diff --git "a/2_Inspection_Repair/narration_transcript_inspection_repair.json" "b/2_Inspection_Repair/narration_transcript_inspection_repair.json" new file mode 100644--- /dev/null +++ "b/2_Inspection_Repair/narration_transcript_inspection_repair.json" @@ -0,0 +1,332 @@ +[ + { + "category": "inspection_repair", + "name": "User_1_407_2010_4_480.mp4", + "transcript": " I'm going to inspect this Mac computer. First, I'm going to attach the power connection just to see if everything is working fine or if there are any issues, any clear sense of problems. It's the connection plugged in. okay so it did not start so I think there's definitely a problem that I need to solve and I also see that these screws are also not put in perfectly so I think first I'm just going to put this onto the table and the first thing I'm going to do is just fasten all the handles so that I can operate this with more ease and also be able to move this without damaging anything okay The rest of the setup looks a bit problematic because I can see some clunking noise from the inside. I'm going to open this carefully. and also open the lower parts it seems to be a bit jammed okay Press on this button and put this up. And open this up. You see that some parts are already old and some connections are disconnected. So I think the first thing I'm going to do is just grab something to clean the thing. And I also see that there are these screws that are floating around freely which should not be here. Along with this old rubber band. I'm just going to take it off with my hands. I'm inspecting if there are any loose parts where screws should fit. There's another screw that is also loose and perhaps could be attached somewhere. No I don't think so at the moment So then what I can do is start connecting some of the cables here Carefully plug it in. Same here, this is not plugged in fully. And this, these two can also be plugged in. Okay, just inspecting the graphics card, the RAM card. Placing it carefully and attaching it. It should sit comfortably and perhaps the same on this graphics card front. It should also be sitting quite flush and i think it's it's all right looking at some missing connections yes this should also be plugged in so one carefully plugged in same with this okay the hard disk is also connected I guess with all these things fixed I can test the setup again but Before I do that, I'm just going to close this up temporarily. So I don't cause any unnecessary open issues with the power connection. And now that this is done, I'm going to plug this in again. And just try and restart the system. OK, so it starts. OK. alright, so I'm going to turn this off and then detach the power connection once again open this up to ensure that there's nothing left unnecessarily it seems everything is okay and there are also no loose screws here uh just checking if this should be fit somewhere but i don't think so I don't think so either. So in that case I'm going to close this up and attach everything. These are additional screws that did not fit anywhere. Going to fit this in. some of the lower parts and this This one seems to be fit but it doesn't connect that well or is it a bit loose for some reason. Okay, one fun test. Okay. so this is how I know that it's actually working and all the connections are secure so I'm going to shut this down again disconnect the power connection also from here properly put this aside through the unnecessary things and put the computer back on the trolley to take it to its original location also keep this secure The repair process is complete." + }, + { + "category": "inspection_repair", + "name": "User_1_410_2310_1_480.mp4", + "transcript": " I'm gonna try and connect this and see if this is functional open this let's check so i'm getting a system error which i'll try and resolve first turn this off the cables i think the first thing i'm going to do is just um get rid of the handles maybe or let's try and open that up let's remove these screws also lay this flat on here carefully also get rid of this Now that this is off, I'm going to open up the panel and start from here. And here. I also need to remove this I should slide and kind of detach this I'm going to remove this as well. I'm trying to remove this. Okay. and this graphics card I think needs to be replaced so I'm going to take this off I'm going to put this here for the time being and sata zero is at here and the power cable is also here okay so the disk is connected i'm going to try and fit this and also this as the board so let's check if we can make this happen just gonna fit here perhaps and also fit here okay um the ram chips plug it in again and if it fit correctly okay it did not Let's see if it aligns. transfer it in the other slot maybe okay that looks slightly better alright Now for this, I need to screw this in. I don't have an extra screw, so I'm going to use this to hold this in place. Use the magnetic one. and then i'll try and attach the graphics card but it is again hindered by the band here so i'm gonna try to see if i can do this first okay this is inserted the power supply is also working so I can temporarily try and close this in using one of these just put this into place for now and then let's it's open but I'm gonna try and test really quickly if it is actually helping at all the changes I made I'm just going to take an image of this to make sure that I remember to process it. Okay, so I'm going to switch this off. I'm going to attach the inputs to the graphics card and test again. There's general response. first of all unplug the power connection and also the VGA display and then let's try with getting rid of the graphics card I'm having a direct connection there. All right. I'm going to plug this into the motherboard. okay and i'm gonna try next is just uh maybe see if that made any difference and maybe also just change the ram back to the original location i don't know if that was the issue Let's do a quick test. Plug this in. Plug in the VGA. Other way around. And switch this on. Uncorrectable PCI error. now let's see if getting rid of this and adding the graphics card in makes any difference i don't think it will but Plung this in. And holding this in place. Using the screwdriver on the screw. Okay. Now we can do a quick test. Maybe let's just try here. Give it a minute again. the same error again so turn this off and I'm just going to google it okay so i'm not sure i don't think this is going to solve anything no it did not work I'm going to then remove the graphics card and also Take off the RAM chips And can I unconfigure this? Can I get rid of this? I'm not sure. But I think we'll have to repair this and do it later." + }, + { + "category": "inspection_repair", + "name": "User_1_410_2310_2_480.mp4", + "transcript": " I'm going to assemble this computer and the first thing I'm going to do is just inspect and see if everything is OK and if there are any loose parts. So this is a loose part which might be needed to be tied in. And then I can just start connecting the different cables carefully. Connect the fan. connect this carefully okay now I will connect the RAM chips and go here connect the graphics card also close this open port here for which i also need a screwdriver and a screw so i'm going to close this and hold this in place and also use this perhaps to hold this in place that is tight there are no moving parts and they should be held in place because of the plate that I have down here the SATA cable I believe It doesn't really matter, but let me try this. Wrong configuration. Okay. Okay, connected. It's also well connected. then i will leave the panel hey Thank you. Align this and yep. Mm-hmm. Okay. Yeah, right now. The process was successful." + }, + { + "category": "inspection_repair", + "name": "User_1_451_2501_Repair_1_480.mp4", + "transcript": " I'm going to repair this PC and inspect if it works correctly. First, what I can do is plug in the display and the power cable and check if everything works. Plugging on the machine and switching it on. and plugging in the keyboard the monitor should be on switching on the monitor I see some instructions on the screen that there's a invalid configuration information so I'll try and see if I can just continue no and if I get the same error then I will open it it's booting up the instruction is that there is no boot device found so I'm going to switch it off and I'm going to unplug the cables and also the monitor and I will open up the cabinet carefully laying it down opening the hatch and the door is open and i have these set of instructions with me in case of i need something to refer to so i've already tried and uh practicing on the computer so it did not work and checking in the power unit it's connected properly and the next is the cmos battery also seems to be plugged in well and the fan unit is also connected making sure that the cable plugs are well connected to the motherboard the ram Closing these hatches. I see that they are connected also properly. The hatches are closed. Properly adjusting it. They're well closed. The next check is for the hard disks and I see some inaccuracies here. This hard disk is not connected to the motherboard as far as the data cable is concerned. So I'm going to take a replacement cable and carefully place it. aligning the ends and replace this and connect it to the motherboard here so this is connected and this the other hard disk seems to be connected but I don't see that the CD drive is connected to the board either so I'm going to connect the CD drive to the motherboard Putting in the data cable and plugging it in. Connecting to the motherboard. Connect it. the next thing I see that there's a solid state drive SSD which is loosely mounted it is not fixed but it is not properly it should be connected to the motherboard and I mean should also be installed so I'll see if I can mount this and using the Slot that I have here, but these slots are missing. So this is appears to be damaged Let me check if I find a replacement for this And if I would be able to use this as a replacement I'm going to check screw falling down so try again so this end is connected so i need to take care of this end probably let me check if i can indeed reach this end It seems that I'm here, but I don't know if that is enough. I wonder if I could insert the SSD in this fashion here and then attach the screw on this end somehow. from the outside because even if I insert the drive as it is right now it would fit quite loosely first I'm going to take out these cables so that I can access the port more comfortably I'm going to try and see how the SSD fits into the slots Yeah, I can see it is held extremely loosely. But my question is if I remove this, so this flap should not be a problem for the flap. so I'm going to unscrew this bolt and take it off first and see if I can maneuver it and install this bolt from the outside once the SSD is fit in putting in the SSD Let me see if there's indeed a opportunity to align the slots in any way. Probably, but it is too much of a mismatch from this side, I think. There is too much of a it's too rigid in terms of the fit I can test once anyway but it is not likely from my perspective that it's going to fit picking up the screw using the magnetic screwdriver it appears to be stuck in the slot and that is inconvenient because it won't budge. I'm going to use this tool to try and remove it. and once again try to fit in it once again fit in the wrong direction and it fell so I think fitting the screw from this direction is going to be very inconvenient Let me see if I can align with this upper slot somehow. Which could be more convenient. It's from the outside. It will not go in from what I can understand. is quite uh superficial it did not go in properly so i think the best remaining option is to fasten the bolt here and let the solid state drive ssd be Loosely attached here. Now since it is Okay, because it's not mounted like a HDD hard disk drive, I think it should be still okay because It won't be Facing any issues because it is not really gotten any moving parts I believe so I'm gonna plug in the power cable and i also need a data cable and i'm going to find a slot first of all just this and align the cables but i think this is a inconvenience because this is angled so i'm going to fit this first and now for SSD I believe it needs to be like this oriented and it seems to have fit just okay I'm going to attach the power cable for the CD drive and the CD drive also needs the data cable just this seems to be attached just fine so after that is done cd drive should be functioning i can tighten this bolt it seems to be tightened already we don't have any zip ties from what i can see so i cannot tie them up and now i can do a very quick check if we face any immediate problems when i try to start the pc cd drive work click on the cd drive button and it seems to work okay so i'm going to switch it off switching it off disconnecting the power cable and now i can close the hatch first i can take this clock and clean up the area make sure there are no loose parts or nothing hanging i don't think so and also make sure that the floating ssd is able to sit here quite comfortably without disturbing any other components or any other parts that's also seems okay to me I will close the hatch carefully this cable seems to be a bit problematic I have to check and now I'm going to connect everything again including the display and aligning this and fitting this in and also the keyboard in case of an input and switch this on is it booting up i don't see any display output Let's see. And onboard diagnostics. And I see that the hard disk drive. All the other drives are recognized. see some noise coming in from the fan I can see on the test CD drive seems okay configuration is testing whether the hard drives are okay and hopefully they've been plugged in just fine and based on the test so there's a problem with hard drive 2 so i'm going to cancel the test and i'm going to exit hard drive 0 was