_2_414_0611_1_480.mp4", + "transcript": " so the first thing is putting on the safety gear I will start with the vest putting the power bank out to be able to wear the vest properly zipping up the jacket and then putting on the working gloves now we'll inspect the wooden block and the bracket i have to remove this bracket it is loosely attached and then I'm gonna attach it to the new block here so I will test if I can remove this with a screwdriver and it works Okay, I successfully removed the two screws. I can leave the bracket here. Okay, so now I can put this away. this and take the new block inspect it okay so i will attach the bracket on the side here now okay so this is the side i want to attach the bracket to i will climb the block on the table and make sure that it is attached to the table. i'm going to use this part of the table then and then attach this here tightening the clamp make sure the block can move anywhere And now I want to attach the bracket like this. I want it to be a few centimeters away from the edge. Two centimeters would be good. Exactly like this. outside layers and the two drilling holes like this. Before I attach the bracket I'm gonna rasp the four edges of my block and smoothen it. Also the corners. pick up the screw that fell down so now the four edges and corners are smoothened What I also can do is remove the surface. Okay, so I'm gonna remove the clamp again to also smoothen the other corners and edges. Now I can clamp the block to the table again. Okay, it's tight again. it's a bit movable tighten it a bit more this okay then i'm gonna I'm gonna make some dents at the marked spots for the screws. Just to make sure that when I screw it in, it will stay in place. So here. This is alright I think. And this too. Let's test it out. Yep. now I can take out the drilling machine here and have to see where the battery for this is located it is here i can check if there's still enough battery for working it is Now I will need the correct drill bit for the cross-headed screws. This is good. Oh, and I also need the bit holder piece. Just put it in like this. Make sure it's tight. I'm going to open this up and attach the holder in the middle. Like this. I'll place my bracket here and then gently start screwing in my screws while securing the position of the bracket Just make sure that it's tight. I need to apply a bit more force to make them go in. Now both screws are tightened. Let's see if the bracket is still loose and movable. It's not so the bracket was attached successfully. Now we can assemble the drill again. toolbox and I'm gonna charge the drill batteries Here's some plugs. I can place it here to charge it. Now I'm just going to clean up a bit. and also remove the clamp make sure the block is clean and clean the table from remaining wood chips and dust now I can remove my safety gear And now I'm finished. I would just put on the cloth to hide the working space" + }, + { + "category": "woodworking", + "name": "User_2_User_1_411_1110_1_480.mp4", + "transcript": " okay so first we can put on the working gloves and then each of us can take one clamp and clamp it onto the table and screw this part tight to the table next thing is loosen this and adjust this part so we can put the wooden block over the table and then tighten it by pressing the lever yeah it should be pretty like horizontal next thing is we can open this up to make space for the blocks and then we can place the blocks right between the clamp and then screw this in to tighten to make the boom block tight. Okay, it seems like mine is a bit too big and this is too short. We can check the other block here. This one's also a bit big. I mean, you can switch. Maybe yours is different. okay for me not even the shorter block fits hmm but i can also place it in loosely and then i have to hold it with my hands now the screw is too short with this thing okay so it just won't fit no Mm-hmm." + }, + { + "category": "woodworking", + "name": "User_2_User_1_411_1110_2_480.mp4", + "transcript": " okay so before working we should put on some working gloves and then each of us can take a clamp to clamp a wooden block tight to the table um maybe we should clamp it sideways so we have um space here to work open it and then put it all the way back on top and then for like tightening Just rotate this clockwise. Yeah. um next thing we could we should mark the two holes um if we want to take those brackets and yeah so my block is a bit shorter but that is not a problem so we should just oh right yeah so we can just take the pencil and mark the edges of the bracket and also where the holds are going. so the first thing we should do is sawing into the marked edges of the bracket but the best way to do it is to rotate this again so we can saw from the top so just loosen the clamp again yeah like this so break it to sear and we can put the clamp like this and then just tighten it up again okay then you can just take your saw and try to align it with your marked line and then start sawing just Start slowly and like... seems like my saw is a bit dull but there should be one saw here so there are two more bigger one and a smaller one This one is not much better. No, this one works a bit better. or do we need more? no we don't need to make it deeper this is enough what we can do now is take those things and two hammers and try to get rid of this piece I hope it works like that i'm not sure um so they're not here i think they have the other toolbox because those are too pointy to get rid of this Okay, so I think those things are not sufficient for this. But for this time we can just drill it right here. We have the brackets here. But now we can take hammer and this thing to mark the holes for our screws. Yep. that the holes are correctly aligned here. Mhm. the first hole is not really captured so we could have one more here okay now they're aligned now they're aligned okay then we can take Each of us needs two smaller screws but with a cross as a head. And the first thing we can do is assemble our drill machines with the needed drill bits. At first we need to open this up. Therefore I press this button. It goes backwards and I hold on to the black part of the drill and then just press the button here to open it up. then insert the drill bit and then we have to change the direction again for tightening and then do the same thing again until it's tight yeah so now we can take our screws and put them in the holes we prepared and then just screw them in with the machine and try applying some force on the drill machines. like this and then we can move on to the second screw yeah make sure that both screws are tightened all the way okay and then try moving the bracket if it's not moving them and successfully attached The next thing we can do is smoothen the edges of our wooden block with the rasp. Just angle it in a 45 degree angle. and just move it up and down and then do the whole thing on the other side too Maybe try using the flattened end. okay so now all edges are smoothened and the last operation for our wooden block is just smoothen the surface where we have the bracket on yeah so now um we successfully attached or break it to the block and then we can remove the clamp just untighten the handle and then bring the two pieces back together and then i can place them on the trolley now we have the blocks here and can clean up our working space we can take the saw and the rasp and the hammer and put them all into our trolley The rasps were in the drawer. Then we can take our drilling machines and disassemble the drill bits. So now we have to press the reverse button again. Hold on to the black part and press the button. Just slightly until it loosens. yeah now we can remove our battery by pressing the button sliding it off and put those in our charging stations this and just slide it on yeah now they're charging you can put the drilling machines on the trolley too take this sandpaper and those pieces and finally now that the table is cleared from tools and objects we can take the brush and just wipe off the remaining wooden chips and we can throw it in the trash bin over here and just place this on the trolley again yeah we're finished with the work and we can take off the gloves" + }, + { + "category": "woodworking", + "name": "User_14_411_2409_1_480.mp4", + "transcript": " So I am going to drill a hole in this wooden block. So first I'm putting on my working gloves. and so i'm also going to attach this clamp to this table Now I'm tightening it from here. So, and now I need to fix this block into this. I also need to tighten it from here. Now I'm going to mark a hole here in order to drill a hole. So for that, I'm going to need this measuring tape and a pencil. So I want to drill a hole here and I'm marking here about four centimeters, I guess. And to start drilling, I need a drill machine. So I cannot find it here. Let me check here. Yeah, I found it. So I think I also need a drill knot or I don't know how to call it. So I'm going to drill a four millimeter hole. So that's why I think I need this one. I also need an extension cord. Plug it in like this. So I'm also going to plug this machine in. Turn it on. So now I'm going to set up my drill machine. I think it's done and I'm ready to drill a hole now. So as I said, I wanted to drill a hole here where I marked. Now I'm going to drill a hole here. i think it looks fine to me okay but i also want to smooth it so for that i'm going to need a sandpaper here now i am smoothing this block Perfect. So now I'm going to remove it to see if I did it correctly. Yeah. So I'm also going to remove this glam. I also need to clean my workspace. For that, I'm going to use this brush to clean wood chips. And I'm going to throw them into trash." + }, + { + "category": "woodworking", + "name": "User_14_414_0602_Woodworking_480.mp4", + "transcript": " So I'm going to polish this wooden box. I put on the gloves. Now I need to empty the box. So before polishing it, I need to clean it first. And the edges look a bit rough. And I also need to smoothen the edges. I'm going to use this sandpaper. So now I am sanding the corners. The sanding is done, now it looks good. I am cleaning the box. And now I'm going to polish the box with this oil. I sprayed some oil on it. And I'm using this cloth to spray it. I also need to polish the edges a bit maybe Now I'm polishing the inside of this box. I need some more oil. I lay the carpet here. So I let it dry, now I'm going to polish the other side of the cover. place always Now it looks good, I guess. And now I let it dry for some time. I take off the glass." + }, + { + "category": "woodworking", + "name": "User_14_414_1102_Woodworking_Shelf_Fail_480.mp4", + "transcript": " so i'm gonna make a shelf i'll be using these wooden bars and these tools a drilling machine and the sandpaper first i need to put on the safety jacket Thank you. Now I'm putting on the gloves. I'm attaching the clamp to the table. Now I am sanding the rough edges. I can also do some rasping. Now I need to flip it over to test the clamp. Now the edges look good I guess. Not too sharp. I remove the clamp I'm turning that off with this kind of paper Now I'm cleaning the wooden bars. Now I'm going to clamp it again. I'm looking for a pencil to mark the holes. I'm also using this measuring tab. I'm marking the position for the holes. So now I'm gonna do these four holes. so that one is broken i'm gonna use the other one i put too much pressure on it Mm-hmm. so i'm gonna mark the other hole Now I want to stick these two bars. First with some glue. I guess I did something wrong. I should have drawn the holes here, not here. that should be the base of the shelf I'm gonna place it like this. First I need to stick these bars with some glue. Should be clamped like this. Now I can stick them together like this. I need to adjust it a bit. Now I'm gonna stick these bars with the screws. I need to change that a little bit. I don't know how to position the bar so I can screw them. So first I'm trying to stick the bars with the glue. Now I'm screwing it in the drilling machine. It's a bit difficult. I can also use these small clamps. I also need to align the bars. Talk. I'm going to take it out. Now I want to try again. I need to tighten it. Um. I should align the bars. Now it looks terrible. this one is done but perfectly i'm gonna do the other one here" + }, + { + "category": "woodworking", + "name": "User_14_414_1712_woodworking_1_480.mp4", + "transcript": " So today I'm going to disassemble this wooden box. I'll be using these screwdrivers. First I want to detach this lid, the cover of the box. So I'm removing the hinges first. And screwing. Thank you. So the hinges are removed successfully, as you can see. And the covers also. I'm gonna put it here. So now I want to remove this blade. so the plate is also removed now I am removing this clasp so there are only two screws here Now I'm gonna remove this part. Just unscrewing. So this one is also removed. another box needs some cleaning so i'm gonna clean it a bit the edges look a bit sharp so i need to smoothen them first here I forgot to remove these hinges. so now i'm cleaning it so i have disassembled the box completely as you can see" + }, + { + "category": "woodworking", + "name": "User_14_414_1712_woodworking_2_480.mp4", + "transcript": " So I want to reassemble this wooden box. And I'm gonna paint the inside of the box a bit. So I want to, I need to wear my, put on my gloves. And I also need to put on my mask. So I'll be using this rag and this band. So I want to paint the inner portion, inner part of the box. So the painting is done. So now I'm going to reassemble it. First I want to attach the cover of the box. so I'm doing the hinges first I'm trying to align the holes So the holes are aligned now. Screwing it. Thank you. It should be here. No. The holes are aligned now, I'm going to screw it. so the outer side is done Thank you. Bye. so the cover is installed successfully and now i can open it and close it easily as you can see so now i'm going to install the clasp Should be here, I guess. Mm hmm. Mm hmm. So the other part is here. Screwing. So now I'm going to install the upper parts. I'm just exploring it. Oh. Mm-hmm. That's working. So now I'm going to install this part here. So this part is also installed successfully. Now this side. So the holes are aligned. Let's clean it in. Mm-hmm. Thank you. So the assembly task is done and the box is ready to be used, as you can see. Now I can open it easily. Thank you." + }, + { + "category": "woodworking", + "name": "User_14_1414_1811_1_480.mp4", + "transcript": " So