not a problem but hard drive 1 was never tested on hard drive 2 is problematic based on this I'm going to switch off the computer again and plug out the cables I may need to take a better look at hard drive 2 and the connected hard drive properly laying it down opening the hatch these are the two hard drives and seem to be connected just fine I'm not sure what the cause of the issue was perhaps the hard drive is damaged in some way closing the hatch again plugging in the cables and the keyboard I'm going to try and continue to see what happens and based on the instructions I believe I've followed pretty much all of them but the system failed to boot because of a incorrect configuration of the hard drive for some reason okay so I will switch off this computer and note down that this PC repair was unsuccessful because there seems to be an issue with the hard drive and one other test that I can perform is to see if I can remove the hard disk and be able to boot the device successfully because i believe that this hard disk may be unnecessary i can check but the concerning thing is that that the error node boot device found suggests that there might be there might be some other issue but I don't see any slots for any other hard disks or SSDs here so i'm going to close the hatch again and if that doesn't work then i'll take out the other hard drive and try plugging in the display cable and the power card and the keyboard switching on the PC and waiting for the display to show something okay looking at the on-board diagnostics again and this time hopefully there should not be a problem with hard drive one if it is then i would know that the hard drive that i'm facing issues with is indeed the one that i did not disconnect look at the diagnostics no problems with video card usb devices and the boot path also seems okay so I hope that the hard drive one test also passes The fan speed has gone up. There's an issue with hard drive one. So the one that is connected is the problematic one. Trying to exit. exited and now I'm going to switch it off removing the cables and I'm going to open up the hatch open up the cabinet and change the connection so that i don't connect this hard disk removing the power cable and the data cable i'm going to connect this hard disk instead and see if it makes any difference plugging in so this is completely disconnected and i'm going to close the hatch and try again plugging it in System is booting up. and i'm going to run diagnostics again to see if there is indeed a problem with the hard disk again this time and i can see that maybe it's taking slightly longer this time now it worked i don't see os boot part one i think which was there before if i'm not wrong so boot path 1 might be in the hard risk that I just removed and the test is happening and looking at the hard drive test and the motherboard fan being tested The noise of the fan is still elevated. Hard drive one is okay. So the hard drive that we just tested seems to be okay. Now the CPU is being stress tested. Waiting for the tests to finish. I'm looking at the expected states and I believe all paths now did not there was no critical issue at this point and they're being tested again okay and we're at 82% so the fan noise has reduced from before and this is taking longer than expected the ongoing four core tests should end soon but there's a new test happening now system memory is the last thing that is remaining and the boot path also seems okay so The system is not set up configured properly. In that case, it doesn't work. And we have moved into the 90s. and looking at the total configuration I can see that it is still quite slowly hopefully it ends right away and it still won't still won't finish put small parts back into the tray clear the table This should be one of the last tests, I think. I'm going through all the blocks and the next blocks are much faster. and this last one is much slower at 20 and look at these temperature values here CPU thermistor is running quite hot currently because of the test and hopefully I should be able to proceed further after this test and now uh anything i need this i'm going to place this down no problems have been found in this system so far uh it may take 30 minutes or more it is recommended so i'm going to run the tests and hopefully the system boots up" + }, + { + "category": "inspection_repair", + "name": "User_1_1910_repair_480.mp4", + "transcript": " I'm going to install this graphics card on the computer. So first I'm going to just carry the computer here on the work desk. Use this trolley. Carefully bring it in. Place the working computer with the handles onto the desk. Upon investigating, I see that I also need cross-head screwdrivers which I should be able to get from here I don't have cross screw hours here so I'm going to search in the other lab You can use this and get started. Just place this here. Raise the position so that I don't have to move this substantially. pretty much level, so I can start by placing it here. Actually, I can move it slightly away. Upon investigating I see that I don't need this at the moment Lock it in again. We can start from here, perhaps. Can I remove this and remove the shell without removing the handles is my question. And probably not. I'll lay this down. Observe again and ok so graphics card is currently fit here this and if I want to fit this then I will need to remove the panel and remove this and make some adjustments here ok so I can start from here and i can remove this by lifting it up and this is held into place currently so i don't need i need this and i'm going to place screw here and if these two are identical they are not so keep them separated so this here So this graphics card is out. Before fitting this, I could actually clean the inside space a little bit. OK. And if this should have been plugged in If I do then I won't be able to adjust and attach the Rest of the thing, the assembly. So I need to take a look again at how this is going to fit here in this space. Move this out and try and adjust this. And I see that it can be attached. In which case, this is not really usable. Remove this plate." + }, + { + "category": "inspection_repair", + "name": "User_2_407_2910_1_480.mp4", + "transcript": " Okay, first I'm gonna put on the working gloves to start the repair of this demonstrator sub-assembly. First thing I'm going to do is detach this plate because this will belong on this rectangular frame. I will need an Allen key for that. and I'm gonna put the whole thing up again and rotate it like this so basically the rectangular frame is correctly positioned already in the middle bar here too now what I can do is I can reattach the plate here. I will need four screws for that. I have two here. And probably this will have to go here. So I have to attach it like this. so here for the hole to screw in the bolt same goes for this one apparently there is no I can remove this plate here and get one of this out. Reattach this and put this back in here. So now I have four pieces to This was the wrong approach. I could have just flipped. the plate. I thought it was symmetrical, but it's not. So I don't need a hole in this bar. I can put both of them into the side bars. Okay, now I can tighten the plane. okay now all four bolts are tight and next step would be detaching this short bar because this is wrong um i will leave this here for now so yeah those two bars they belong with the the side here and that's why i'm gonna detach them also watch out here hold it so it doesn't fall okay leave it here Okay, so I detached this. This will go back here. What I can see is there was no knob like this. The knob belongs here. So I'm going to detach this now. Okay, I'll need a bigger Allen key for that. And... Yep. for that I'm going to need those pieces so here's already one I can use and here's also another one I'm just gonna put it in here And now we can attach it with two bolts. I'll try a shorter one. I'll try to align it with this line in the middle. Because I think, oh no, okay. In the picture it looks like it's like right on the edge here. And that's why I didn't screw them in all the way. To readjust the whole thing. Okay, so now it's tight. And it's positioned the right way. I'm going to do the same thing for the bar on top here. I'm going to remove the bolts and then I'm going to need two more holes for the bolts I'm going to take them from here and slide them in this trigger Take two bolts again. Put one here. Tighten it slightly. The other one goes in here. You can also tighten it slightly. Okay, I position and line it with the edge. And now I can tighten both of them. This, okay. Yeah. So, this needs a cover. Put the cover on. There is a cover here. I'm just going to use the screwdriver to handle this back on. And the last step is only with this bar. Attaching this here. And also the knob. Alright. So I think I'm gonna need this. And I will also need another hole. where do i get one okay first i'm gonna attach the knob Okay, it looks like it was aligned with the edge too. That's what I'm going to do. Tighten it a bit more. And then just need to attach it onto this bar. But apparently that is" + }, + { + "category": "inspection_repair", + "name": "User_2_410_0210_1_480.mp4", + "transcript": " So in this recording I will be disassembling and reassembling a projector for inspection. And first I need to turn on the lights for better vision. I will get the projector out of this wardrobe over here. that is the device and the cable for the projector I'm gonna bring it over to my workstation and place it here at first what I can see is that the lens is adjustable for focus functions with those two levers here. Here's the cover to cover up the lens. There's some manual buttons to control the settings. On the side we have a handle that can be extended for better transportation. Underneath we have four legs. Those two legs, the blue ones, they can be adjusted by pressing the button. So this is fully extended. This too. So that the projector can be placed like that, angled above. down here um they're also like uh those legs are also adjustable kind of this one is broken already um but yeah i will leave them inside for my disassembly task i see that i need um a crosshead screwdriver for this task um and I'm gonna look for them in this drawer. That is a cross-head screwdriver in this tube. I will look which one fits into the screws in my case. It looks like the bigger one can be used for everything. I will start with unscrewing this screw to take off this component. It's still a bit tight. I'm gonna angle it so it goes off a bit easier. I place it over here. This is the flashlight component. I can take that off with unscreen. the two screws here and then getting off this handle to pull that whole thing out here we can see the flashlight so this is like the main compartment for the projector so Yeah, this looks good. I'm gonna put it back in again and just slide it in here. See if it fits. Tighten the handle again and then tighten the two screws for the flashlight. Now I can put back the cover for this again. And screw it back in. This component is just the fan and filter for the projector. I'll place it back in place. and tighten the cover part. Okay, the next thing I can do is remove those three screws here. This is the first one, second one and third one. To be able to take off the enclosure of the whole projector. So this is loose. this is also loose and the last one also loose um so those are the screws for the top enclosure part but there are also two screws for the for the front enclosure here which i'm gonna remove now that's the first screw i'm gonna place it here and then there's this screw you can also place it here And now I can remove the enclosure. So the three screws for the top enclosure just fell off because I loosened them. And this one I need to get out of this little slit. So those are the screws I removed. I'm going to turn this over and remove the enclosure. This goes off pretty easily. That's the top enclosure and here we have the front one which is still connected so here's the fan I can disconnect it to inspect the enclosure I'm gonna remove those cables too like that so here I can see the mechanism of adjusting the legs by just spinning them I can adjust the length so that I can control the projector and where the projection will be depending on my table and other things okay so this works fine in here I can see here's the lens and that here it is adjustable yep this looks good and okay everything looks fine in here so what i'm going to do next is just reassemble my projector again and then see if it works I'm gonna get the legs out so I have more space for putting back the projector again. I have to put back in the cables that came along. So I have to pay attention to put it back in correctly. See that orange is on the same side as the other orange cable. Let's put back in the cover. here and the top compartment here's this cable i can put here it's a bit loose but yep so Now this is fitting. What I can do now is put back in the three long screws. and also screw in the screws for the front enclosure tighten it so this is already tight I'm also going to tighten three screws for the top enclosure. So those are a bit longer screws. This is tight. Also tight. and the last screw here this is also tight now put back the cover of the lens and then i'm using the cable and finding a a spot to plug it in and then i can put in this cable and see if the projector works okay it looks like um there might be a problem with the power supply um but yeah i'm just gonna put back the projector with its cable into the wardrobe closing up my wardrobe Then I bring back the tools I used. Clean up the workspace a bit. And that was the disassembly and assembly task." + }, + { + "category": "inspection_repair", + "name": "User_2_410_2409_1_480.mp4", + "transcript": " So in this recording I will be disassembling an assembly table which is located in another lab. And I will take this trolley to transport it to my workstation in this room. First I'm gonna leave this room and take the trolley with me. so now i will be transporting um this assembly table to my workstation and then i will disassemble it just like this this table can be lowered and heightened with this lever thing I will adjust this to the highest setting so I have the shortest distance to the screws I'm gonna unscrew For those, I'm gonna need the Allen keys I prepared here. And the black bolts, the black screws can probably be unscrewed with this size. Yeah, and that's what I'm gonna do now. just untighten them a bit with this side but i can apply a bit more force and then when this is done i can use this side to make it a bit faster that's the first one that's what i'm gonna do with all the dark uh with the black bolts just like this so those are the four on this side but there are more here and that's what i'm gonna untighten to i'm gonna untighten all of them and then remove all of them at once There's much force needed to unscrew those. Okay, so unfortunately what happened here is that my allen key destroyed the inner structure of the bolt so now it is not possible to remove it with the allen key but what i'm gonna do is just remove all the others and see how far i come so all screws so yeah normally this could have been removed now um but unfortunately there's this one screw over here that i cannot unscrew anymore I'm gonna try again okay it still works just wasn't deep enough and you can work with this so just like that oh yeah okay so to remove the upper part i need to also remove the lever i'm going to place it over here and now i can remove this thing and i have to see that the legs will not fall to the ground i push the trolling over here so that i can bring this leg into the wall over here so there's still some kind of problem to remove it then i think i need to remove those screws first this one's too big and the smaller one which would be this tool here yeah this works So this works and then I'm going to do the same procedure with every screw. Two screws on this side and here are three left. Those are a bit more easier to remove. They are not as tight as the dark ones. oh okay so what happened here is when I unscrewed the second to the last screw this thing over here was only secured by one screw and so it fell down but what I can do is just hold it here remove the last screw with one hand and then remove the whole thing just like that exactly so i have to correct myself there are like three screws on every side so now i'm able to remove the upper part from from here that's how it looks from the inside I removed all those screws I'm placing a single part over here and now what I can do is inspect the mechanism of the inside probably the lever somewhere here okay so it's a bit oily um yeah the lever was here and now you can see kind of how the mechanism of lowering and heightening the table works Yeah. Exactly. Okay. and that's what I wanted to achieve look at the inner mechanism I'm not gonna disassemble more of this so I'm gonna start assembling it back together now therefore I need to remove the lever again and put the upper thing middle piece on top now I'm gonna put in all the screws back again or what I'm gonna do is also put this thing back so doing this alone could be a bit difficult I'm gonna try This was not the Allen key. I'm gonna look for the needed Allen key now. oh i left it over here so this fits with those smaller screws and i'm gonna put them back in two knots so that i don't need to like walk over here every time i'm gonna place my screws here I'm gonna see in the room next door if I can use an electrical drilling machine. I'm looking for an electric drilling machine with a fitting bit. but I think there's not one that is small enough or fits into the screw so this is not gonna work Here's something I can use. Those, but they are too big for my use case. Yeah, so I am bound to doing it with a manual Allen key. Gonna lock the door. And go back to my original workstation. Okay. Then we just do it by hand. Like that. It's a bit difficult, but that's not gonna be a problem. I'm just gonna move it back here to have a bit more space. And then I'm gonna try again. And I'm gonna sit down maybe for this task. Make some space. yeah like this um and then where was the screw again it was right here i'm gonna take all of the screws and place them here too yeah so this is in there first screw i'm gonna leave it hanging like that at first then go to the other side and take a god yeah so it looks like i I place the screws there and kick them or something. So I have to look for them later. There is also no problem. okay so this is tight to secure the whole thing i'm gonna continue with screwing in the outer screws like that okay i think i found all of the missing screws already so don't have to worry about that anymore not tighten it too much because we need to adjust like it's better to adjust all of them at once so you can still move it like this to align both holes and the last room can we put in here seems a bit difficult i just have to adjust the metal piece to align the holes screw it in and then we're good to go gonna try by hand first you can have more control yeah i think it's in there now just need to screw it a bit more okay now we can fasten all of those yeah and the outer thing is still movable so that we can also fasten the last kind of screws the dark ones okay so this is tight and this is also tight But yeah, like in the beginning this wasn't even that tight at all. So we don't need as much force as the other ones. Yeah. So for those, I'm going to go back to this bigger Evan key. Yeah, this one. and we have one two three four five six seven eight screws and four holes on each side so now we have to see where all those holes are gonna be now okay so i think what is happening here is this here needs to be in there so that we can actually see the holes okay on this side it looks correct actually but here Okay, I'm seeing the hole over here, so it has to move a bit in this direction. Like this. Something is blocking our way to move it. And I think maybe it could be the screws. okay now we have it yeah aligned and now just fixate the position with screwing maybe by hand first this and yeah. I'm going to try screwing all of them just a little bit so we can have a fixed position on every side. But this looks good already. Let's see on this side how the holds are aligned, not quiet. Yep, so this is in there, in the hole. Tighten it a little bit. Okay, something's in the way here. It's in there. No. Okay. Something keeps us away from actually screwing it in. I don't know what it is. This works. this is also in the hole and then i can put in the last one and then tighten all eight of them and then i am finished with the reassembling and then i'm gonna Okay, this looks good. like that and then switching sides again to tighten a bit more so here i have a longer lever so i can apply a bit more force to it so it's maybe comparably as tight as it used to be all right this is already tight this too yes perfect so this is good to go again last step would be putting in the lever on this side so I can lower my table again." + }, + { + "category": "inspection_repair", + "name": "User_2_410_2709_1_480.mp4", + "transcript": " So I'm going to get a Mac PC and disassemble it and look at the inner parts of the device. At first I'm taking this trolley to transport the Mac into my workstation over there. This. I'm going to work on this table here and therefore I'm lifting the Mac PC onto the table. At first I want to remove those screws with an allen key to remove the handles and inspect them. So I have two allen keys here. This one is too big. Therefore I'm trying this one. And this one fits. So I'm removing this screw. And here's a second screw for that. So I can remove the handle and place it here. Then I want to remove the second one. It's over here. and now that I removed those two screws I can remove this handle I'm gonna flip the PC to be able to remove the other two handles I removed the two screws and therefore I can remove this handle. So this handle looks slightly different from the others because it is one of the bottom handles. And the last one. Okay, so I removed the handles. Now I can continue with removing the four screws on each side of the PC to try to remove the plastic cover. okay so it's a bit hard to remove the cover because it is still attached to the middle thing there um okay i don't want to break it so i just leave it like that um Yeah, is there way too... No, okay. I'm gonna flip it again. Okay, so this handle just came off. it's not over here and this would be secured by those handles but I removed them so I can just leave them here so those are the bottom ones and here this is also a bit hard to remove but yeah I can continue with those screws for the front cover. Okay, so I'm thinking this would be the same as in the bag. Hard to remove. So I'm just going to leave it like that. Yeah. Alright, okay. So what I'm gonna do next is I'm gonna open the PC to look into the inner parts of it and inspect them. Therefore I'm using this lever and pulling this down. And now I can see everything. um the first thing i'm gonna do is i can remove the small battery here this um okay i'm seeing that i need i can use my allen keys in here to remove things i'm gonna get a screwdriver from the room next door so the screwdriver has the right form and i'm going to use it on the screws over here so i want to remove this plate remove the screw here leave it on this side I just need some. Yeah. All right, so I remove this plate. What I'm gonna do next is remove those two screws to look at the fan here and here so the screws are a bit longer so we don't want to mix them up here and this one here So now the fan can be removed. It's quite dirty and old. I can also remove those screws to see if I can remove the outer rubber part. Now we can add this fan and exchange it. So there's another screw here, and I don't know what this is. I'm gonna remove it for inspection. So this is the cable here is attached to the device so I can't remove it completely but it looks like the LAN port. Use the screwdriver to put the cable back into the um, securing, holding, uh, over here. Yeah. This, I'm just gonna place it here. Slide it into its place. Yeah. Um, next thing I can remove is I believe I can remove this box over here therefore I need to remove this screw this screw yeah This and this one. I'm going to start here. The screwdriver is magnetic so I can pick up the screw with that. Leaving it over here. and the last screw is under the box 4 screws now I can loosen this and get it out for inspection so this looks like the um cd reader okay i'm gonna leave it here at first because it's still attached to the cables in the back I can also see if I can remove this outer metal part of the power unit here. I'm going to try removing the screws for that. Leaving it on the right side. Okay, this is a bit hard to reach. Yeah, it looks like this. Just slow and steady. Hello. okay so one screw just fell down here i'm gonna look for it after i removed it okay so the second one also fell down here it's right here But there have to be four screws for that in total. So there's one missing. I'm gonna look for it here. I think... just remove this first okay there's one screw left here Yeah, now I could remove this metal piece. Interesting. Okay, I still need to look for the missing screw. kinda disappeared somewhere okay so this screw is probably for the fan over here okay it's somewhere but that is no problem we can just continue okay so yeah so now after inspection i'm gonna start reassembling the pc again and i'm going to start in this area with the land port now i'm gonna put back the fan again and the outer rubber part must be secured and tightened first with the longer screws here now it's tight and I can put it back and I believe that it must be secured here. okay so i'm looking for the holes where i can put them back in again but this doesn't look right i think it's okay so i think i put in the fan the wrong way because the cable is a bit too short to um this so i want to put it here i have to put it back in like this And then place it right onto there. Like this. so later we can put it in like this but before I can do that I'm securing the fan in the rubber holding piece like this putting it here and Put back in the screws. I'm recording right now. Yeah, no problem. But it's from the motion capture room for me. So now I put back in the two outer screws for the fan and now it's secured and it can work properly again. so now that i'm finished with this i'm gonna put back in this plate i believe it was orientated like this so i can put it back into its place okay so for that i will need to apply some force But we still don't want to destroy the device. Yep. Click. So it's in place again. And I'm just securing the screw up here. All right. next thing I'm gonna do is I put back in this metal piece here and because later I have to put in the screw in here I think to secure this so I'm gonna start with the two screws in the back one goes here I'm not tightening it completely so I can just still adjust it a bit if it's crooked or something in the end. So this is the difficult hole. But I think I can still do this. It's not easy. to be seen, but now it's kinda tight. Two more screws here. One is down here. And the last one would be here. And normally there would be one here too. I lost it, so I'm gonna leave it. here somehow it doesn't really fit to adjust this here Okay, so I'm trying to align the two holes to be able to put in my last screw here. It doesn't work. Maybe I have to untighten this even more. Now it looks like it could fit in this hole. It's getting tight. I'm just going to leave it like that. Because as long as it's secure, it's good. Tightening the other screws now. And the last one here. This is tight now. So what I can do next, at first I'll close the door again. Now I'm putting in this, I'm