today I am going to do some woodwork. First I need to put on my jacket and gloves. so i'll be needing some tools and all the tools are here first i need to clamp this wooden block to the table So now I want to do a drill setup because I need a drill machine to attach these metal parts to the wooden block. It's here. So now I'm going to attach these parts here. I'll be using these longer screws. I guess I need 8 screws It should be like this So now I'm going to screw in Oh, good. Thank you. So I guess first I need to draw some holes. Thank you. Thank you. so i'm going to take it out it's a bit crooked So this one is not going in. Okay. Hi. Now I want to attach this one. Hmm. Bye. So now I'm going to attach this part to this, like this. So now I'm going to clamp this wooden block like this. so now i'm going to attach it with three screws here so first i guess i need to draw some holes with a hammer and this so the edges look a bit sharp i guess i'm going to rasp it a bit like this i can also do it with the sandpaper To make it simple. So now I'm going to scroll it in. Okay. Bye. Hi. So this one didn't go in. Did not go in? Yeah. Okay. It's a bit, it's not straight, that's why. Okay, you can check later, but you can finish your work. Yeah, and this one is also not going in. together first and then otherwise it's going to be very shaky so i would recommend you to take this off and let's say we're going to clamp it like this okay rotate it like this and then clamp it I also wanted to take it out but I couldn't this is fit for now so you can leave it you can attach the two and then just leave one side open It's not going in, I guess. This, I think the speed is just somehow very high. so we should definitely do it much slower for example this is on unscrew so that's the problem now it should go and do it slower first you created the drilling holes right yeah here and the second one is going to be here so with this small bit you first you can oh i did it with this hammer and this one i'm going to just tighten this I need to clean this one and same on the other side so we should first maybe measure how much distance there is here for example 2cm and this is also roughly 2cm if you mark that here from this side also 2cm is roughly here The problem is when you're drilling like this, the wood that we drill just gets stuck in the middle. That's why it might be a bit better if you... If this doesn't still work then it might be better if you remove this, clean this wood and then try it again. But I think maybe it works correctly. Try this again. Always make sure that this is on grilling first, otherwise... But yeah, I think this is now good enough. What you can do is the same on this side, but to do this, I think we might just try first, I think. Oh, no. Be a little slow at first. yeah perfect so now this is complete i think i can unclamp this and inspect if the fitting is the two pieces are yeah" + }, + { + "category": "woodworking", + "name": "User_14_1414_1811_2_480.mp4", + "transcript": " So I want to separate these two wooden blocks. So first I need to clamp it. so i'll be using this machine roll machine to take these screws out in order to detach this part Thank you. so now i need to remove these two metal parts and i need to unscrew all the screws This part is removed. So now I'm going to unclamp it. I guess I also need to smolden these holes a bit. So I'm putting everything back. I'm cleaning the wood chips. No, I'm removing the bed. It's charging now. So the task is done and I need to take off my gloves and jacket." + }, + { + "category": "woodworking", + "name": "User_14_User_16_411_1810_1_480.mp4", + "transcript": " to put on working gloves, yeah. so i'll be using this clamp okay i don't know how to fix it so i'm also attaching this clamp Like this? No, not here. Okay. Okay, yeah. Okay. So I'm taking this out. Okay. Yeah. Yeah, this one fits. Maybe you can also have a... Okay, then I'm taking this. which one the the red ones yeah okay and how did you i can do it but just put it inside here yeah and connect to the So how can we remove these screws with this version? Just remove it. Okay, like this, yeah. No, no, no, no. Push it, push it. Okay. Not so tight. Like this. Like what I'm doing, just push it, push it forward. Push it forward, push this forward. Slowly, slowly, slowly. Okay. Just softly put the trigger. Softly. Softer, softer. Because if you are too quick, they will just lose the attachment. So just do it very softly. Like this. That was too quick. You can try without this. So I have removed, this is cool Can you hold it here? Sorry, it's... Push it and slowly. Oh, sorry. No, no, no, don't worry, don't worry. Slowly, I said. because we can see this screw is almost almost unusable right so we can change the new screw like this the bigger size which can be which can be more suitable let's see if that can fit in and fit into this it's a shorter shorter way yeah and they both can fit doesn't matter they don't need to be so long you can fit some shorter this tool this tool and this it's also fitting well yeah and this one is also good was it like this or no no and we can use the same holes here and don't forget to change it How did you do it? Can you show me? No, no, no worries. You can continue with the second one. Don't tighten it too much. Okay, we can continue with the top one. I also need to remove this clamp. I don't know how. It's too tight. should i also remove this no no no It might be here. Yeah, I... Yeah, great. And put this away a little bit. And then throw back into the box. I think there's still something... i think we are missing one school" + }, + { + "category": "woodworking", + "name": "User_14_User_16_414_1202_1_480.mp4", + "transcript": " Yeah, ready. Okay. I need to take it out. Mm-hmm. What's going on with this one? It's stuck. Yeah, it's crooked. I mean, the head is broken. So the head, yeah. Yeah, it's damaged. Which one? This one? No, it's not. It's almost a circle. Maybe we can take it out with the pliers. I need to put on the glass. Thank you. Now I think I can do this. Yeah, that's OK, thank you. First one, I'll put it here. It's going to hold. Okay. maybe try to unscrew this one as well Do we have a hammer here? So taking this out. Or pliers. Clamp it. Now pull it out. Damaged? No. It's not as straight. It's crooked, yeah. Mm-hmm. Yes, it can be out. We can throw it away. Yeah, we can use the other way. Where is the small thing? Here, right? Let me check if we can. This out. It's hard. Good. Put it out. uh we should do some rasping so it's already clamped i think we should So the rasping is done. No, it looks better. No. No? Okay. More detail. In case we use pen, it doesn't hurt our hands. More detail. More detail. More detail. That's enough, I guess. Okay, then after we get off. Should I clean it now? Which one should we use? This one? It's a bit damaged, so I think we should use this one. So now I'm gonna do some rasping. No, I'm sending the rough edges. Okay. This one has also sent it? Yeah. You can put it on that part? Oh, I can send this part. Yeah. I have to look on this part. I'm cleaning the water you. I organize the tools. not take off the gloves and the jacket" + }, + { + "category": "woodworking", + "name": "User_14_User_16_414_1202_2_480.mp4", + "transcript": " Put on the jacket set. Thank you. Yeah. Okay. Yeah. which one should be the base plate okay so if we want to drill a hole connecting these two parts together we have to like this right? yeah so yeah first we should stick them with glue Do we need to mark the position first? I think first we should drill some holes. Yeah. Where's the pencil? Yeah, there's some pencil. 81. No, it's almost 83. 83 82.5 yeah no i'm just yeah we can we can mark a hole here maybe it's already one here so i mean uh how to divide by so uh we have three twenty twenty no we haven't So we are going to drill three holes? Yes, three holes, because one hole is... Yeah, okay. So we divided by four, 20 by each. 20, 40, 60. Yes, we have 20, 40, 60 here. But I don't think it's stable. We need to drill a 10 and 70. And... To be here then. I think we have some extra screws here. Then we can make four. 10, this one, so 30 and 60, right? So, a 30 and 50. 30 and 50. Let it go. . . . Before that. To measure the distance? It's one millimeter. This is also one. This is also one. So this is also one. So this should be right here. . . . . Okay. Okay. Okay." + }, + { + "category": "woodworking", + "name": "User_15_410_2609_1_480.mp4", + "transcript": " Start with this measuring tape by pulling the tape measure out. So the length on this side is eight, almost eight centimeters. So 7.8. So half of that is going to be 3.9. So we have the half mark right here. And then I'm also going to measure it over here. Again, 3.9. I'm going to draw the line. And I'll also do the same in the middle just to have more accuracy. Okay, now we can measure this length, which is 20 centimeters. So I'm going to put the measuring tape along the lines that I just drew. And then at 10, I'll make a line here. And so now this is exactly where I want the hole to go. Right there in the middle of that cross. and I want it to be six millimeters thick so I'm going to choose the drill bit that has a six by it which is going to drill a six millimeter hole and then to put it in the in here I'm going to first turn this black part around to open this hole up so that I can fit the drill bit in and then I'm just gonna close that again and now oh I need a bit more cable Now, if I press this button, it will drill. Okay, perfect. And then I'm going to put on gloves for some extra safety. And then I can use this drill. Am I pointing this drill, but right where I want the hole, I can now This is actually the wrong direction. So I have to put this bit, I have to push in so that it turns the right way around to drill a hole. And I'm just applying light pressure to drill this hole. Okay, now I'm done. i can take it out there we go i'm just gonna remove some of this and now we have a six millimeter hole and i can use some sandpaper which is a grit 80 i believe to just smooth this roughness down a bit and it's gonna grind away all the rough looking spots I'm going to blow on it to get the dust off and also use this file because I want this edge to be like this. So I'm just going to file it down a bit and it has two sides, one that's flat and one that's slightly rounded. I'm going to use the flat side to just give it the same appearance as it has over here. There we go. Okay. And now I will take the drill bit back out by turning this. Okay. So first, if I do this, I have to push this in the middle kind of, and then I can loosen this by going counterclockwise. I can take the drill bit out and I can close it back up again. There we go. Now I can close this because I'm done using it and I can put all these materials here back so that I don't leave a mess on the table. All right, I will also take this with me and the brush to help me clean it up a bit because there is a lot of dust on here that I want gone. there we go now I can untighten this to get the block out and then again there's some dust everywhere so I'm taking that off with this brush also untightening the clamp down here go by going clockwise there we go now I can put this and this back so the clamp and the wooden block I can put that back over here And the brush I still need to get rid of all of this sawdust. I'm just going to use this to clean up by swiping it into the dustpan with my brush. Now that that is all clean, I can also put this back. And then all that's left to do is to detach this electric drill with the cable on it again. There we go. We're also going to take this out. All right. And to make it a bit easier for next time, I'm also going to kind of roll this cable up after I untangle it. There we go. Almost. It's just a knot in here that I'm going to take out and another one. Okay, now it should be untangled and I'm just going to use my hand for this. I'm going to hold it like this and then wrap the cable around my arm so that it doesn't get tangled again. Like so. Okay. And there we go. Now the station is all cleaned up. I can take off my gloves. And we have a nice hole in the middle, a six millimeter hole in the middle of our wooden block." + }, + { + "category": "woodworking", + "name": "User_15_410_2609_2_480.mp4", + "transcript": " Okay, first I'm going to turn on the light because I want to be able to see very well because I want to drill a hole into this wooden block. So for that, I'm going to put this over here and I will take this clamp to actually clamp it down onto the table. So I'm going to put this block here, put on the clamp like so, and then I can move this upper part, this lower part down a little bit like this, and then I can just fasten it by turning it counterclockwise. Here we go. So for tools, I will need the tape measure, this pencil, this wooden file, sandpaper, and the drill bits. I'm going to put them over here. And of course, I will also need the drill. And for the drill, I will need the battery, which I've charged over here. So I can now take that out and plug it in here, like so. And I need gloves. So first I'm actually gonna draw out where I want my hole to be, which I want it to be right here in the middle of this part and this part. So I'm just going to measure. So this hole is at 10 centimeters. So half point would be at five. So I'm gonna put a little line here. And then this length is 18 centimeters. Half of that is nine. I'm going to put a line here and then where these two lines would intersect. So here is where I want my hole to go. And I'm just measuring by pulling this tape measure out. So I want my hole to go right here and I'm going to mark it with an X. And yeah, so now I can put on my gloves. so that I don't hurt my fingers or anything. And since I want it to be a six millimeter hole, this drill bit is too big. So what I can do to change it is just turn this part around by going clockwise until I hear the click and then a little bit more, and that will loosen this mechanism inside so that I can then take this part out and replace it with one from here. And as I said, I want a six millimeter hole. So I'm just going to take this one that says six on it, this drill bit, put it in here and then turn this thing counterclockwise or yeah, to secure this back in to close the mechanism that's inside. until I hear a click. There we go. Now it's inside. By pressing this button, the drill will turn on. If it says zero, it's going to pull out, and if