putting back this box. yeah now it's in place the holes look aligned and there are four screws i'm gonna start the one here i'm doing the same mistake i'm leaving some space to adjust it then i'm going to tighten it in the end Then here's a hole, here's a hole. And one hole down here. Tight. Finishing off with tightening this. And this screw. Yes! That is done. What is missing is the battery here. Just put it back in. And now the inner parts are all back in place again. And I'm going to close it up. And the next thing I can do is put back in the handles. The top handles are here. And they're secured with two screws each. and therefore I will need the allen key again and not a normal screwdriver yeah My first handle is back in place. to align the hole to put back the screw to apply some force with my left hand to be able to align this Okay, I'm switching sides of the allen key to be able to apply a bit more force to make it tight. But yeah, now the two upper handles are in place and I'm going to continue with the front cover. So I'm gonna need to tighten four screws on each side of the PC. Mm-hmm. This is tight now. I'm gonna flip sides, switch sides, and doing the same thing on the other side. Okay, so tighten those screws and I'm gonna flip the whole PC upside down to do the same thing here with the handles. Here I can put back in those bottom pieces, I believe. I put back in this piece and this side because it has this structure which only fits here and here it doesn't fit because here it must be here. So this thing, the even part of the handle must be facing outside. So in the end I can just flip it again so it can stand on this even space. okay so this handle is tight now this part has this cross structure on the left side here which fits right into here and then i put back the handle" + }, + { + "category": "inspection_repair", + "name": "User_2_411_2410_3_480.mp4", + "transcript": " okay the task is now to repair this windows pc um at first i'm gonna check if it is working or not therefore i'm gonna plug in the power cable and this is here in my toolbox plugging in the cable so the fan in here just moved but i can't see anything happening on the monitor Um, yeah, of course I have to plug in the DVI K2. now something should happen but i can't see anything on the monitor meaning i have to repair it and therefore i'm gonna plug out all the cables and then open up the pc here i can also use a screwdriver and the rest can be done by hand okay so i'm gonna check um what i can do now um so the first thing i notice here is that the hard disk is not inside and that's what i'm gonna gonna put back in now here are some things i can so therefore i'm gonna need a few bolts to to put back the hard disk but I'm not sure how to attach this I mean down here there is already a hard disk so probably this one doesn't need to go inside I think yeah so for now I'm going to continue with something else and then see if it works or not here's a CD drive the loose cables here need to be reattached in Checking if the power unit is connected to the motherboard. Yes, it is. Check if the fan unit is connected to the motherboard. I'm going to remove this. better view into my PC so the fan is not connected I see but I can easily plug it back in here like this the cmos battery is connected let me see if i can reconnect those cables here let's check the picture this probably can't be connected here we have something that looks like it belongs somewhere so so the graphics card yeah you can leave it out for now because it's in the way for some cables that i want to reconnect mm-hmm okay then I can check the RAM chips the RAM slots for now there should be two in here I can only see one but in the box was one and i'm gonna reattach it here let's see how it probably like this is the hard disk mounted and connected so i'm not sure about this but it looks like we have to actually mount the hard disk here but it's too small i don't know how to connect those maybe like from here could be um let's see if we actually have bolts that fit in here this one doesn't this one does I don't think this one fits meaning that we don't have enough bolts for this and this would mean that this hard disk does not go in here but we still have to attach the loose cables here Okay, then I'm gonna leave it out for now. Make the power cable and the SATA data cables are those. where do they need to go is the cd drive functioning probably not because I mean there's a loose screw here put it back in but also you can check if it does something So the CD drive doesn't work. Meaning I have to connect some kind of cable here. So this is the data cable. Probably goes in here. Okay, now I'm going to check if the PC, the CD drive is working. Okay, it does. So that worked. Can the cables bundle together? the zip tie um those are already tight and here it's this is fine um okay yeah so the graphics card just remove the graphics card um also we can just go back in there's no reason to get it out I'm gonna turn it back on again and see if the things I did actually made the PC work again. I also have to connect the TVA cable. so apparently it didn't work the graphics card was also not attached properly okay I think I need to of course attach it down here the cable for the monitor to check if it's working now if there's Windows booting, this is fixed. Mm-hmm. so it doesn't boot completely um maybe i can check if there's a step missing System battery is dead. Hmm. the problem is those cables are still loose i don't know where they belong could be here like for the cd drive but this one is still loose and it doesn't fit anywhere there's also a SATA cable this doesn't help I can do is I can At least tighten the graphics card. One screw, just another screw here. Now let's check if it's working or not. Okay, there's still an error. Okay, CD drive's working. here's a loose cable here's also a loose cable but it doesn't reach any any other component of the pc this can't be attached There would be some kind of um metal pieces here i could reinstall the hot disk maybe but there's no such thing i mean what i can do is just place it here like that put this in Maybe I should turn off the PC first. so i mean the hard disk can be attached like this with the data and power cable but it will be loose in here and there is i could detach the whole thing here and see okay i can attach the hard disk Okay, maybe not there. I could have just unscrewed it here. The screwdriver doesn't fit. Hmm, okay, I know this doesn't help with the solution. let's just see if this will work i mean i can't see anything else that can be fixed here um Something about the CMOS battery. Not sure. I mean the hard disk is here and it is mounted and connected. okay so i'm not sure what i can fix you now um but i mean something is booting there's just a problem um okay i'm just gonna close it up Mm-hmm. Then I put baby one. okay so the pc is kind of fixed now and um okay on the outside there seem to be some loose screws those screws maybe this here here and here I think that's it. So the rest can go back in the box. And yeah, that's it." + }, + { + "category": "inspection_repair", + "name": "User_2_411_2510_1_480.mp4", + "transcript": " all right so what i'm gonna do is inspect and try to repair this pc unit first thing i can do is maybe just dust it Okay, so first I can check if it's working or not. Plug in the power cable and the monitor cable. OK, so it turns on, but then. OK, still something happening, but it turns off immediately. OK. I'm going to just turn it off then. And then we're going to try. Okay, so first I'm gonna open this up. Okay, so this screw kind of doesn't... Can I pull that a lot? I don't know why. But yeah, if I can't remove this screw, I can't open up the PC. it is loose so what's what's blocking here okay there was still some left okay i'm gonna check so here we have a hard disk which probably And go in here. Okay, and dust this too. I'll throw it in the trash. So here we have two RAM chips that I can insert. This is tight. And this one too. so do we have any loose cables so here is a new cd drives Let's see what those can do. Oh, I can open this up. here i can remove the cd drive um okay but this is not something that needs to be fixed so i'm just gonna reattach this I'm gonna lock those again. Just gonna see if I can put the hard disk in here again. Probably like that. And it's locked now. So here's a cable that's loose and I can probably put it somewhere. What I see, the CMOS battery here was removed. You can just attach it again by removing the fan first. Oh, yeah, whatever this is. i don't even think we need to do this remove it i mean so yeah just gonna turn this up again and put the battery back in here Let's see if this thing fits. I'm not sure. probably those beta cables Okay, so this fits in there. Probably right. So data cables are attached. The question is, can I also attach a data cable? Cut this open. Mm-hmm. so this is untangled and now i can take this whole thing and then attach it here on my drive and the data cable and the other cable can go in here okay so This should be touch. yeah what i maybe should do is put a zip tie around this thing here you just keep all those loose cables in one space and then cut off the loose end okay so i think that should be it let's try it out first Let's turn this on. Okay. Okay, so it started booting. yeah show some something on the monitor meaning that it should work now but i don't have any keyboard here so yeah but i think that's it so i can turn this off and close it up I'm just gonna clean up the workspace and put the tools aside that I'm not needing anymore. This can go in the trash. I just have to figure out how to close this whole thing. Was it like this maybe? Nope. It has to go like this. Yep. I'm gonna put the screw back in. The cover is tightened. The screw doesn't have to be super tight. I can just leave it like that. Now we have a functioning PC." + }, + { + "category": "inspection_repair", + "name": "User_2_451_2401_1_480.mp4", + "transcript": " okay the first step for this repair task is um just i'm gonna try if the pc works i'm plugging in the power cable and connect it to my monitor the light turns on but it goes out immediately so it seems like the pc is not working i will unplug the cables and then start inspecting the pc open the pc first and inspect the interior i'm going to place it down I'm gonna get my tools, the things I might need for the repair task. First I'm gonna check if the power unit is connected with the motherboard. so this is the power unit it seems like it's connected with this cable to the motherboard this this cable which probably belongs here so now this is connected then the fan unit have it here um which is not connected properly i can fix this real quick by screwing this i'm using the screwdriver i'll remove this first so i can place so i can position the screws easily like this now all four screws are placed just like one after another just screw it equally So this is tight. Now the fan unit is tightened up again. CMOS battery is the next step. This is going here. It's not connected. I'm just going to place it in the slot. um so i'm just looking for cables that are not connected to the motherboard so this is connected to the motherboard but not connected to the device looks like it belongs here yes ssd um just checking for other loose cables like this one perhaps This for the other fan goes in here. Maybe the other way? No. This is not loose so everything is in its place. um two ram chips yeah there are no ram chips in the ram slots here so i'm taking two ram chips from my toolbox and just place them in here open this first and the same for the other ram chip to this ram slot now two ram chips are connected hot discs mounted and connected so the hot discs are here this one does seem a bit loose but i can take the screw from my toolbox and screw it into this slot to tighten up my my hard disk this okay now it's not movable um it looks like this other ssd is loose this is a loose ssd um I think I can remove this and then place this inside this replacement. let this go together just gonna remove this and place this into into this um yeah like a compartment component um have to see how it's the right way to orientate it okay so it has to be like this so that the pins fit in the holes yes okay um and i just have to connect this And then put it back in. okay so I think this goes in here it's a bit loose though but I think this is the way to insert or maybe there's some kind of slot where I have to insert it no i think this is this is okay um cd drive is uh i already did that cables be bundled so i don't have zip ties here but the cables are also in its place and it doesn't look too chaotic so i don't need to bundle them together now i just with everything fixed now i will try um turning it on we connect the power cable first like this And it already turns on, which is a good sign. Okay, we'll check if the CD drive is opening. It's not currently opening. okay yeah the cd thing is not connected yet so i'm just gonna do this real quick um which it looks like. I just realized that this probably does not belong in here. Probably belongs in here. Like this. Yeah. I can also connect it like this. This fits perfectly. And then I can take this cable and put it into my cd drive which was not working before now we try again now hopefully it will function the other light turned on just gonna wait a bit yeah so i can feel some movement here so i heard something so in the meantime i can test if the monitor connection works somehow i cut myself but it's like a minor thing i'll just finish this task um Just see if the monitor is turned on, but I can see something happening on the monitor. to change the channel okay so something's happening the pc so it started and it's booting now yeah i think this is all right turn this off and disconnect the cable also disconnect the power cable and i'll just Place it like this. Let's see. Oh. So there's a loose screw. Just have to find out. Hmm. Okay. I'm not able to find the loose screw. But I will close the PC now because the repair task was done successfully. Just place this here. Just gonna clean up the working space. And then I can... Okay, so here's the loose screw. Place it in my toolbox for later." + }, + { + "category": "inspection_repair", + "name": "User_2_User_14_412_1110_1_480.mp4", + "transcript": " okay so now we are going to open up those two PCs and put in those two drives devices first I can turn on the lights for better vision and then we can push the trolley over here and lift the PCs up and place the components that we're gonna put in the PCs. Yep. And I will put my PC here. And then we can just do it at the same time and I will show you how to do it. So I can release the break from here. and push the trolley aside and then we can start maybe you can you do this one and i do this one just uh yeah you can just call it a component okay so at first what you can do is just open up those screws and open up But here, here it is just by hand. And we can get some screwdriver drivers over here. What are you looking for? Oh, one of the screws? Okay, now we can look for it. Do you see it? Okay, I found it. No problem. Okay, so yours is just by hand. I need a screwdriver for mine. i'm gonna unscrew the screws from my plate first and then i set the plate aside You can use whatever, you can use the green one. And we need to put those components just in this spot. But in my case, like all of them are already used, so I need to remove them. And to remove them, I need to remove this part too. yeah it's the same for you so you need to remove this one first and you can just use your screwdriver for that you don't need to remove those screws just this screw to get this plate off for me it is this screw here so i can successfully remove this plate for better vision you can just lift it up and take it off okay so like it looks like we have to put the device in like that and we also will need like two slots so i need like two free slots here yeah going down here and for you too but it also looks like you have to remove something you can remove this one here And I remove those two. Unscrewing the screw here. Yeah, and you can just unscrew the screw. I think it's enough if you have just like this free. So this fits in there now. We can do this. Removing this plate also. mm-hmm exactly the yellow part goes down and try to put it in the slot here okay let me see Okay, mine looks like it doesn't fit. Because this is blocking the way of my platen here. Or should I put it inside, like this way or...? No, yours also doesn't fit. like you see the structure of this can fit here because there's this black thing so this for this to fit in there this needs to be like like the constellation needs to be the other way around so um and this is also not possible so how i understand it there's no way to place this part in there let me see if there's another okay so for example this one looks like it yeah the black track here looks like it fits because like the small black hook goes here this one goes here And this one goes here. This one and this one. And you can also put those back. Now we'll do the same here. So putting back the disassembled components. Okay, I'm tightening the screw. I'm tightening the second screw for the other component. Is it aligned properly or not? Let me see. Not quite, I think. Let's go in a bit deeper. Okay, it's a bit stuck right. Mm-hmm. Now it's aligned and you can screw the screw in here. I'm gonna remove those screws to make space for my new component. gonna take this off to make some more space from the component and then put it back later i'm about to align this device here and it fits right in yeah this fits yeah this is good so here look i can look here mine is now like here aligned here and it's like fits right into the black track here this one yeah um i had to take this off actually to like make some space you know you can just like here there just take it off and just just pull it out yeah and just set it aside so now i'm going to install this little device yeah the other way around this Yeah, exactly. And just screw back in the screw so it's tight. And I'll do the same here. Just leave it out. screwing the two screws to tighten up my new component then let's see if this can still can still fit in the place before now it's too short so i would just leave it like that okay so yours worked yeah okay mine too and the things we remove just set them aside and then we can um put them back in later. So, yeah, we successfully installed the new components. And then we can just put this thing back on, this plate. And then close up the PC. Screwing this in. just like you have to do it from above you click it in here even more and then just lay it down oh wait so in your case there's not enough space for the new component so we need to make some space for that so we I think we need to remove this here it should work like that and then I think yeah I'm gonna just take this off here and this I think this can stay maybe it will fit now So this can be put back in later and just screw this in. And what I can do is just close up my PC. Slide the plate back on again. Screwing the small screws for the plate. It's tight. Hmm, try again. Hmm, looks aligned though. Okay. Okay, so now everything is tight. And then we can put the PCs back on our trolley again. Watch out, the trolley's right behind you. I will lift up the trolley. Okay, and then you can just put it on. I'll lift my PC on here too. Place it like this. And the pieces that we removed, I will leave mine on the left side and yours on the right side. We can also place our tools here. and we can also maybe we can clean up the workspace again so just like put all the things where they belong this is on the cable put it here put this back here this part is also on this table and we can push this here too um yeah and then we can And then we successfully finished the task." + }, + { + "category": "inspection_repair", + "name": "User_2_User_17_411_1410_1_480.mp4", + "transcript": " Okay, so we're about to work on a wooden block and prepare it for our operation. But first, I'm going to turn on the lights for better visibility. And the first thing we can do is prepare our workstation. yeah because it looks like yeah it seems like the table is very unstable and what we want to do is fixate it with double-sided tape like this and also use this clamp here to to mount it to mount the plate to the table below okay so first let's carry this plate down and flip it um or just lean it against table and we can put some double-sided tape here i can use this cutter knife to cut it maybe here how long should it be yeah you can uh yeah exactly okay So that's again. Now prepare another one that is about the same length. So we won't need this cutter knife anymore and the tape can remain here. I can just place the tape on top and remove the cover. And this one's a bit hard to find. yeah so now we can put the table on top and you can throw the trash in the trash bin over there yeah let's lift this up and just place it on the table but but it doesn't have to be in the middle just leave it like that yeah no that's okay yeah just for now so it's stable and to secure it even more we can take the clamp and well maybe let's use the slightly bigger one here i will open this up by rotating this screw here and If it's possible, maybe you can... No, we don't need this other... Yeah, just one at first. Just lift this up a bit. On this side too. On that side also. And then try to align this very close to the edge. Okay, so the clamp works. yeah okay just leave it like that press it a bit now we have some more space to put the clamp here okay secure it a bit more and now the table should be should be stable and secure and now we successfully prepared a workstation you can leave it like that the next thing we can do is we can take out those smaller clamps for you um place them here you will be working on this side i will be working on this side and that are the blocks we are working with the very first thing we are doing with those blocks is removing the screws and detaching this bracket because we want to attach it to the very edge of the side so for me it will be here for you it will be on this side okay but first open up your clamp yeah just pull it out maybe like um angle this this a bit so it's easier to remove like here you can angle it like slightly so it's light easier this kind of structure doesn't really align It's basically the same. Put it back up again like this. Hold it like this. And then angle up and pull it down. Okay, wait, let me try. We can try with this one. Yeah. find your angle yeah see like there's like a little there are little gaps here and if you angle it this side a bit upwards it will move very easily okay so just take your clamp and clamp your block to your table maybe on yeah on the edge yeah and then use the screw to tighten your block to the table as long as the block doesn't move anymore it's safe okay so now we will be needing our drilling machines this is yours and at first we have to assemble it therefore we can use those small toolboxes here because we will need a drill bit first and before that we can also put in the batteries and those are charging on this table so just remove the battery by pressing this button and pull it backwards then what you can do is slide the yellow part into here and the click suggests that it's secured then you can try and we can check the battery life mine is full just press the button and it's also full okay so what we can do now we open the toolbox and take out this um holder uh no just take out the holder yeah because we will put in the bits in here but first we need to open this up and therefore you press the backwards button and then you hold on to the black part of the drill machine and open it up a bit by pressing the drill button yeah while holding this yeah okay so now you see it's widely open then you insert your holder bit this side over this side oh no the um the dark um smaller side put it in and then you press the forward button and hold on to the black part and then slowly let it close until it's tight just more until it's tight Yeah, perfect. Now it's tight. Then, because you see, our screws are like a cross, have like cross slits. We will need the cross, cross heads. and you can try on those screws here if it will work and for you you can see how probably this one could work and just put it in and just open this up and slide the bit in here and then when it clicks it will be secure all right So now we can remove our screws first. Just put it on top. Secure it with both hands. And then also make sure that you are using the backwards button. This is backward. This is forward to tighten it. and then you can remove the screws yep exactly okay so now um because what we want to do is we want to attach this piece to the very side um and now what would be important is to mark everything first with our pencil so i will align this with my edge here and just draw a line here and then i'm also marking where i want the holes to be here and here and you can do the same thing with the pencil Yeah. That doesn't have to be perfect. And then also. So it's random or we put it at a certain place. Yeah. No, it's basically. Yeah. Exactly. Wait. Maybe you put them a bit too close to the ends. It's okay if they are a bit more inside. Yeah. yeah okay um now that i'm thinking of it um probably have to do it again but we have to prepare the surface of our uh wooden side with sandpaper first to make it a bit smooth and even and probably the our markings will be gone then so we can just do it again afterwards but just like just roughly yeah I think that is enough as long as the surface is kind of smooth and also the markings are not gone so that's good and now what we can also do is rasping the edges this is a rasp and what we need is to rasp and smoothen this edge where we are going to attach our device so you just take it maybe with both hands if you want and just smoothen out this edge Yeah, that's enough. And now you can continue with here, this, and this a bit. Yeah, that's enough. yeah this is perfect that's enough you can just leave it here um yeah so we marked the line here and what i want to do is i also like um saw it a bit this um border and for that we have some sauce in here yeah this one and this one um i don't know like it could be that some of them are a bit dull but we can try here some more here's one more and there's also one more but you just just follow the line align the saw with it and then start sewing like a bit slowly at first because there's no line but when you have a line then you can go a bit faster how deep should we go? you can just orientate yourself with this line here this one is a bit much but just like that Hmm, okay. then i'm using the sandpaper afterwards also to get rid of some of the wood chips here now you can see here just like just deep as this now you have the kind of like two lines here because you already started here right yeah let me try using this saw it looks like this one is a bit dull just use this line just continue with this Okay, that's okay. I can blow on it, so I can see better. Okay. No, that's sufficient. Yeah, but as long as there's a marking, it's okay. Yeah, just leave the saw there. And yeah, smooth now again. yeah so yeah the next thing we can do is yeah we are taking those markers like metal markers and just like put them on the marked holes we have and then oh yeah we will also need some hammers and they are here to just mark the drilling holes like this like that so we can place the screw here without it going anywhere else yeah that's already okay it's probably a bit big but you just need like a small yeah that's perfect now you just put your device here the bracket and align it with the holes you just um punched yeah then you take the two screws and place one of them in their hole and then screw it just slightly oh yeah of course we will need