it's on this part, it's going to drill. So now I can take this, and I've marked my hole, and by holding it vertically above and applying light pressure, I can now drill a hole while holding this button. Oh, it's a bit stuck. Again. We're just going to tighten it a bit. There we go. Okay. And now to get it out, I'm just turning the switch over and it'll come straight out. And then it's perfect, but I have a bit of unevenness. So I'm going to use the sandpaper, which has a grit 80 to just get rid of that. to make the whole thing a bit more smooth. And I'm going to blow on it to get the sawdust off. And then as you can see, this side has a nice slanted edge. So I want the same on this side. So I'm going to use this wood file to just file the edge down a little bit with the straight side. To have a nice slanted edge over here as well. There we go. I can put the tape measure, the pencil and the sandpaper and the wood file I can put back to where I got them. And I can grab this dust pan and the brush to just get all of the sawdust off the wooden block. And then I can unclamp it by turning this clockwise. to loosen the clamp. There we go. And I can now put this back as well. And then I just have to change this drill bit because the person that was using it before probably needs this one again. So for that, again, I'm just going to turn it to the right till I hear the click and then a little bit more to loosen it. I can take it out, put it back in its place. Close this and then I'm just going to open it a bit more because this has a thicker diameter or bigger. Put that back in. Then I can close it by going counterclockwise till I hear the click. Here we go. I'm going to put this back. Then I will use the dustpan and the brush to clean up any residue, so any sawdust that's left over. I'm just going to use the brush, especially in these slight edges to get all the sawdust off of the working station. And then I can put this back as well. I can take my gloves off now. And now I'm going to charge this again. So to take off the battery part, I'm going to press this button and I can pull this out. I'm going to put this actually back with the other stuff. and plug this back in. See here's the short side, there's the wide side and I can just plug it in like this. And then if I want to transport it to a different room, I'll just take this out and put that over here as well so that I can transport it back. And that is everything so I can now leave and turn off the light." + }, + { + "category": "woodworking", + "name": "User_15_414_0302_1_480.mp4", + "transcript": " Okay, so today I want to prepare this box for shipping. So first I'm going to put on this safety jacket. For safety and also so that I don't get any stuff on my normal clothes. I'm just going to zip that up. And then I also need some gloves. Okay. So first, in order to make it a bit easier for myself, I'm going to take off the lid and all the stuff inside. And then I want to see if I can take this bottom plate off ideally. So for that, I'm going to use this electric drill and I need to find the correct bit size. So I see this is a star tip. So I think maybe this one. No, that's too big. Um, oops. So maybe this one, which is also too big. And then that's probably just about this one, maybe. Yes, this one's the correct size, so I'm going to place that into the extension, and then I can stick it in here, and then tighten it by turning to the right. And now I can put my glove back on. And if I push this, it should turn to the left, meaning that it will unscrew. So I'm just going to start unscrewing these screws. Okay, and the last one. Let's see if we can take this off. However, I don't think we can because it seems like it's glued, kind of like the rest of this. It's not connected inside. Okay, so I can't actually take this off to make the sanding a bit easier because these edges are a bit sharp. So I'm gonna put all these screws back and so I have to push this in so that it goes in the right direction. And then I'm gonna screw all these screws back in. Okay, and the final one. All right. Okay, so now I can start with the sanding, and so that this doesn't slip around so much, I'm going to actually clamp it to the table using this clamp. Let me open it, there we go. and turn that to the right to tighten it. Maybe open it a little bit so that I can move this a bit more forward like so and then tighten it again. There we go. That should be pretty secure. And first I'm going to go over these surfaces with some sandpaper. So I'm going to choose this one. which I don't know what grid it is. I'm just going to go over everything lightly just to make sure it's smooth. Same over here. Okay, and now I'm going to use this file to just make these edges a bit smoother. So I'm just going to Go like this. On either side, maybe the other side is better. Just to smooth it out. Especially these. That's a lot smoother already. And of course the sides over here as well. And also over here. Okay. And now this side as well, but I'm going to go with this. Oops. Just going to sand it all over. Now this is already pretty smooth. This can definitely be smooth. There we go. Okay, now the other side. I think every surface is smooth here, so I'm just going to unclamp it by turning it to the left. And then we can do this final side, which was covered by the clam. And also just... Okay, so now I'm just going to clean what I just sanded. So for this I'm going to use this and just spray a bit on this rag so that I can then wipe everything down. Okay and now I can turn this around and do the top part and this is kind of hard to clamp so I'm just going to be pretty careful when using this. So first I'm going to start here and just go all around and just rasp all the sharp corners. Actually, I will try to clamp down because it is moving quite a lot. Ah. It has to be clamped here, I think. There we are. Okay. Bye. Okay, now all that's left is this side where the clamp is. So I'm gonna remove the clamp by twisting it to the left. And now I can do this final part. Okay, and I'm also going to sand inside a bit. Using this piece of sandpaper. the sides as well okay also these outer sides And then again, I'm going to use this and the cloth to clean it up. And also to care for the wood a little bit. Okay. Now all that's left to sand is the lid, but first I'm just going to put the stuff to secure the package later back in just so I don't have it lying around like so. And now I can push this back here and take the lid up here. and sand these edges down. So I'm going to hold on to it when I do this. That's two sides. The third. And the fourth side. And I'm also going to just stand down the top a little bit. And now the other side. There we go. And the same thing here. And the last side. Okay, and now again I'm just going to use this cloth to clean it. there we go place that to the side and now i can put the item that i want to ship in here and because of this padding it's going to be hopefully very secure so i'm just going to place this in here and then we place this padding on top And then the lid goes on top of that, like, not like so, like so. Okay. And now, let me clean this up a bit. The screws for the lid are in here. So I'm just going to open that up, dump those in here. We don't need these, nor this, nor this. Okay, let's see what kind of bit we need. So this is actually a cross, so we won't be needing the star tip from here anymore. So I can put that back and then try to find one that fits this. I think this one might work. Yes. Okay, so I can close this back up. Attach this by just pushing it in. Make sure this is in this direction so that it actually screws the screw in. And now I'm going to make sure that this is all aligned. And then I can screw it shut. That's one. Two. Three. And four. And this one here. and this one on the opposite side or the diagonal opposite side there we go now everything should be fine i'm just going to make sure that nothing moves in there now this is ready for shipment and all the edges are nice and smooth so nobody hurts themselves so now i can take these gloves back off i'm just going to take this off and It's probably best if I charge this. So I'm going to put this back in its box down here. And then I can charge this on here. I have to plug that in, of course. There we go. And now I'm just going to clean the top of that a little bit. So I'm going to take this trash can and this brush. And then we can clean up a bit. This area is clean. I can move stuff over here. I'm just gonna brush all the sawdust. There we go. Okay. Now everything is clean. The box is ready for shipment. I can take this jacket off. And that's it." + }, + { + "category": "woodworking", + "name": "User_15_414_0302_2_480.mp4", + "transcript": " okay so today i want to thoroughly clean this box so in order to properly do that i'm going to have to remove all the hardware out here so i'm just going to use open this and then just use the screwdriver to remove everything by turning rotating it to the left oops I'm just going to place the hardware with its screws so that when I go to screw it back on later I won't get confused. Same over here. And I have to lift this up to get to the screws here. Oh. I'm also going to remove this handle. There we go. Same on the other side. Okay, now I can remove these hinges. And now I can remove the lid and remove the hinges from here. So I'm just going to take these first screws and these first screws. Put this over here. And then also remove this hinge. okay and now for the oh i also have to remove this so i'm just going to turn this counterclockwise to take it off there we go and then i can lift this part out oops put that over here now for the cleaning process i am going to put on some gloves okay now for this i'm just gonna use this cleaner with this rag so i'm just gonna spray the cleaner on here and then wipe down the box make sure i get all the edges as well on the other side See, this is why we removed the hardware so that we can also get to these places. Okay, now that the lid is all clean, let's move on to the box. So I'm gonna start with the, well, okay. Start with the outside. Flip it back over. And to the inside as well. Also the top edges. There we go. Now I can put it all back together and because this took kind of long and I want the screws to be secure, I'm actually going to use the electric drill. So for that I'm going to keep my gloves on. And first I'm going to place this back in here so that I can reattach this disc by turning this clockwise. Making sure that's tight. Okay. And now I'm going to actually first attach the hinges back on here. So I'm just going to take this and it goes, let me see how this fits on here. So, like so. I'm going to line that up with these holes. And then I have to find the right drill bit for these screws. I'm just going to take one and see what size. I think this one might be good. Yeah, that's a perfect fit. And I also need the drill bit extension. And I'm just going to place that in here and then tighten it. There we go. And now I can take this, make sure this is pushed in so that it doesn't unscrew the screws. Place my screw. And carefully screw it in. I'm going to place the second hinge over here. Make sure that this is the correct placement actually. Yeah. Okay. All right. Oops. Oops. See, that's fine again. all right okay and now we can attach this to here no i think it's easier if i lay it down like this that way these are properly aligned it's best if i do this one first Okay. Next, I want to attach these latches back on. So for that, I need to... Well, first, let's do these. There it goes. Like this then. Okay. So let's line this up. And then place the screw. Here it is. Same with this one. There we go. Now I think I am gonna just flip this to make it a bit easier for myself maybe. Take these two. Whoops. I have to align this. Now we can already close this. And align this. Place the screw. also close this one and now all that's left to do is to attach the handles on either side so they go on this way so i'm going to attach the bottom two first i think All right, now this is properly secured. I can do the other side. Not to be lying down. Because we can't stand it on the side because of this. Okay, so this is gonna be a little bit trickier. Make sure that these are the same. Okay. So I'm going to have to align this. I think I'm going to do the middle one first. Because that will help it stay in the correct position. Okay. Now I can do the top two. Now if I move this handle to the side, I can access the lower two holes properly. Now I'll move it to the other side. okay now everything is attached let's check that everything's fine the hinges work properly i can close it properly and also lift it up okay now everything's clean reattached i'm gonna take my gloves off i'm also gonna put this away so first i'm gonna take the bit out and then remove the bit extension and i also have to charge this so i'm going to take it off the battery and then place the bits and the drill in here and now i can plug this in here plug it into the wall and now this should be charging okay And now this is properly cleaned and I'm done." + }, + { + "category": "woodworking", + "name": "User_15_414_0611_1_480.mp4", + "transcript": " Okay, so I want to move this bracket from this block to this block, but first I'm going to put on my safety jacket. Whoops. And close that as well. Like that. And I'm also going to put on my gloves. All right. Now I'm going to take a look at this block and see if I can maybe use a screwdriver to take these screws out. So I'm going to try with this one by just turning counterclockwise. It's a bit hard on that one. Let's try this one. Okay, that requires a lot of force. So instead what I'm going to do is use an electric drill probably. So in order to do that, I'm going to take this clamp to clamp the block to the table so that it doesn't move around while I'm working on it. And I'm just going to take this and then attach it here by screwing this part clockwise, I believe. I see the issue. There's a hole here, so it has to actually clamp here. Like this. And then we'll just clamp that there. I'm going to check that it's secure. It's not moving around, so I think we're good. And I'm going to take the electric drill out of its case. Just open these two. And then the ones on the side. Here we go. Now I can take this drill, fit the battery onto it. I'm going to close this and take this and put it on the floor so I have more working space. And now I'm just going to try to find the proper screw bit. Let's open this