to press the tightening button but um don't screw both of them like all the way at first yeah just a bit so that you can move the bracket still you yeah you can also use it a bit like more like the button but as long as it's yeah it's fixed second one and then if both are like inside you can tighten both of them and then try to like apply force from above so it doesn't fall out i can i can also press a bit okay wait wait wait what we can do is also like put more force into it like that you have to watch out for for this because okay okay wait it looks like this could be too small yeah let's switch out the drill bit um or because i'm finished you can use mine i think this works a bit better you have to yeah it works but you have to like really like lean on top put your weight on top you can hold this yeah okay okay and now do the last one And if it's fixed, then you're finished. Okay. so now we successfully detached and attached our bracket to the other side and that was our goal so now we can start removing the clamp again just unscrew it down counterclockwise remove the clamp and then you can grab it here exactly just put it back together place them here um yeah we can the boom blocks can replace like here and take your rasp your hammer your saw um and the sandpaper and we can put everything back The hammers were here in this drawer and the rasps were here. The pencil was on the table next to the chargers. Then we have to disassemble our drilling machines again. So you press the button for pulling out. Hold on to this. Only the black part. Only the black part. Tight. And then press it slowly. Now you can pull this out. And then remove the battery. Press the button and slide it. we will have to charge our batteries again and if there's a sound it means it's charging okay so they can charge now the drilling machines yeah just slide this off take the drill bit out and take your drilling machine and place it here just place the drivet in there the holders just put them in the place you can close the toolbox and this was here and also that the clamps can this clamp was on this trolley and this clamp was here and this saw was also here then we can remove our clamp here open this up and then you can put it on the trolley last thing is we can clean up a bit our workstation just swipe off some some wood chips from the table so probably a bit from here just a bit and when you're finished you can throw it here in the trash bin you can put it here, here's more space then take your block and then we can place it in the cabinet again here and then when you finish close the cabinet door now let's lift the table and remove the double-sided tape again No problem. Remove the tape. You can give it to me, I will throw it in the trash. And then let's lift the plate on top again. And push it to the... Okay. This was on the table at first, I think. And it's a bit in the way, so we can place it. Yeah, just leave it there. And now we are finished with the task. I will turn off the light. And then we can stop." + }, + { + "category": "inspection_repair", + "name": "User_14_407_0110_1_480.mp4", + "transcript": " So today I'm going to disassemble a projector in order to inspect it. So this is my projector and I'm going to put it here on the table. So first I need to turn on the lights. So now I'm going to disassemble this projector and I need a screwdriver. So I'm looking for one here. Yeah, this is my screwdriver and this is the cable. So as I said, I'm going to inspect it by disassembling it. so it also has these two adjustable legs here when you press these buttons on the corners you can cut them out by pressing here so you can also remove this cover like this so now I am going to remove this cover Take it off. So now I'm also going to unscrew these screws in order to get this thing out. So this is a small bulb or a torch in it. Now I'm going to put it back like this. Now I'm tightening the screws. I'm also going to put this back. Like this. so there is a handle here you can press this button like this So now I'm going to remove this whole part. I need to remove three screws. In order to remove this cover, this bigger, I also need to unscrew this screw on the side and also this one. so i was doing it wrong so i think i need to take this cover off like this you can see so you can also separate these guys like this So everything seems perfect to me. Now I am going to reassemble it. First I am going to install this cover. Like this. Now I'm going to tighten this cover with these bigger screws. So I am holding it like this in order to align the holes. So now I'm going to check it if it works or not. But first I need to find a socket in order to plug it in. So I'm looking for a socket. They're disconnected here. Okay. So I guess it's not working." + }, + { + "category": "inspection_repair", + "name": "User_14_407_2910_1_480.mp4", + "transcript": " So today I'm going to correct this assembly and it is assembled incorrectly, I guess, and I'm going to repair it. so i'll be using these allen keys and this screwdriver and there are some screws in this box so first i need to fix this bar this leg it's a bit wobbly and it should be here at the corner i guess so first i'm going to unscrew it with an alum key Maybe the smaller one. So maybe first I need to loosen it and then I can move it easily to the corners. I want to fix it here. So now I'm tightening these screws. Now I need one more screw in order to attach this triangle. So first I am removing this triangle in order to align the holes here. So it's a bit wobbly, I can tighten it later. First I need to tighten the screws. So now I'm going to correct this layer. So first I need to make sure if the walls are aligned or not. This one is a bit wobbly I need to fix it Bye. What's wrong with it? Now it looks aligned but... Maybe I'm using the wrong screw. Let's try this one. So this thing is also not installed correctly and I'm repairing it. like this So first I need to tighten this triangle. so the holes are aligned now now i can screw it So I also need to install this triangle here like this. So I need to put four screws in order to fix it. So I'm trying to align these holes in order to attach this triangle. So I guess the holes are not aligned. That's why the screws are not going in. I cannot align the holes because I want to attach this triangle here but So I also wanted to fix this one. The holes were not aligned. Like these things. And I already fixed this one. So you need to also attach two square things. Yeah like two basically two slots for positioning from here this side. Here these. you also need so that you can then put them in here and also sort of they already align and you need to also take care of this one You can take a look and see if you can fit it now. And just tighten this a bit. I think it's fairly stable. And then you can also this end. You're in the wrong direction. But it should be... Okay. I guess it's not a line. That's why it's not going here. I'm not sure it was. Like the. Maybe it was too short. I think we also have some. Bigger ones. Longer ones. Longer ones. Longer ones. Thank you. It's stuck. I don't know what the problem is. But this is fitting fine. It's the same size, I think. Yeah. Yeah, this one. After a while we need to tighten it like this. And fit the caps here. This one is also fixed. A bit wobbly. It's wobbly because this is missing this year. Yeah, I tried to screw it, but it wasn't aligned, so... You can try again. Um... This is not properly in. So I think we need to first align this a few. We can try another. Is not... Okay, it is already aligned so you just need to tighten it. Can you hold it here? Yeah. I think in this case... maybe it is better to use the shorter bolts see if it's aligned i think so so then maybe you can try this Should we also put this square thing? The washer might help but I don't know if it is a problem with the size. Letting the shot screw is too short. Just try with the longer one and the washer. Try to tighten this. Take this out here so that you can control this a bit better. And tighten this. And on this side also. This one is already tightened. Is also loose. So there are only two of these capsules. So this, I think first of all, if you look at the reference image, this part is attached wrongly, so we need to move this to this side. We can start by getting this loose, perhaps, and then You don't need to completely detach it, but just make it a bit more loose. Yeah. I think now we can remove it just a little bit. And then we can just put it here. And look at the reference image. You can see here. And you can tighten this first of all. I was going to fix it, but first I wanted to finish this part. I think you can use this to detach this, perhaps. Attach this down below. You have to push this here. It should be there. This cap can fit here. There's one more remaining cap. I don't think we need it at the moment. But this, I think, will fit here. And the last thing with this, yeah. So I think we can start by aligning the slots. I think it should also be like this. Yeah. Like this. And this side. It should be here? Which one? The longer ones? These? This? I think the mistake we made was that we did not align it before, but we can quickly do it now. I think it looks similar to the reference images and it's also quite strange. This one is a bit wobble here. put the cap on And this one is also. Oh, yeah. So for this, you can tighten this here. Maybe the problem is here. I think it's more stable now. OK." + }, + { + "category": "inspection_repair", + "name": "User_14_410_2509_1_480.mp4", + "transcript": " So I want to disassemble a Mac PC and it's located in another room and I'm going to get it with this trolley. First I have to turn off the lights. So I'm going outside to bring my Mac PC It's here So I'm putting this PC on this trolley I'm putting it. So as I said, I'm going to disassemble this Mac PC. So first I'm going to remove these handles. So I'm going to un-school these two over here. For this, I'm going to need an Allen key. So now I'm removing this screw over here. So I successfully removed this handle. I'm going to put it here. Now I am removing this handle. this one is also removed I'm going to put it here so now I want to remove maybe this side so there are four screws over here I'm going to first I'm going to remove this cover Finally. So I think I have to put it down in order to remove this screw easily. Now I guess I can remove it easily. So first I'm going to detach this battery. So I'm taking it out. So... I guess I should also remove this thing. So there are two schools of here. I also remove two these. so this thing is also removed so now I am going to remove this part so there is only one screw here and now i'm going to remove this part so there is also one screw over here Now I'm taking it out like this. So now I want to remove this part. I think it's called hard drive. So I guess there are four screws I need to remove. One is over here. Maybe I should start from here? Yeah, I think I cannot remove this one over here. This one is also removed. Okay. Maybe now I can remove it easily. Still there is a screw I need to remove. I cannot find it. Oh, I found it here. So I also did it, removed it successfully. I removed it successfully. I don't know how to take it out. I think it's stuck somewhere. Okay. Finally. I did it. Now I'm going to remove this color, I guess. So there are four screws here and I'm going to remove all of them. I'm going to need an Allen key. So now I'm going to take this cover off. This is also removed. See? I guess I cannot take it off, so I leave it here. So everything is removed successfully. Now I'm going to assemble it. So first I'm going to start with installing this DVD. Yeah, I don't know how to call it. And yeah, this is called maybe hard drive or something else, but I'm not sure. So I'm going to fix it here. And then I'm going to tighten it. so i guess i'm going to need these screws so i'm going to put this thing back So I need to tighten it here. And this one should be here. so finally i also installed this thing correctly i guess so now i'm going to put this thing back here So I guess first I need to tighten up this thing. Okay. So I'm looking for a school. And I cannot find it. so now i'm going to fix this thing so i have So I also installed it correctly, I guess. Yeah, now I'm going to install this thing. But I don't know how to do it. so there are two holes over here and It should be here, but I don't know how to fix it. I guess I need some help, so I'm going to call my colleague. So now I'm going to call my colleague because I need some help. I need some help. So, I want to put it back, but I don't know how to do it. Okay. So, you have the screws? Yeah. So, just place it here and then align it with the two holes. This one? So, yeah, there are many holes here. That's why I got confused. That's where you can see it. Where you can see, like... Two holes over here? Okay, thanks for coming. So in order to tighten it, I think I need to hold it from here. so this one is also installed finally so now i'm going to install this thing and it should be here i guess So you have to align these things in here in order to fix it like this. Now I'm going to tighten it, but this is cool. so this one is also installed successfully as you can see so now i'm going to put this battery back in here like this so now I'm going to close this cover like this And now I need to tighten it with these screws. So I also need to fix this cover. So now I'm going to install these two handles. Like this. And I'm going to tighten it. This is cool. I guess I didn't install it correctly because I'm seeing a space here. so this one is also done so now i'm going to install this handle This one here. so yes i guess i'm done now now i'm going to bring it back to another room so i'm putting it on this trolley It should be here." + }, + { + "category": "inspection_repair", + "name": "User_14_411_2510_2_480.mp4", + "transcript": " So today I want to inspect this PC. First I need to check if it works or not. So I'm going to connect the power cable. And I'm also connecting this. Turn it on. See, it doesn't start. So I'm going to repair it. So I'll be using these tools. This is a screwdriver and the smaller one. So first I'm going to take off this cover. I'm putting it here. So first I need to make sure everything is connected to the motherboard. So the cable coming from here is not connected and I'm going to connect it. It should be connected here. So I have connected this one. So let's check what else is disconnected. So this one is coming from the power connection and it's not connected. It should be somewhere here or no. Maybe this one should be connected to the motherboard. So I'm going to connect it. Connect it here. So there are many, I don't know which one to connect. So first I want to connect these, the pink ones. So the one is already connected and I'm going to connect the rest. I guess these should be connected to the motherboard but I'm not sure. So the one is already connected. So the white one, this one should be placed here. So finally this is connected now. So the one is already connected here and I'm trying to connect this one here. But it's not going inside. Ah, fine. This one should be connected somewhere here, but I don't know. I'm not sure. Okay. Okay. Mm-hmm. So first I need to install a RAM. so everything seems to be connected except this pink one and I cannot connect this here. It should be somewhere here but I am not sure where. So I'm going to ask my colleague. Thank you. So everything else is connected except this one. I'm trying to connect it. Hi. I need your help. Yeah. I tried to connect this one, but I don't know where. So you already connected it here and here. So I think this is the one that's remaining. Okay. So it should be connected here. I was like. Yeah. And I think you also need a power cable for this. So. I was trying to connect the pink one here, so I wasted a lot of time. Where? The pink one here. Yeah, but it already has the pink one here. They both have it, right? Yeah. So I have already installed this one. And I was also trying to connect these. Which ones? Like these. I think these are extra, so I don't think we need to connect these anywhere. So this one is connected properly, right? Yeah, the power. And the white one here. Yeah, the CPU fan is also connected. The fan is working. Yeah. There's no keyboard, but there's no issues with the setup. Shut it down. And then we can sort this aside. It doesn't clash. I think maybe we can. I'm closing the PC and Now I'm squalling it. Those should be aligned." + }, + { + "category": "inspection_repair", + "name": "User_14_412_0710_1_480.mp4", + "transcript": " So today I'm going to disassemble a PC. First, I need to turn on the lights. Now I'm going to get my PC. It's located in another room. In order to get it, I'm using this trolley. So my PC is located in this room. This is my PC, I'm going to put it on the table. So now I'm going to unload it like this. Now I'm putting the PC on the table here. So now I'm going to disassemble this PC with these screws. First, I need to remove these two handles over here. In order to remove the handle, I need to unscrew these screws. So now I can easily remove the handle. So this handle is removed. Now I'm going to remove this handle. So this one is also removed and I'm gonna put it here. So this plate is already removed. I'm also going to put it here. now i need to remove this plate over here we cannot remove it but we can open it like this so there is a fan inside okay So maybe this cover, this plate can also be removed by removing by removing these screws over here. There are four screws in total. I wanted to remove these screws over here, but I did something wrong. I removed these screws, but I'm going to put them back. So in order to remove this part, I'm also going to remove these screws over here. I guess the upper part cannot be removed. So I'm just checking what else can be removed. So I guess I need some help. So I'm going to ask my colleague. I don't think so. I can remove anything else in order to disassemble it. So now I'm going to reassemble it. First, I'm going to install this fan. So first I need to put this thing inside in order to align these holes. Like this. I'll press it like this. And tighten it. Now I'm going to install this handle. So the holes should be aligned. So I'm not able to align the holes properly. So maybe I need to hold this handle like this here and I can screw these screws. Hi, I need your help. So I just removed these parts, like two handles and I also removed this fan and then I installed it again. But I cannot install it. I cannot align the holes. So I know it's like this. And on the other side? Nope. Okay, first I need to install this plate. Yeah. I forgot to install it. Yeah. Okay. My bad. Yeah. So now I'm going to install this plate. Now I need to tighten it with these smaller screws. There are 10 screws in total. So now I can easily install the handles. Still, I'm not able to align the holes. Can you help me? Did I do something wrong? I guess I can fix it with these handles. Yeah. So there were no schools on it, yeah. Nope. On each side there should be three holes. So which three holes there? So it should be this and this and this, I think. Yeah. Yeah. These two and. Yeah. So. So one, two, three. Oh no, I'm sorry. It's here. So one, two, three. And up here, one, two, three. Okay? Yeah. So always like one hole from the upper part and the two holes from the lower thing. And here, like the lower things, they have screws, the round screws. Those two, for example. And the one up here is the school right there. So first I'm going to fix these schools over here. So these screws should be on the top here and here. So now I'm going to tighten them. So this one is done. Now I'm going to install this handle. So first I'm going to tighten the upper one." + }, + { + "category": "inspection_repair", + "name": "User_14_412_0910_1_480.mp4", + "transcript": " So today I want to inspect my PC and it's located in another room and I'm going to get it with this trolley. So first I need to turn on the lights. So now I'm going to get my PC. So this is my PC and I'm going to load it on the trolley. So now I'm unloading it and putting it on the table. So first I need to check if it works or not. For that I need a power cable and I'm going to get it. so now i'm going to plug it in see it's not working the led light and So as I said, my PC is not working and I'm going to inspect it. And now I'm going to disassemble it. So I'll be using this screwdriver to unscrew all the screws on it. First, I want to remove these handles. So this handle is removed, as you can see. Now I'm going to take off this handle. And now I can easily remove this cover and I'm going to put it here. So now I'm going to inspect the fan inside it. So there is nothing wrong with it I guess. So I'm going to put it back. So there's nothing wrong with the fan. So now I need to check the DVD. See, it's not working. So the LED is also not working. So now I'm going to remove this cover. I'm taking it off like this. So first I want to remove this device here in order to inspect it. So the LEDs were working. I guess the problem is not here. So I'm going to reinstall it. So now I'm going to take off this guy. so still the led is not working and the dvd is also not working so i guess there is nothing wrong with this guy either and i'm going to reinstall it so as you can see everything is connected there is nothing wrong with these cables oh i see there is one cable that is disconnected see the white one coming from the led so maybe here this can work And I'm going to fix it. so this cable was disconnected that's why it wasn't working the led and dvd so now i'm going to check it if it works or not let's see yeah now it's working you can also open the dvd yeah okay perfect So as you can see, everything is working now. Now I'm going to reassemble everything. First I need to put on this color. Now I'm tightening this girl with these screws. So now I want to install this blade. I'm going to place it here. Now I need to reinstall the handles So now I'm putting back all the screws. So I need to align all the holes in order to fix it. So I'm not able to align the holes. Still I'm trying. so i'm not able to find another hole i mean the upper one I need to align the holes in order to fix it, but I cannot. So I'm going to call my colleague. Hi, I need your help. What's the problem? So I cannot align the holes. So I was reinstalling the handles, but... Yeah. It looks right to... Ah, okay. It has to be up here. The two holes. Just take this off again. Can you take the handle? Let's go. Yeah, and for the handle to be fixed, this hole needs to be aligned with this one. So we want it like this. Okay. I can just screw it in and I hold the handle. It has to be the flat one. yeah okay thanks yeah no problem So this one is done. Now I'm going to install the other one. So first I need to align all the holes like this. So now I'm going to put back all the screws. So first I need to fix up our board. So this one is also installed. So now I'm going to check it again if it's working or not. Okay, yeah. I guess everything is working now, as you can see. Turn it off. So now I want to bring it back and loading it here. And the trolley. So now I'm unloading it and putting it on the floor." + }, + { + "category": "inspection_repair", + "name": "User_14_412_2510_1_480.mp4", + "transcript": " So today I'm going to inspect a PC and this is the PC I want to inspect. So first I'm going to test it if it works or not. So I'm connecting these cables to this PC. So I'm connecting a power connection. So it doesn't start. I guess there is something wrong with it. So I'm going to repair it. so i forgot to turn on the button let's check it again it doesn't start so now i'm going to repair it and i need some tools and these are the tools i'm going to use So first I need to test this front lock to see if everything works properly. This looks fine. I think there's nothing wrong with it. So now I'm going to take this cover off. I need to unscrew it. Now you can take it off easily. So first I need to check what's wrong with it. So this yellow cable is disconnected and I'm going to reconnect it. So as you can see, these cables are not connected to the motherboard and I'm going to reconnect them to the motherboard. These red ones should be connected here, but I'm not sure. I guess two should be connected to the motherboard, but which one I'm not sure. These three I guess should be connected here. like this. So now I'm going to connect the other cables. I don't think so I need to connect to this one. I guess that the similar one is already connected. So I'm also going to replace the RAM. and i'm going to insert a new one So this one is also seems to be disconnected and I need to reconnect it. Should be here. Yeah, it should be here. Hi. I have a question. Should I connect this one, or I don't need to connect it? So you need to install the hard disk. Small? Yeah. Here, so you can take the... Disconnect this. Disconnect this, and this thing will come off, and then you can put the hard disk. connect this to this okay and and this cable this cable is the data cable so it goes here everything this is damaged so so i have already connected these here so you can connect but first just mount it because the screws you can mount it from here like you need to take this plate off basically and then screw this in like this here but where are the holes here? okay so this one should be connected over it's like here but why should i take this off because you cannot take the plate off without that there are screws on this side and this side once you take this off you can remove the tray and then take this off so i'm taking this plate off in order to install the hard disk These are the two screws. How many do we need? Four, but... I think these are well suited for this I'm going to try with the small ones I'm going to use the smaller screws here I can't think the size fits. we need smaller screws for this and we don't have I think you can also repair this without the hard disk. So put this back with the screws and you can connect the rest of the things like whatever is remaining and then you can try and start the system. So I'm trying to connect the blade, but the holes are not aligned. Yeah, okay. Now the holes are aligned, I guess. So I'm using the cross-headed screws. I should be using the smaller ones. So I have put the plate back, now I'm going to install it. First I'm going to place it here and I need to align the holes. I need to screw it." + }, + { + "category": "inspection_repair", + "name": "User_14_414_2609_1_480.mp4", + "transcript": " so today i'm going to disassemble a table and it's located in another room i'm going there so this is the table i'm going to disassemble So there is a plate inside it. I'm going to remove it. First, I'm going to remove these screws over here. And I'm using this allen key to remove them. I'm going to put it here. So there are also three other screws over here. I'm also going to remove these. so i have removed this blade you can see i'm going to put it here and now i want to remove these bigger screws with this allen key In order to open this cover, I'm also going to remove these screws over here. So I have removed all the screws. So this is a handle or a lever. You can adjust the table with this. And I'm also going to remove it, but I don't know how. now i can take it off easily i guess so i have disassembled this table completely see And now I'm going to assemble it again. So first I'm going to install this top right here. So now I'm going to install this layer. So now I'm going to put these screws back. In order to put it correctly, properly, I'm going to hold it here, press it down. So the hole is not aligning. So this side is done. Now I'm going to work on this side. so now i'm going to tighten this top with these smaller screws there