up. We're going to need this. I think this one might work. So let's, yeah, that's a good fit. I'm going to put this in here. Close this, put it off to the side. Then I can make sure this is in neutral. And then tighten this, I think, this way. like so until it clicks. And now to screw something out, you have to press this part in. Make sure it's unscrewed. And it should screw it out. So I'm going to align it with the screw. And then gently... Maybe it is the other way. No, that's putting it in. to go a bit slower. That should work better. There we go. Now I can just take this screw out and I'll do the same over here. All right, there we go. I've taken this out. I can now unclamp it again. Put this over here. I'm just going to make sure that this is all clean. I'm going to put that over here. Let's take a look at the instructions again. All right. OK, now I'm going to look at this block and then mark the side where I want the bracket to be attached. So I think I want it to be on this side, probably. I'm just going to take a pen. and put an X on here. Now I'm going to clamp it to the table so that I can rasp the edges properly. So to do that, I'm just going to do this, turn this until it's tight, and this doesn't move around anymore, so just a little bit more. There we go. And then I'm going to take this rasp to just file down these edges a bit. that they're a bit more smooth. Also these ones, oh. Be a bit more careful with this. Also on this side. And then I'm going to unclamp it again. so that I can turn the sock around and get the top part. I'm just going to clamp that down once more. And then this side. Okay, now that I've done that, I am just going to Clean this off again. And then I'm going to turn this back around to how I originally wanted it. Clamp it onto here. Just making sure that it's nice and secure. Now I can take a pencil to mark the outline of the bracket of where I want it to go. So right here and right here and then we'll also mark the inner part. Like so. And now this is where I want my screw to go. And this. So I've marked that. Okay, and now. Now I'm going to use. this and a hammer to make some slight indents where I want the holes to go to make it a bit easier later so here and here like that and now We're going to try to screw these in. So I'm just going to take that out like this. And then align it like so. See that they go in. I'm going to do the same here. Now this works relatively easy so I am going to attach this. For that, I am gonna take them out again. So again, just flip that over to go in the other direction. And then I'm gonna put this here, align it there, take my screw, push this out again so it goes in the correct direction, and then screw that back in. There we go. And now the other screw, which goes down here. I'm just going to align this again. So it's at a right angle and then just carefully screw it in. There we go. So I'm just going to check there's no movement, but there isn't. And then Now I've moved the bracket from that block to this block, so I'm done and I can just put everything away again. I'm going to put these. I'm going to put this back up like so. Put that here. I can take this block and I'm just going to check again that it's not moving around but it's not. So I can put this over here. Now I can disassemble this. So in order to do that I'm just going to open this up so I can take this out. Place the screw bit in the correct position and take it out by pushing this down. Then I can just take it, put it back where I got it from, and then also place that back. I'm also gonna charge this battery. So that's gonna go right over here. And that should be charging, I think. Yeah. And then I can also put the electric drill away. So I'm just gonna open this up, put these two pieces back. And you can close this again. And now I think, let's just make sure that this is all clean. There we go. Just put this in the trash. And then I can take off my gloves. This pencil goes over here. And the safety jacket. And now I am done with putting this bracket onto the other wooden block." + }, + { + "category": "woodworking", + "name": "User_15_414_0702_1_480.mp4", + "transcript": " Okay, so today I want to clean this box and also oil the wood a bit to take care of it. So first what I have to do in order to do that is take the hardware off. And for that I'm first going to also put on some gloves. Okay, now I can take all the hardware off. by rotating the screwdriver clockwise. And then I'll just store everything together so I know what belongs to what. Put that over there. Whoops. Where did this... Ah, here I was looking for the screw. And now for the edge protectors at the bottom. So I'm going to very carefully flip the box over. So that I can now take these off by unscrewing the three screws here. Okay, I'm going to carefully flip this back over again. And now I'm also going to take the handles on the sides off. Might as if this will grip. I think the screwdriver might be a bit small, but it's fine. There we go. And the other side as well. Okay, now I've taken that off as well. The only thing left to take off on the outside is these clasps. So in order to do that, first I'm going to close it again so that I can unscrew these tiny screws. Okay, now the other side. Now that we've taken that off I can open it and then empty it. So we have this and for this I'm actually going to get a piece of styrofoam to place it on so that it doesn't get damaged in the process. So first of course I'm going to open Put them off to the side as well. Now I should be able to take this off. by sliding it upwards. And this I'm going to put over here. And then I can take this off. I'm going to place that here. And then take this and this off as well. Let's see if we can take those off. Oh, no. Okay. So now I'm noticing that these edges are a tiny bit sharp, so I'm going to use some sandpaper to just sand them down a little bit. that's a lot better and now I'm going to use this cleaning agent to just clean the whole box I'm gonna use this rag for that as well so I'm just gonna spray some on here and then use that to clean the inside of this box so the lid of the insides. I'm going to close this and also clean the outside. Then I'm going to flip it over and clean the underside as well. Okay, there we go. And now I'm going to open this back up and I'm going to oil the wood. So I'm just going to take one of these papers, take the lid off here, and then just put a tiny bit of oil. on here like so. And then I can use this to oil the wood. I'm actually going to put a little bit more. Make sure that everything is coated. The inside as well. I'm going to use a new piece for the sides. Now that everything is shiny inside, I can now move on to the outside. I'm just going to close this again. I'm going to use a new piece for the outside. There we go. And just rub that into the wood. Okay now for the last two sides I am going to again use a new piece. Alright, now everything's covered so I'm going to open this back up so that it can dry out and probably absorb the oil. I'm going to put this over here and then we'll continue after 20 to 30 minutes. So I'm going to put the lid back on here and that's that." + }, + { + "category": "woodworking", + "name": "User_15_414_0702_2_480.mp4", + "transcript": " Okay, so now it has been 20 to 30 minutes, so most of this should be dry. And first I'm going to put on my gloves and then I'm going to use this rack to just get rid of any of the excess oil. So I'm going to start on the outside and just wipe it down to get rid of any excess oil that the wood might not have absorbed. And now I'm going to do the same on the inside. Okay. Some more here. Okay, now this can go into the water bucket. Okay, and now I'm just going to replace everything starting with the stuff on the inside or actually let's replace all the hardware first. So first I'm going to put these clasps back on. So I'm going to take this And then I'm going to just turn this around to make it a bit easier for me. And then I'm going to align this. Take the screws. Whoops. Stick those in here and then screw them in using the screwdriver. And make sure to tighten it really well. Same on the other side. And now I'll do the bottom part. So I'm just gonna... Align that here and then stick in the screw and tighten it with the screwdriver. And now the clasp on the other side. Make sure this opens. Make sure these holes are aligned. And I'll attach the lower part. okay now i'm just gonna check that these open and close the way they're supposed to and then i'm gonna put the edge protectors back on so i'm just gonna take this and put it here And then because this is kind of hard to do on this side, first I'm going to, I think, attach all these corners at the top and then flip the box around as I go. So I'm going to take this and put it here. and take the next one and put it here and the next one and put that here and screw it in by rotating the screwdriver clockwise. Okay, now that I've done that, I'm now just going to flip this over and then we can screw this screw here in. And also attach these corner pieces. And since these screws are all the same size anyway, it doesn't matter if I mix them up. Okay, I'm going to flip it on its side and attach these screws. And attach another corner piece. Okay. I'll flip it over again. and attach the final corner piece. Okay, and now I'm going to flip it outside again and attach these four screws And finally, the bottom. Okay, and now the last pieces of hardware that we have to install are the handles. So for that, I'm again just going to flip it onto the side. Oops. And then take this, align it properly. I'm going to already stick all the screws in so that it doesn't move as much. okay and for this i think i'm actually going to use an electric drill because this is getting a bit hard for my hands so i'm going to take this oops and this where are the drill bits Okay. Well... Since I can't find the proper drill bits, we are going to have to do this by hand. So I'm just going to use this screwdriver, rotating it clockwise to screw this screw in. Same for the other two. Okay, and now the other side. I'm just going to flip this over. This is going to be a bit more wiggly, but it's still easier to do it this way. So then line this up. Take these screws. Line those up as well. Okay. And now we just want to replace what was inside. So we're going to open this up, place down these two bottom blocks. Securely. I'm going to take this and place this in between. like so and then we're going to attach these two. I'm going to take these metal plates off. And then just try to... Okay, and try to secure this roll in the middle. There we go. And now we can put these plates back on here. And then secure the whole thing with these. I'm going to put all four on and then tightly secure them. Okay, now that that is secured, I can place this back on top. Close it up. Make sure that everything in the handle is hold. Perfect. Now we just have to do a bit of cleanup so I can put this back. I can also put this styrofoam back. and then throw these away okay now this box is nicely oiled the wood it's clean and we're done" + }, + { + "category": "woodworking", + "name": "User_15_414_1811_1_480.mp4", + "transcript": " Okay, so today I want to attach some things to this wooden block. So first I am going to put on this safety jacket. So first I have to open it up. And then I can put it on. and close it back up. And then I can put this in the pocket right here. Okay. And then, so next what I'm going to do is I'm going to put on some gloves so that I don't hurt myself or cut anything. And then I'm going to grab the battery from over here Just gonna grab that, take that over here, and now I can take out the drill machine by opening up this case. I'm gonna also put this in my pocket. Okay, there we go. All right, now first what I'm going to do is I'm going to take this block, take these brackets that I want to attach, put them where I want them, and then outline these holes or where the holes should go with a pencil. Same on both sides. All right. Place this back to the side. And now I'm going to take this clamp and clamp the block to the table so that I can drill into it without damaging anything. There we go. Just going to make sure that this is secure. So I'm going to By twisting this counterclockwise, I can tighten it so that the block is nice and tight on the table and doesn't move around. There we go. Actually, I'm going to take this off again and instead clamp the block this way because I think it'll just be a bit easier. I'm just gonna turn this counterclockwise again to clamp it to the table. Make sure it doesn't move around, perfect. So then I'm just gonna, oh, first I'm gonna take this and attach the battery. And I'm gonna look for a screw bit that fits the screws I wanna use, which are these. So I think maybe the two might be good. Yeah, so I'm going to use this, put this into this attachment here, and then attach this into the drill like so by just turning this until it clicks. I'm done using this, I can put it back and get up my first bracket, position it here. And then I can take this screw, make sure it's in the screwing position. There we go. And then I'm just going to align this again. Maybe actually first I'm going to make a hole so that I know where it's supposed to go. Like so. And so. Up here as well. Alright, now I can attach the bracket and this already has something to hold on to. So I'm going to hold this bracket, place this screw here. This doesn't have to be perfect right now, I'm just going to kind of try to screw it in. Now I can position this. I don't know why it's doing that. Maybe if I go a bit slower at first. Okay, now I'll take the next screw and fasten it up here. There we go. And now these other two as well. I'm just going to take the screw, position it here, slowly start to pull this trigger to screw it in. And pushing down steadily. There we go. And the final one. Same thing again. I'm just gonna hold this here. And screw it in. There we go. And now for the other side, I'm going to do the exact same thing. First, I'm going to mark my holes with this by just positioning it here, giving it a couple tops with the hammer, the same over here, and here, and here. Now I can take this bracket, position it here, take my screw, position that here and then slowly start to screw in and now I can position the bracket how I want it to fit and drill the rest of the way okay now the second screw for up here I'm just going to take that, apply pressure. And now over here, just positioning that screw and holding onto it so that it goes in straight for the initial screwing. And then I'm just going to put pressure with both my hands. And now for the final screw, which goes right here. Oops, I'm going to do the same thing again. all right now i've attached all both of these brackets and i also want to attach this block to the top of here so i'm going to unclamp this by turning this clockwise and then i can lay this down flat like this and attach it to move the clamp up so that it actually sits where I want it to, and then I can tighten it out. Make sure the block doesn't move around. Now I'm going to align this with the bracket. It acts as a nice barrier. And then I'm going to use this to draw a line up to where I want it to have the holes. So that would be right here and right here. And then I'm just going to take the width of this as the distance. So right here is where I want my hole and right here. So I'm going to mark that again with the hammer. Right there. and now again taking two screws place this exactly where i want it hold down the screw and then take this make sure that this is pushed out so that you know it's screwing in and then just hold onto this while i slowly start to screw this in Making sure that it's in the right spot. There we go. And now the other side. Just over here. There we go. And now I can take the battery pack off again. Take this drill bit up by turning this counterclockwise. Yes, like so. I can place this back in here. And this back in here. By pulling this down, I can release it. There we go. Put this back. This can go back to charging. I'm just going to slide that on here. And then I can also unclamp this. like so. Now I've successfully attached the brackets and this block. I can fold this back up, close this. I can take off my gloves and then take off the jacket. And that is it." + }, + { + "category": "woodworking", + "name": "User_15_414_1811_2_480.mp4", + "transcript": " Okay. So today I wanted to take these brackets and this wouldn't block off. But first I'm going to put on this safety jacket. So I'm just going to slip that on. And then I can store this in the pockets. The phone as well. And now I'm going to zip it up. And then next, I'm just gonna put on some gloves for safety. And then I'm gonna get the battery for the electric drill from over here, where it's been charging. So I'm just gonna take that, bring this over here, and then I can get the drill out. So I'm just gonna open this up. we go in order to take it apart i am going to need the correct screw bit so i'm just going to see which one i think fits i think the two might be good so i'm just going to test that out and that fits perfectly so take this out put this into the attachment and then put the attachment in here first i'm going to open this up put the attachment in close it Here we go. And first I think I'm going to take this top wooden block off. So I'm going to use this clamp to clamp the block to the table like so, and then just tighten that so that it doesn't move around while I'm unscrewing the screws. There we go. That's pretty secure. Now I can put on the battery. Make sure that this is pressed in in order to unscrew. And then I'm just going to hold this perpendicular to the wooden block and press lightly to unscrew. To unscrew this. Oops, a bit more. There we go. Now this can go back in here. And I'm going to do the same pushing this trigger with this pushed in to unscrew this screw. So I do need to apply a bit of pressure. There we go. Oops, a bit more. And then I can use this sandpaper just to clean up the holes. On either side. There we go. And now I'm going to unclamp this again. and then put the block right side up maybe this way around and then we clamp it to right here make sure it doesn't move around There we go. It's pretty secure. And then I can use the same attachment, same settings to take out these screws. The same over here. And then at the end I'm just holding it so that it doesn't fall over. Now I'll do the same over here as well. Starting slowly. Whoops. And then just grabbing it at the end to pull it out. And now for the last screw. And now this bracket is removed and I'll do the same on the other side. And now for the final two screws, again, I'm just going to pull this trigger, make sure that this is pressed in, and slowly start to unscrew them. And then I can increase speed. At the end, I'm just going to hold it so that it doesn't fall out. Oh, maybe a bit more. There we go. Same over here. There we go. Now this bracket is removed as well and I'm again going to use a sandpaper just to smooth this out. There we go. I can clamp it from the table. Put the clamp to the side up here. And I'm gonna use this dust pan and this brush to just brush off all the wooden bits. And then I can put all of this here, all the separate pieces, and then get all of these off the table as well, just to clean up a bit. There we go. I can put that in the trash. Okay. All that's left to do is to disassemble this. I'm going to take the battery off and put that back on the charger to charge back up. There we go. And then I'm going to take this drill bit out by turning counterclockwise, taking it out. And then I can also remove this by pushing this bit down. I'm going to put these two back in the case. And close that back up. Now I can take off my gloves as well. And the safety jacket. There we go. And now I've successfully disassembled this, took the brackets off, took the other wooden block off, and that was it." + }, + { + "category": "woodworking", + "name": "User_15_User_1_411_2310_1_480.mp4", + "transcript": " So we have to take So to deal with this, let's just put on gloves first. Oh. Oh. OK. No. I'm the same twice. OK. Looks. Then we are going to attach this clamp. Attach it onto the metal frame here at the bottom. We can extend it by pressing on here. in your case it is moving so we need to remove it or maybe reposition it so the problem is that this is the maximum extension of the clamp so we can tighten this a bit Try again. The block is now rigid enough so use the drill machine. Size one or size two should fit. Okay, now press this switch that it is going in reverse so that you can't move through with this. Okay, perfect. So now let's just start with one of the screws and hold the... I would recommend to put it on one so it moves a bit slowly. Thank you. Now I need to prepare this side for the operation soon. before we begin with the process we can just place the bracket and mark the holes so in the bracket one of the sides is shorter so the shorter side should align with the exact height of the wooden block so just confirm that it does and yeah okay so we're going to attach the bracket here at the left corner So I'm just going to mark my pencil roughly where I think the double should be. However, make this surface a little bit more. So we're going to use a rasp and just at 45 degrees, just slightly make the edges not so sharp. can use the flatter edge which might make it easier since we want to make the whole side we'll also need Yeah, in the middle, I think anymore. Oh. And also just make the surface. And then also the Armenian part of the other side. Once again we are in the block so that we have the bracket edge on the left. Then the tamping surface is quite small, so be careful. It's not moving. Now what we can just kind of do is see if we are able to attach the screws onto this, first of all, or if the wood or I think the first is a good idea so with this tool I'm just going to make a small dent move the switch to this side so that it actually is driven I think your location is just too close to the but I think it should still fit I think it's so take it out again no I think it will fit but I can't put the no I mean yeah you'll have to take it out yeah I don't think you need to do it but if you do then we can just keep this It's not turning. For me, pressing it very lightly works. But if I press it too hard... Maybe. I think it's... This is a bit in the way. or maybe it's because of the setting maybe you have to put it on this one because then it's more You should be able to turn that I think somehow. I think the problem is that the wooden block is too rigid so I'm going to have to Let's see different challenges. I think it's also harder on this side because this is going against the grain, whereas on this side it's going into the grain. you can just hold it with the bracket then you know that it is pretty tight for the little doctors. What we're going to do next is start with the tools away and turn the hammer and the chisel. And then just start attaching. and the last thing I think" + }, + { + "category": "woodworking", + "name": "User_16_410_0210_2_480.mp4", + "transcript": " Okay, start. Now turn on the light. Now I'm going to take this clench. I'm going to drill a hole into this wooden Next, put the wooden brake on the clutch. And tight it, fixed, tight. Good. Now, put the gloves on. Now I need a drilling head. Look out of this room. Close the door. Go to the next room. Open the door. open the door with the drilling head box open the box find a 7mm drilling head put it on tight when I heard click, cluck, and then use the ruler and the pencil to show From the left side, 3 cm. 3 cm. From the above, 2 cm. It's just here. Make it across. And next, connect to the power. It's fixed. Yes, it's fixed. Now drilling a hole. Oh, another way wrong. Do it. This is approximately 2 centimeters in deep. And next, find a sandpaper. Now here is the sun paper to smooth the surface. Use this to smooth the edge, the side. Now the hole is drilled. Untied. Unpower this. Take the drilling head out. Put it back to the box. Drilling head box. 7mm. Untied. put the trailer back put the sand paper and this back also put the hood back this is my hole and then Yes. Clean it with a little brush. Clean everything. Clean the floor, the wooden. Put the trash into the trash can. Clean up. And the film is finished." + }, + { + "category": "woodworking", + "name": "User_16_412_0602_1_480.mp4", + "transcript": " so in this task I'm going to use the oil to polish the wooden block wooden box so first put on the gloves using screwdrivers to remove the bolt remove all the connection part of the this wooden box and turn around remove this part or continue remove this part by using the screwdriver Now this part is removed. There it says the handle. Lift it up from the ground. Remove the handle and sort all the leaves. Put them all together. Turn around. Remove the back side. The connection part. remove 4 bolts and also this loose the bolts loose the screws loose the screws here also remove four bolts and open this and turn the around and remove the bolts from the cover side remove them one by one remove them put them together check it's going this way remove it another way another one okay, sort them put this aside Remove the handle from this side. Remove the screws. The middle screw. Third. Fourth. The last one. 1, 2, 3, 4, and 5 out. I will sew them together also. Finally, remove this. Front, middle. Okay, this is stuck here. remove the metal chain put it away now we are going to take out the cloud and the cover put the cover underneath so that will protect the First we have two parts So we have the box part and the cover part. So I first have to smooth the edges of the cover part. Use this sandpaper. Now we use the little brush to erase the dust. Clean it. Now, next we use the use the cloth spray some cleaning things to clean it first also the backside spray and use cloth to clean and next we open the oil can First, this is the back side. So we have some oil here. And we use the cloth to put the oil on the surface to polish it. L at the edge. Also this edge. Third edge. next turn it around Seems not enough. So we put some more here. now the cover side is polished with oil next is this part also first cover the oil can for a while use the clean stuff to clean up the enum part it's a different way of cloth clean in from the back side smooth the surface using the sun paper use brush to get rid of the dust now you see the cleaning thing The cleaning thing is finished. Now first, when you use the oil can, open it and put some oil in here. Use the clot to clean the surface. now each surface, each side next Next. Now the floor side and basement are done. Now the inner part. So with the view. Now all the surface and the inside and outside are soaked with oil. It's polished. Now we put the clot back into the water box. Close the oil can. wipe out the gloss some oil wipe the tools so now we're going to put the thing back here now first put this metal thing back to here Using the long screw. Okay, now I put the handle in, back on, which is this way. So we're going to use five screws by using the screwdriver to screw it in. Fastening. Next. next next Now first, this handle is in. Turn it around. Put on the next handle. Unline the position. next screw fastening next screw fastening next screw fastening next screw fastening so now this handle is also back on next what we are going to do is put this back on so this thing is going to be like this way like this so we are going to also use two screws next next here Unline the causation. Make it tight. Next. Fastening. So these two sides are finished. Now we turn it around. Put this back. check this way which is like this align the position second one third one on on on the position and fastening, tighten second one also fastening, tighten third one fastening, tighten next Now I'm going to open it and also screw them in. Next. Next. Fastename. Titan. Next. Fastename. Titan. Next. Fastename. Titan. Next. Fastening. Tighten. Final one. So fastening. Tighten. Now it's able to close properly. Finally we turn it around one more time. Put the screws back in here. Line the position. Attach the screw. Fastening. Tighten. This one. Fastening. Tighten. The last one. First align the position. Fastening. Now this is finished. Check. Good. Lock. Good. Unlock. Good. Open. Close. Okay. So we're going to put this Here let them dry out also use the towel to clean the hand also clean the table So clean this up, clean this up, take off the gloves, and the task is finished." + }, + { + "category": "woodworking", + "name": "User_16_414_0511_2_480.mp4", + "transcript": " I will work with the wooden block. First put on the safety vest. put on the clothes based on the instruction first inspect the old block So what we do is check if this bracket is unscrewable with the screwdriver. Let me check. It's pretty hard. But it is pretty hard. The best thing you can to clamp it on the table. right make it tight test if the whether this block moved no it's not movable so prepare the drilling machine from here drilling machine put down the battery get the drilling bits Find a suitable drilling pad. Yep, it perfectly fits. So, connect into the drilling machine. Another way. Carefully unscrew it. Hold it. Make it harder. good now it's out unscrew them and unclamp the clock put them away and clean this up use a little brush to clean it and then take the new block check mark a side on the block you have to mark it it's looking like this so I'm gonna use a pen to lock it let me search for a pen that doesn't have a pen so I'm gonna use this little thing to draw mark it yeah you can see it's here so we can mark the position doing this And down here. Right. Move it to the desk. Make it tighter. I'm sure it doesn't move. None at all. And the four edges of the corner of the face. Yes, I spin it. with the metal tool. Now I'm going to go for the metal tool. Go with the hammer. Since this room is locked, I'm going to use another way. Let's use this to drill a hole. This metal tool. And a screwdriver. let's check these holes are suitable yes it is suitable so come in tight use the trailer machine do not screw in tightly so gently screw in I'm going to Lower the power, lower the strength. Not completely And it was here. Make it power more. More power. Checking whether there is any movement. Loose, no absolutely not. It's very stable. I will unclamp this wooden block. I take care of the edges. Now it is complete. I'm going to clean everything with a little brush over here. remove the battery into the box And stop." + }, + { + "category": "woodworking", + "name": "User_16_414_1012_woodworking_1_480.mp4", + "transcript": " Now I put the mask on and now I put the gloves on. Be careful. Now I need to disassemble this wooden box first. I need to unscrew the screws using the screwdriver. by one remove S, send, and par. this card is removed so this card is on the left Next is the handle from the side. Here are five screws. and handle this out this from the left side like this then the right side this one the lower left this is the right side handle from the right side sort everything Now disassemble the connection of the cover and the lower part and the upper part. There are four screws. This is my hand. And then the last two. This is my left hand to hold the plate. My right hand using the screwdriver to loose the screw. The last one. Then this plate is out. Put this plate away. four screws. this part is out second and then this thing is also out Now we need to remove the metal plate inside of the box. Remove this connector. Remove the plate. Remove the bolt. So this wooden box and with the cover is disassembled. Now I use the sandpaper to clean the This color part. And use the cloud to clean it a little bit. Clean this. Put the sun paper away. clean this and next clean this a little bit wipe it okay next using this intensive flake to clean the inside spread a little bit more inside the red blood red color bloodish thing this side rotate it Now this is all This upper part. Other side. This side. Next, rotate it. The next one. now every part is cleaned up put them aside" + }, + { + "category": "woodworking", + "name": "User_16_414_1012_woodworking_2_480.mp4", + "transcript": " then put the gloves on the mask is already put it on check the mask good now we need to assemble this wooden box the two parts with the screws and the connection part but first we need to paint the box be careful using the clot Paint the color for the inside. Now the first side is fully painted. Be careful of the edge. This also needs to be painted. A little bit. A little more. Okay, next part. So the edges are painted with the color. Turn one more around. make sure the corner is painted and the inner part is circular to paint turn around do the same thing Now, the painting is finished. The fourth side is painted. The inner part is also painted. Now what I need to cover the Put it aside for a while. Now, you need to screw the part back. First, wiping the hand. Let's cover this. Wipe my hand with an unused area. Define the connect part. This should be this way. Using the screws. Screwdrivers. back to them and the other side so this way second the third and the last No, that's the side. First. The third. The fourth. Just screw the screws in. And the last one. Lower right corner. Screw it in. Next. What we need is this. like this so we can close them like this we need two screws use my finger to align the position Next, the lower screw Use my finger to fix the position Now, the next part. Also here. Put one screw in. Align the position. Not so tight. And another. Now another handle. They also have five screws. You need to screw them one by one using the screwdriver from the top right. upper right part one in next the middle one The last one. And lower right. Make everything fixed. Now they are all in. We need to put the upper cover in also. Which is here. So remove them. Like this. Screw them in. A little bit. Second. Now I don't need to hold. So I can use the next one. the middle one the fourth one from one side screw them in and next another part another side hold them a little bit it's in another side this is in the middle one this is in the last one it's also Now it's also in. Now it can be closed properly. The last is we need to put this back on. From the top side. From the cover side. So the one first. Find the position. second one fixed the other side we also have two screws one by one the first the second let's try to close close properly good the handle working good open the connection part working good so we are finished take off the shoe and shoe close" + }, + { + "category": "woodworking", + "name": "User_16_414_1911_1_480.mp4", + "transcript": " OK, I'm going to drill the hole in this block. So first, put on the safety vest. Put on the gloves. Put down another hand. And now, if we want to drill a hole in this wooden block, first I'm going to use this to smooth the edge. now I need the drilling machine open the box take off the drilling machine take off the head and also this drilling machine need this battery for this drilling machine so Clamp on, check. Good. Put it away. Now clamp this. Hello. Sorry. Okay. Clamp this on the desk. so if we want to stick this in this block we need to first make a sign for this also here Okay, so I need to drill a hole here, here, here, and here. Also here, here, here, and here. Mark the position and put the drilling head on it. try the number 2 cross shape it fits so put it on connecting to the training head use this to start the little bit through the hole a little bit as well as here also here so here make it deeper Also another side. Here. Also here. Here also. now clamping faster and tighter using this to drill make it softer put this on ok and next is another hole underneath And then another one. And the last one. Okay, good. Now, another slide. Okay. Next. and then put this hole next the last one okay good now it's fixed just line with the edge here also you can adjust the angle a little bit use the hammer it's better now now we unclamp this we need to connect this also need to clamp Line the position first. Here, roughly. Check if it's one centimeter. Here it's also one centimeter. Okay. Climb it tight. marker position here also here align with one here also with one centimeter it should be here now mark the position I use this to drill a little bit get a hole okay now we need to use the drilling machine to drill a hole for this we need to hold it It's a higher power. Now the other one. Put more power on it. Okay, good. Now, check it. Use a brush to clean the wooden pieces. Smooth a little bit. A little bit. Now, check the feet. Good, good, good. Take it off. Turn ahead. Put back into the box. Take off the battery. Put the drilling machine back to the box. Charge the battery. Turn it off." + }, + { + "category": "woodworking", + "name": "User_16_414_1911_2_480.mp4", + "transcript": " Now I'm going to remove this wooden block from the bigger wooden block. Just put on the safety vest. down the gloves, left hand, right hand. Let's check it. Smooth the age. And then clamp it. we need the drilling machine from the drilling box and the head also for the drilling machine we need the battery find the drilling bit This might be the most suitable one. Try it. Yes. I'll also try another one. This is more suitable than this. Put it on, connect it to the drain machine. First we need to remove this part by unscrewing this. OK, one out. Here's another one. One more power on it. Good. So this part is removed. You can unclamp it. And remove this wooden part. And clamp it. The bigger part. Make it fast. Also remove this. Little by little. Soft. So here. So here. This one as well. The part is removed. Now this side. There. The last one. now they are all removed and dive into the box unclamp it to smooth the hole here. Okay. Now put the wooden box here. Remove the drilling head. Disconnect the head. Remove the battery. box, charge the bedroom. And here is also a little bit of dust. Clean this off. Take off the screws, the safety vest. Finish." + }, + { + "category": "woodworking", + "name": "User_16_User_1_411_1810_3_480.mp4", + "transcript": " We're going to remove the plate from this. From the wood. It's tight. It's too tight. Quite securely so we can't move it. It's stuck in the wood. No. So let's drive with the building machine then. So the first thing that we're going to do is open this up. you can open it by clicking on this on your other side yeah and open it like this and clamp it clamp it onto the trigger yeah sure No. No. Perfect. Then we're going to try with the drilling machine. So take the drill bit out and select the one that suits the best. Think and compare it here. Both that we have here. And number three should we find. Let me check. Put the trillion head into the trillion machine. We can put on the gloves. Is that a pair? Okay, one and two coming out. Here comes the next one. There's height. Yeah, this works. You need to press it very high, very hard. Perfect. So, I'm going to place this. And it's done. Then the operation is complete. Put it left to the side. Remove the cat? Sure. The process is complete." + }, + { + "category": "woodworking", + "name": "User_16_User_1_411_1810_4_480.mp4", + "transcript": " and the way you align this is so you can see that one of the ends is shorter the shorter end is going to be attached shorter should be attached so yeah exactly which way this way okay cool okay so the first thing that you can do is firstly you should just clean the workspace just grab that cloth okay use brush right now to use the brush Okay. Okay, now what we can do is just mark with a pencil where we intend to fix this and exactly know where we should drill the holes. I'm just going to mark this. Just mark on the boundary of where I can reach. Okay, okay. Do the same. okay now we're going to to guide the holes in we're going to hammer a few small holes Gently at the top. The first one is going to be hammering a small dent. Clamp is already a little loose. Tighten it. Tighten it out. Now, let's take the grilling machine first. And if you haven't already attached the... The battery is already on. Clockwise. I'll take... I'll try. make sure that this is done on this side And then when it's already done, you can remove your hands. Press it. Press it. Maybe the, it's not. Clamp is in clamp, so I think we should. Yeah, I should. This isn't talking to me. Yeah, adjust it now. Yeah. No, adjust it first. Okay. You just lose it? Okay, sure. Now we can close it. I hope it's not. The drill bit is quite powerful and quite hard. Okay, so move it up. I cannot go inside anymore. Okay then, wait a minute. Maybe... Put it out? And use... Okay, let's put it out. Put it out? Yeah, put it out. I hope I can put it out. All right. All right. Okay. i'll try it and try without the the problem we are facing is that the the wooden um oh it's coming inside yeah the wood that is that we are compressing is not able to come outside because of that it's not able to uh let's say exactly uh find the right place yes these larger holes here but they are definitely too big I think you should, one way around, turn it inside. Yeah. I think you should, you are around? No. No? Okay. Maybe this is good, but it isn't sharp enough. Mm-hmm. This much? Yeah. Mm-hmm. Or should I do it also? Move the head. Maybe we can use this. Hm? I think I can just make it in. mine is finished yes i think your block is more harder than mine looseness Use my brush to clean the... It's still not. Maybe if to drill a hole more deeper than that one maybe. Maybe that one. And in this case, I'm going to align this on this end. And this is in place. or i can hold this one you can press the trigger machine Okay. Okay. His face. Move the head also for me. Next to the charger. Charging. the floor a little bit. Mm-hmm." + }, + { + "category": "woodworking", + "name": "User_16_User_14_411_1810_1_480.mp4", + "transcript": " Okay, first we need to put the gloves on. And we want to remove this metal away from this wooden block. First, I have to use this to clamp this on the table. Be careful. Attach this. Do it here. Do it in the middle. No, not here. So that can make it very tight. Yeah. fixed so now we need to use the screwdriver machine and pick up a head Try the number two, if that fits. Yep, that fits. I would use this one. I'm going to try which fits. Also, this drilling part. Does that fit? Okay, cool. Not fits that much. Let's try another one. This one. That fits more better. Yeah. Okay. And then don't forget the set. It's the red, red side. Yeah. Okay. Yeah. Just put it inside here. Yeah. And connect it to the, no, no, no. You have to lose it first. Yeah, when you hear it click, that means it's fixed. Just remove it. And I'll remove from the top. Be careful, be careful. No, no, no, no. Just push it, push it hard. And yeah, not that fast. Slowly, slowly. You can do with mine. Mine might be not so tight. like what I'm doing. Just push it, push it forward, push it forward, push this forward and slowly, slowly, slowly. Just softly put the trigger. Softly. Softly. Yeah. Softly. So it's more softer. Yeah, like this. Yeah, softer, softer. Because if you are too quick, that will just lose the attachment. So just do it very softly like this. Like this. Yeah. And that will gently come out. No, too quick. That was too quick. You can try without this. Yeah, yeah, right, right, right. Like this. Push it forward. Push it, push it. Yeah, that's correct. And also do with mine. Yeah. And then is the next one. Yeah, sure. Push it and slowly. Yeah, that's good. Oh, slowly. No, no, no, don't worry, don't worry. Slowly. It was too good. Push it and slowly. Yeah, this speed is really good. Okay, I think you can put it out. and now because we can see this screw is almost almost unusable right so we can change a new screw like this the bigger size which can mean which can be more suitable Let's see if that can fit in, which can fit into this. It's a shorter, shorter way. Yeah. Yeah. They both can fit. I think it doesn't matter. Don't need to be so long. We can pick some shorter. shorter size, this tool, this tool, and this long. You can check if that's the thing. Yeah, okay, we can use them. And next, we have to remove the head to see if this, this head is fit into this screw. I think it's, yeah, might fit, might fit. mine perfectly fits. You can say if you are fits, you can try with the bigger one, bigger size could be more easily. No, not this one. Maybe this one. Yeah, this one. Feeling good? Yeah. Mine seems like too big, but you can try. Yeah, yeah, you can use this. This one seems like good. you don't have to change yeah okay great let's see if mine No, no, no one way around there. Yes. The shorter side. Now we check if this wooden block is still fixing to this table and make it tighter. And we can use the same holes here. Yes, I also use my same holes here. And don't forget to change it clockwise to make it, screw it in. And remember, do it slowly. Just click here. Yeah, over there, yeah. Push it, hold it. Oh, yeah, you hold it, I push it. Okay, you try this clockwise. Try this clockwise. Yeah, slowly. No, no, no, get in. You can put it in. Yeah, slowly. Okay, good. Yeah, good. No worries, just push it and slowly throw it inside. No, no, don't worry. You can continue with the second one because don't, don't, don't, don't tight it too much. Yeah. Good. Mine is finished. You can check with yours. Yeah, let's do it slowly. Yeah, slowly. And push it from here. I will help you to push it. OK, good. You can continue with the top one. Yeah, good. It's stable. Great. And then we can lose the plunge. OK. I also need to remove this. Remove? Yes, yes. I don't know how. Just a little bit too tight here. and remove the head yes and put it back into the box no no no and remove the battery i'll clean it up use a little brush Yeah, pull it, pull it, pull the right, no, no, no. I mean, like, put it right, right, and then it comes out. Why are you missing one? It's not here, right? No. Okay. And you can put it aside. No? Okay, no problem. And you can move the battery from the machine. You click that. And yeah, great. And then put this away. It's perfectly fit. And then clean a little bit of this. Take the straw back into the box. I think there's still something on the ground. I'll clean it up. Okay, then finished." + }, + { + "category": "woodworking", + "name": "User_16_User_14_414_1202_1_480.mp4", + "transcript": " now we are going to disassemble this put on the jacket here's yours put my jacket on and then put on the gloves what are we going to do is first let me check remove the bolts search for the proper drilling head check if that fits Yeah, this is good. What's going on with this one? I broke it. I mean, the head is broken. So the head. Yeah, it should be like this. Yeah, it's damaged. It's also damaged. This one? It's almost a circle. Put on the gloves. We have to clamp it. You clamp this one, I'll bring another one. So what are we going to clamp is... let me think, how should we climb it? maybe we can climb this angle it's hard, it's pretty hard so maybe this, yeah, sure okay Tight. Good. Now I think I can do this. Hold up this. Thank you. first one over here second one it's also damaged it's so cool so I'll skip this Yeah, it's out. Put it here. The last one. No, not the last one. This one is out. This is the... I need to find another key to maybe this or maybe this. Why do we need hammer? Of course not hammer. Use this. Yes, we have two of them. Let's try which one fits better. Okay, so maybe we can... Yeah, I'll clamp this and clamp that one. Okay. Let's put this away. Now... that's too tight but it works so i think it can go out i'll pull it out it's not what to pull out because this you can see this uh no it's not a straight yes it's a yes good it can be out and throw it away it's damaged so we put it another way where is the small thing is here right let me check if we can put this out it's hard okay good now we put it out the damaged part put the Let me check if there are any remaining. Smooth it. You can do it like this. It's more easier. wait a second I can use some sandpaper to smooth it no no it can be more detailed in case we use hand it doesn't hurt our hand so more detailed like this more detailed like this and more detailed A little bit of cleaning up here. we can clean it after we take it out this is cleaned And I use some paper or you can put it on and I will send people this I can clean this up now Okay, but we need to we just Also smooth this one also, I think. This one also. Okay, this is cleaned. The cleaned, put it here. Okay, you can rust in there, and I can rust in here. I'll just use the sandpaper. Just use sandpaper. Okay, I will help you. This one is also send it. So I'm going to keep sending on this one. You can post it on that part. I can send this part. You can separate it. I was on this farm. Okay, that's all finished. Okay. Okay. okay thank you i'll clean this up cleaned. Okay, I have to clean this. Good, so they are all cleaned, so each side. Okay, now, okay, wipe it. Now it's finished. Take off the gloves." + }, + { + "category": "woodworking", + "name": "User_16_User_14_414_1202_2_480.mp4", + "transcript": " we are going to put on the jacket and then put on the gloves in your clothes so yeah to be safety we need to put the clamps on I think we can put them together yeah like this so I think we can try your idea so which is put this here and maybe you can put it here this is the base yes this is the base so if we want to drill a hole connecting these two parts together we have to like this right okay to connect in these two parts with bolts and glues so maybe you have the we have the glues yeah stick them together Do we need to mark the position first? Or we don't? Let me think. No, we don't. We can just try it. Well, we do. Yes, we do. We can mark some positions. Here's the... I will hold this and... You should measure the total length. Unfold it. Not all of them, but you can rate it. How much? 81. How much? 83. 82.5. 82.5? Why are you marking there? No, not there. No, we cannot use the same hole. So let me think how to divide by. So we have three holes. So one, two, three. So like 20, 40, 80. 80 it's almost 82 yes three holes because one one bolt is it's defected so we divided by four is 20 per each 20 40 60 yes we can do 20 40 60 here but i don't think it's stable we may be need to drag a 10 and 70 and 40, one more. 10, 40, 70 will be stabilized. Give me the pen here. 10, 40 in the middle, sort of middle. 70. So if we have extra, so we could like 10, 30, 50, 70. So that would be much better. 71, 70, 10, this one. So 30 and 60, right? Or 30 and 50. 30 and 50. We can let it go. So we'll draw it here. One here. One here. One here. So where the position I marked the coins. One, two, three, four. Before that I can use the To measure distance, it's one millimeter. So we can. This is also one. This is also one. So this is also one. So make it back. You can hold it. Yeah, thank you. So this should be like here. I can delete the first. How much is this? Yes. There should be one there. Yes. One from here. I draw too much. Right here. Roughly here. It should be one millimeter here. OK. So a little bit difficult to say, to see. But we need to prepare the tool. Where's the drilling machine? OK. OK. Thank you. And we need to try to drill a hole. Do we need to use the screws or do we need to use the trailer head? We can try to use the trailer head. Yeah, the trailer holds will use the trailer head. Can I compare? We can do it a little bit. Can we? Is that able to use in this studio machine? Yeah. No, no. What are you doing? No, no, no. It's like this. Okay. Yeah. And how to put this on? Just like this? Yeah. Are you sure? Let me, let me do it. Let me do it, let me do it. Oh, like this, right? No, not like this. Like this? What? Okay, you can do it. Slowly, slowly, slowly. I'll do it, I'll do it, I'll do it. It's dangerous of you. Yesterday I did it. Let me try it. Right position. It's a little bit hard. No, it's here. I think a little hole will be fine. And another one. That's not enough. You can through a small hole. I'm going to drill a very small hole. Do we need to drill a hole over here also? Yesterday I didn't. I don't think with your hand will be good. I think we can just first glue it up. Now we have the hole and we have the everything. We have the mark, so we put glue on it. It's too sticky, this glue. I think this is almost finished, so I'll use this one. This is also almost finished, so I use this one to finish this up. I think before this, we have to prepare our clamp. Yes, you can wait a second before you do this. No, we can do it later. Okay. Carefully, carefully, carefully. At the edge, at the edge, at the edge. You focus on this part, I focus on this part, yeah. Okay. Fine. At the edge, at the edge. Yeah, but the length is not. Please don't worry about that at the age. Yes. Can you press it? Yeah. It's a little bit gap. Should we also clamp it? Of course we need. And we need to like hold it a few seconds. Yeah. So I will come clamp it. So you mean like this? Clamp like this? Because these are not aligned. This is good. This way. Hold this. Let it not move. A little gap, but it's alright, I think. Too much pressure. So not that much pressure. Okay. So we can drill the hole now. Just tighten everything. Tighten up. Not that tight, but as tight as possible. Make sure it's not moving around. there's also here okay now before everything we can just check this good okay so use another or drill a little hole here Well, yes. we can try with our screws I can hold it. I'll hold it. Just be carefully. Oh, shit. It's too high. Where's that bolt? Oh, here. Hold it. It's not straight. See? yeah it's not straight it's pretty hard to blink it straight so i'll try my best Okay. It's all right, I can see. There's nothing here. Sounds good. Okay. Should we need to tighten this up? Much more further in. Okay. More further in. No. So, so, so. Give me some space. Thank you. And I think you can leave your finger away. Oh, wait, there it is. Okay, good. Let's see. It's all good. Nothing shows up there. Very nice. And one more. Don't give me that bad one. Where's the bad one? We said we have four. We said we can take more. It's over there, I think. It's over there. Yeah, you can check it there. I'll come with this one. okay this looks good this there is one see here here here here take one here It is straight. Good. Huh? What? Huh? It was my idea, so let's reclaim it like that. Good. Let's take it out. and we check this is stable and maybe you can Yeah, maybe you can try to put something in here. Here it comes. Okay. No, no, you shouldn't hold that. Hold this. Yeah. Use your hand. Use your hand. Yeah. Yes, this is stable. Take it out. Okay, and move it right off. It's all good. Look. Touch it. So it's all good. Set it in this way. All good. Four nail screws are aligned. yes it's good it looks good yes it's good great now we clean this up and put it away put it here like here and sort the items so your idea worked yeah the idea the idea worked Good. This is our defect thing. Wipe this also. Yes, I will clean this up and store this. Oops. OK. Cloud. Store this. OK. Put it here. Put this back. And that. Put this tool back. yeah so we finished about the clothes and the safety vest folding" + }, + { + "category": "woodworking", + "name": "User_17_414_0402_1_480.mp4", + "transcript": " So now we are going to paint this small wooden block on both sides, this side and this side. So we need clothes under the box to protect the desk and gloves. and also the paint and the mask so first we need to use the sandpaper to smooth this a little bit And we have to clean it a little bit. Clean with this, close. Yep, so now we have to paint and we have to take on the mask first. open it and then shape for a little bit and the pan so we finished painting this small wooden block and we can leave it so we can wait for it to dry so this task is finished so we can take off the gloves and also the mask" + }, + { + "category": "woodworking", + "name": "User_17_414_0402_2_480.mp4", + "transcript": " so for this task we need to first assembly this wooden box and clean it with this and this clothes and assembly this wooden box so first we need to remove all the screws here and all the parts Here, here, here, here, and here. So we need some screwdriver. This screwdriver I think. so this part is off now we can remove this part and now for these two logs And then there's hench. And also this part, this part. So there's still eight screws here. We also need to remove these. and yep that's the upper part and last one is this so we can use our hand to unscrew this and take this out so we now detached all the small parts here on the wooden box so now we have to clean all the parts with this so we need the gloves and spray to each side of the wooden box in white with this clothes. And also this, the other side and bottom. And also this. so now we clean the wooden box so for now we have to assemble it put all these parts back so the first is this one And this one, this more. We have to make sure if this really... No... So this should be on this side and also this part Yep, yep, it fixed. And... and we can now fix this And the last two parts is this. So... so now we have to check the box we should say if it works and if it locks and yep so it's not really moving or so everything is tight and yeah so we finished the task take off the gloves" + }, + { + "category": "woodworking", + "name": "User_17_414_0402_3_480.mp4", + "transcript": " so in this task we have to use these tools and sandpaper to smooth the edge all the parts and clean the wooden box and put something inside the wooden box and last we need to use the screws for for all these parts so first we need to put on the gloves and use the sandpaper to smooth the edges a little bit so take this out and this we don't need this right now so the sandpaper here so we have to go for all these edges so prevent if we are holding this moving this wooden box we are not going to hurt our hands and so also we need these these tools but we need to first use the clamp to lock the wooden box. Yeah, so it doesn't move. And we need this for the edges. Lock here. and also these. and also the sandpaper and smooth yep so now we can remove the clamper and clean that with this And close. And finally the lid stopper. so we will put all the things back this one and also the also the block here I also need something to make sure it doesn't move use this one instead it's like padding in the" + }, + { + "category": "woodworking", + "name": "User_17_414_0511_2_480.mp4", + "transcript": " Yeah, let's start. So this time we're going to remove this part to the new block. So first we have to take the safety kit, the jacket and glove. First, we have to see if we can just use the screwdriver to remove the system. It's very tight. This one is pretty easy and this one is pretty tight. So first we have to clamp this wooden block to the desk using the clamber here. yep so yep it fixed it doesn't move so for now we have to we have to use the screwdriver machine to unscrew the screws the drilling machine is here and we have to find a suitable drill bit for the screw so it's across this one yep this drill bit fit so install the drill bit to the drill machine and so it's vertical and this one and so this wooden block should be moved and this will loosen the clamper and move this block aside and we need to do with the new block So we need to draw a line here and to see where we can fix this part to the wooden block. and use a camper to fix the wooden block to the desk And still we need to drop two points and that's the position where we scroll. and we have to use the rasping tools and do all the edges And we first loose the glamper. Face another way. and do this part, this edge so the next step we have to use a hammer in these and create a little bit of hole on the surface so this time we have to use the drill machine again and draw a little bit drill a little bit and to see whether the screw can go right into the block so yep that goes right to the deeper so we can pull it out and this part we'll try it again Yep, so the screw can also go into the block, so we'll unscrew it. So this time we will try to fix this part to the wooden block. So it should be this direction and then Bye. so we turn to some stronger force now it's really hard hard to to let the screw keep going so we need to change a little bit We'll try one of these to drill deeper. yeah so this part fixed and we'll try to remove yep so drill a little bit further and this one too And we'll change back to this bit. And try to install the screw again. We have to clean a bit. and knot tied first and through the other So we tweak a little bit and tie the screws. It's a little bit to the left. yep so this time they fixed the edge so the task is finished so we remove the clumper And clean up a bit. And put the tools back. and pull the safety kit aside Yep. So the task is finished." + }, + { + "category": "woodworking", + "name": "User_17_414_0612_Woodworking_1_480.mp4", + "transcript": " so today we're going to clean this wooden box with this spray and we also need the mask and the sandpaper we have to smooth the edges so first we will disassembling the wooden box with the screwdriver so first we have to remove these two parts So we put the screws and the iron parts together next to each other and there's still one here. and next we have to remove these two parts so we can separate the upper part and base the screws are all the same so and there are still some screws here on this side so we still have to remove these so right now we can remove this part and the last one So this upper plate is completely removed. And for this base, for this frame, we need to remove the handle here and here and remove this. So we first remove these handles. so finally we have to remove this to this one iron plate and we can unscrew this with our hand and we can pull this out and the big screw. So the next step, we have to clean each part of the wooden box. This is spray campus thing. And we have to wear a mask because it really smells bad So we will wait until this other wooden plate and the blaze dry out. So this task is finished. We just have to wait." + }, + { + "category": "woodworking", + "name": "User_17_414_0612_Woodworking_2_480.mp4", + "transcript": " so this time we are going to pin the bottom plate to white and assembly the wooden box again so first we need a carpet so we won't pin the surface of the desk or any other stuff to white So we only put the bottom plate on the carpet and cover other plates and tools. And also we need the mask. so now the paint is almost dry and we can put down the mask and we will first assemble attach this iron plate to the wooden box and in the end we will put this in the middle of the wooden box and screw it with this one We can first attach this plate to the top plate. And next one is this. In the next step, we have to attach to the base. and decide to So let's open it and close it. It works fine. So next we will attach these two, attach the lock back to the base. and the next part is this plate for the lock so we still need two screws No, it's the other direction. and the lock is tight so we can try and test if it works yep it works so the last part should be this bigger plate we'll first put the screws in and put the plate and we can see we'll test a bit if the pan is dry for now still not so we should wait for a minute we can first remove this carpet since we don't have to pin it anymore so now we can place the spools and place the iron blade and tie it with this So finally we finish this and we can check if each part is fixed and works as normal. So this is the end and we finish the task." + }, + { + "category": "woodworking", + "name": "User_17_414_0912_Woodworking_1_480.mp4", + "transcript": " so this time we are going to disassembly this wooden case and clean each part of it clean the upper plate and this frame and the lower plate with the spray so first we need to remove all this iron plate and handle lock everything so first we have to use the screwdriver to untie the screws So next step, we have to remove two handles here and here. next we have to remove these two plates first we have to remove the outside screws And there's still more of it here on this side of the wooden plate. So the upper plate is completely removed. The last step should be this. And we can untie it with our hand. So we can remove this. So right now we have finished the task for disassembling the wooden caves. and for the Thanos tab we have to clean every part of it this upper plate and this frame and the lower plate so we will use this one and this this rack and also we need the mask and our gloves so we first put on the gloves and we will spray it to each part of the wooden case and wipe with this rag so we need this mask OK, so now we finished cleaning the wooden case. So now we will wait until the surface is dry. And that's it." + }, + { + "category": "woodworking", + "name": "User_17_414_0912_Woodworking_2_480.mp4", + "transcript": " so this time we are going to stain the wood surface of the bottom plate or on the inner surface here and we will use this in this rack and after that we will assemble the wooden case again Yep, so these will be the task and we will need a mask, gloves, screwdrivers and all the parts belong to the wooden case. So first we need to put on the mask and stain the wood surface here. Bye. so we have finished with handles and this the last should be the lock So we finished assembly the wooden case and we have already pinned the interface. So now we'll check this wooden box works as normal. So first the wooden hand is fixed. The handle is fixed. It doesn't move. And the lock is tight and the wooden case will not open. Unlock the case. the upper plate can rotate as normal and fixed so we finish the job and this plate cannot be attached because the paint is still not dry we have to first wait the paint to dry first and attach this part later so first close the wooden case lock it so then we finish the task" + }, + { + "category": "woodworking", + "name": "User_17_414_2511_1_480.mp4", + "transcript": " So now we're going to disassembly this wooden box, wooden case. So first we have to wear the gloves. So first we could remove these two parts and so we will unscrew the screws here There are two more screws here. So now we have to remove these two parts. so to remove this part there are actually 8 schools there are 4 here and 4 here so we first move the other side then for the inner side So this wooden plate is completely off from the frame. So we can polish a little bit with the sandpaper here. So we'll put it aside and now we have to remove these two parts on the side. So one left. So the last part could be this one. I just unscrew it with my hand. So the last step should be polished a little bit with some sand paper. Yep. So that's when we finished the task." + }, + { + "category": "woodworking", + "name": "User_17_User_2_411_1410_1_480.mp4", + "transcript": " as well. And also use this clamp here to mount it to mount the plate to the table. with some double-sided tape here. You can use this cutter knife to cut it in here. But how long should it be? This one? Yeah, exactly. The other side. The right space. There are two, just one. And then try to align very close to the edge. So the clear one. yeah right position should be stable and secure and now we And that are the blocks we are working with. The very first thing we are doing with those blocks is removing the screws and detaching this bracket because we want to attach it to the very edge of the side. how to just pull it really you can simply pull it out this kind of structure doesn't really like basically put it back up again like this and then angle up and put it down is this a round station? let me try we can try with this one So you have to find your angle. Yeah, see like there's like a little, little gaps here. Oh. If you angle it this way upwards. Oh, yeah, yes, I know. It will move very easily. Yeah. Okay. Yeah. So just take your phone. And clamp your block to your table. Maybe, yeah. Yeah, it's stable. Okay, so now we will be needing our training machines. This is yours, and first we have to assemble them. Therefore, we can use those two boxes here. Before that we can also put in the batteries. Just remove the battery by pressing this button. Then we can slide the yellow part into here. Yep, that's all. Press the button. It's also full. Which size is it? Just take out the holder. Because we will put the bits in here. First we need to open this up. And therefore you press the backwards button. And then you hold on to the black part of the drill machine. And open it up a bit by pressing the drill button. While holding this. okay so now you see it's widely open okay then you insert your holder a bit this side or this side oh no the dark smaller side put it in and then you press the forward button and hold on to the black part and then slowly let it close until it's tight just more until it's tight it's tight yeah now it's tight yeah then um because uh you see our uh screws are like a cross yeah have a like cross slit Just open this up and select a bit in here and then when it clicks it will be secure Thank you. yeah so which this this side this pull out is backward so this is pull out this forward yeah so yeah backwards no So it's hot. and just draw a line here and then i'm also marking where i want the holes to be here and here you can do the same thing okay so first the draw the line here And so it's random or we put it at a certain place? Here, this too. Maybe you put them a bit too close to the ends. It's okay if they are a bit more inside. yeah yeah so this part and this part yeah okay um now um probably have to do it again but we have to prepare the surface of our uh wooden side with the sandpaper first yeah um to make it a little smooth Oh, okay, yeah. The surface is kind of smooth and also the markings are not gone so that's good. this edge where we are gonna attach our device. So we just take it, maybe with both hands. Continue with here, this, and this edition. is that a right or yeah this is perfect okay yeah so we marked the line here and what i want to do is i also like um saw it with this um border I don't know, like, it could be that some of them are a bit dull. Yeah. But we can try. Here's one more. Here's one more. You just... follow this line just follow the line align the saw with it and then start sawing like a bit slowly at first because there's no line so when you have a line then you can go a bit faster so how deep should we solve it how deep should we go here you can just orient yourself with this line okay yeah so it's probably this this one is a bit much but just just like this okay of this folder. Okay. Now you have to kind of like two lines here because you already started doing it. Yeah. Yeah, the difference is the second line. Let me try using this song. It looks like this one is a bit dull. Did I follow the right line? This part is a little bit right. Just use this thing. Okay. Yeah. Yeah, it's a little bit to the left. There's some. Okay. Okay. just mark the drilling holes like this so we can place Now you just put your glass here and align it with the holes you just punch. of them in their hole and then screw it just slightly oh yeah of course we will need to press the yeah okay but don't just screw both of them like all the way yes the first thing you'll go a little bit so just a bit yeah Yeah, it's fixed. Okay. Mm-hmm you have to watch out for this okay this could be too small yeah Okay. No, the... So, perhaps it's not fixed 100%. Yeah, it works. You have to, like, really lean on top. Yeah, okay, okay. And I'll do the last one. Yeah, that's fixed. I know, that's fixed. So now it's successful. Now, where's this pencil from? Pencil was on the table next to the charters. To the charters, here. Yeah. Then we have to disassemble our driven machines again. So you press the button for pulling out. Hold on to this. Only the black part. Only the black part. Okay. Tight, and then press it slowly. Now you can pull this out. And then remove the battery. Press the button and slide it. We will have to charge our batteries again. And if there's a sound that means it's charging. To pull this out. Yeah, just slide this off. Take the drill bit out. And take out the drill machine. Where's the box? Here. The holders. This can... The last thing is we can clean up a bit. Okay. Just swipe off some wood. Wow. Yeah. Fix. Yep." + } +] \ No newline at end of file