are six in total sorry i forgot to install this plate it was under this table first i'm going to install this So I have to align this hole here in order to fix it. Hi, can you help me installing this plate? Yeah, maybe. Yeah, this should be inside. Okay. yeah can you hold it here so i so this is not aligning here okay maybe a bit still not oh i have to use so open key wait So for this, I'm going to need this one, the smaller Allen key. This one? Should I loosen it, or? Yeah, let's get out the whole different thing. No, it's not. which one? okay okay thanks for your help yeah i can do the rest okay you sure yeah Can you hold it here, like this? Ah, okay, I see, I see. Yeah. Okay. Thanks. so these holes should be aligned but i'm not able to do it yeah yeah like this So finally, I have assembled it properly. You can see. So everything seems perfect. Yep." + }, + { + "category": "inspection_repair", + "name": "User_14_451_1202_Repair_480_User_16.mp4", + "transcript": " so now i'm going to fix this pc first put gloves on one hand and the other hand so we can see this is the pc and this part is uneven so it seems like something inside is not set it properly but i will plug in first to check so this wire is plugged in here so I will plug in here it seems a problem CD drive is a problem it's a warning so I'm gonna plug out Let's open this up, see what's happened with this PC. I push this button and lift. Open it. So this PC looks like this. you can see the light is shining somewhere which means some part is incorrectly first I'm gonna check if the chip rack is correctly so it seems not because this bolt is outside and it's not aligned with the plug out first and put it aside gently and then take out the dust to see what's happened inside so this wire is not connected so the data to the CD drive and the power of the CD drive also not connected so we connect it in connect them in so this is the power supply it's all attached here it's attached one two three four so it seems the hard drive is not in so we put the hard drive in put it in the next hard drive, hard task put it in, plug in connect the power cable and data cable also this one, the power cable and the data cable plug in check, check, check so the wire is connected so the GPU, the power so we can see the battery is not connected we have to remove the gpu to get the cmos battery remove the bolt remove the bolt using screwdriver remove the bolt using screwdriver remove a bolt using screwdriver remove the bolt using the screwdriver so now all the bolts are out so we are going to remove the cable of the gpus first this and disconnect them the flip So this disconnected the chip and now the bolts are all removed. Now we remove the GPU. And we can see the CMOS battery is dropped. We are going to put the battery back on. So the battery is on. You can see there are four REM are missing. I'm going to attach the REMs. Second REM. Third REM. So the REMs are attached. This is not what I want. We can see the fan is not connected. So we are going to attach the fine. This cable needs to be attached. We are going to also attach this cable. Be careful of the wire. of this CPU are loose and it's tightened the cooler is tightened tightened the bolts tighten them all tight tight we can see this wire is also loose this fan power fan power cable to be connected connected the cable is on next cable is connected check this cable check this cable check this cable the CD drive all cables are connected now so now we are going to put the gpu back it's going to go this way attach them attach them also here need to be attached and put the bolts back on pick up screwdriver pick up a bolt fastening the bolt pick up a bolt using screwdriver fastening a bolt pick up a bolt using screwdriver fastening a bolt pick up a bolt using screwdriver fastening a bolt pick up a bolt using screwdriver fastening a bolt grab a bolt use a screwdriver to fasten a bolt repeat fastening bolt grab a bolt screwdriver to fasten a bolt fasten the screwdriver and fasten the screwdriver So these are tightened. These are tightened. The REMs are on. Now we put this duct on. Like this. I'll put this back. Slide in. And now put the cable back connected to the GPU. This connected to here. This connected to here. Now we test connect to the power cable connected to our computer The fan is working well. CD drive. I need to turn it on. CD drive. Oh, it worked. So this is good. Now plug out. Check one more time if everything is connected. USB is not. CMOS back on. Ships back on. Attached properly. GPU back on. It's all good. Fan working well. So it's successfully connected. Oh, sorry." + }, + { + "category": "inspection_repair", + "name": "User_14_451_1302_1_480.mp4", + "transcript": " Come pictures from the camera. Take the camera and the tripod. Close the door. Go to room 411. Enter the room. Close the door, turn on the light. What am I doing? First, set up the camera, the tripod. Loose, make it easier. I'm going to do is find the horizontal level Okay, the bubble is just in the middle. I can fix. Three ways to rotate. Let's adjust the height. Take out the camera from the camera bag. Take out the camera. Be careful. And first, I'm going to remove, replace the lens. Be careful with this. Replace with this one. out the cover on the old one with the CMOS And then put the battery and SD card back on. Here's the SD card. This way. When I hear the click, this is good, go. And the battery, this way. So push it, lock it. And then, if we want to put the camera onto this tripod, we need to replace this into plate. using some tools I might need. Put it on. This goes this way. make it tight this big arm okay horizontal level in the middle Fix it clockwise. And what I want is to take a picture of the robot arm. Same horizontal, same horizontal, and the lower. try to put the arm in the middle of the screen take picture of the arm let's see how to zoom in a little bit Let's take one more picture with the automatic mode. good and turn it back and turn off the machine back the cover and push this to remove from the tripod the same thing remove this plate Put this thing back. Remove the battery and SD card. If I click the blue button, click the SD card, it will automatically push off. Put this thing back to the back. And take out the lens. I click this button and rotate here. Put the cover back on. Put the original. hearing the click means it's going back on put the camera back to the back put the lens back to the back protect Back to the normal. Loose the screw to make the tripod. Fix it a little bit. Take this tripod and the camera back. Turn off the light. Open the door. Close the door. Knock first. Open the door. Close the door. Put the camera back on the table. Put the tripod back. And open the door. Close the door. I went back to 4.11, opened the door, closed the door, and finished." + }, + { + "category": "inspection_repair", + "name": "User_14_2325_451_2_480.mp4", + "transcript": " So I'm going to repair this PC. First I need to check if it works or not. I'm kind of connecting the power. See it's not working. I need to repair it. And I'll be using these tools to repair it. I'm gonna take the cover off. Let's inspect it, what's wrong with it? so everything seems to be disconnected the fan is not connected to the motherboard properly i need to fix it and the hard disk is also missing so first i'm gonna screw the fan in using this screwdriver screw it in like this the holes should be aligned Thank you. I'm tightening this closed. Yeah, now it seems good. And this cable should be connected to the motherboard right here. And the battery is also misplaced. I'm gonna put it back here. I'm installing the hard disk. It should be placed like this. The heart should also be connected to the motherboard. So I'm gonna connect this cable here. And what else is missing? The rim. And there are some other cables are also missing. I need to install and connect them. So I'm connecting it to the motherboard. This one is also connected. And there is one left. That should be connected to the motherboard. so everything seems to be good now i have connected all the missing power cables and other things it should work now but i also need to tighten this thing So yeah, everything seems to be good. So now I'm gonna close it. So now I want to test it if it works. I'm connecting the power. I'm also connecting the monitor and the keyboard. Yeah, the monitor is also working, so everything is working." + }, + { + "category": "inspection_repair", + "name": "User_14_2325_451_480.mp4", + "transcript": " So I'm gonna repair this PC. First I need to check if it works or not. So I'm kind of connecting the bar. It doesn't work. I'm gonna repair it. First I need to take off the cover. Let's see what's wrong with it. So I'll be using these tools. First I need to inspect it. What's wrong with it? Everything seems to be disconnected. So the fan is also missing. I need to install the fan. I'm gonna place it here and then screw it in. The holes should be aligned. So now I'm gonna screw it in using this screwdriver. Mm-hmm. Okay. Thank you. so i have installed the fan i guess i installed it incorrectly i need to unscrew it again So it should be placed like this. So then I can connect this cable here. I'm screwing it in again. It seems good now. This one is also disconnected, so I'm going to connect it to the motherboard. and the battery is also misplaced so there is nothing wrong with the RAMs they are already there let me check this button to secure it Thank you." + }, + { + "category": "inspection_repair", + "name": "User_14_User_2_412_1110_1_480.mp4", + "transcript": " and put in those two drives, devices. So it loads, yes. And then placing the PC on the table here. And then you can just do it at the same time and I will show you how to do it. So we also need some screwdrivers. We don't need it. So I lost one, yeah. No. Did you? Okay. Thanks. So now I'm going to take off this cover and I'm going to put it here. So which screwdriver should I use? The green one? You can use whatever. Yeah, this one. so i'm also going to remove this part right it's the same for you so you need to remove this one first so now i'm going to remove these screws over here there are eight you don't need to remove those screws okay then this one I also removed it successfully and I'll put it here. So this yellow part should be down. for you too but it also looks like you have to remove something these things you can remove this one here so now i'm going to remove the green part here yeah and you can Should I also remove this part? Like the other one? I think it's enough if you have just like this free. So this fits in there now. So now I'm going to install this device into this PC. So I'm placing it inside. Like this. So the yellow part should be. So how can I align these things? The yellow part here. How should I put it inside? Like this way? No, it also doesn't fit. like you see the structure of this can fit here because there's this thing so this for this to fit in there the constellation needs to be the other way around so and this is also not possible so how i understand there's no way to place this part in there okay so for example this one looks like the black track here looks like it fits because the small black hook goes here this one goes here and this one goes here yeah then i then i need to remove this spoiler yeah so these two or yeah this one and this one okay And you can also put those back. Okay." + }, + { + "category": "inspection_repair", + "name": "User_14_User_15_411_1010_1_480.mp4", + "transcript": " So last time I reassembled this lamp incorrectly. Now Yasmina, my colleague, is going to show me how to fix it. Okay, so first we can see where the problems are. We put this into here. You can't move it down. So the workspace for here, you can't move this part down. So this is wrong. Also, it usually should go this way over. this bottom part so that it moves correctly. So I'm going to take this out again. And we're probably first going to drag this part down here. So in order to do that, we're just going to unscrew this screw. Second, I have to take off my rings. Maybe you can already unscrew. Like this? Yeah. So I'm just going to put this over here. And then take one. Maybe I can write it here. Maybe I can remove it. And this one. Thank you. again making sure it's in the groove and then attaching it to this one here and now if we put it back in here on the clamp yeah this is already correct Unscrew these. And this. And this part. Okay, so. I'm just going to take this off. is that this round part goes on here. As you can see, there's the markings from where it's moved around. this came from, I think here? No. It should be here, like? In here? Yeah, maybe. No, no, it was. Where was it? I don't remember. Oh, no, I do. It should be in here. Okay, now we can put the top back on. No, the other way around, because it has these groovings for that to sit. Okay, yeah. And then I'm going to take these screws, put them in the holes, and then screw this part back on by rotating the screwdriver clockwise. The same over here. So again, just rotating the screwdriver clockwise. And now all that's missing is that part. So it was like this? Yes. Okay. it will move around. And if I loosen it, I can move it to like here or here, whatever I want. No, it's not working. And now you can move this around again so that if I want to put light on something over here, I can just move it around like this. I can also, if I loosen this part a bit, if I loosen it, I can position it however I want and tighten it again by rotating clockwise. And now the whole round is fixed again." + }, + { + "category": "inspection_repair", + "name": "User_15_410_0511_1_480.mp4", + "transcript": " Okay, so I have been given this PC, which as you can see up here has been marked effective. Down here we can see what is actually the problem. So what we have here is a missing battery and a RAM chip. We also have some detached cables. So let's just open this up by pulling this latch out. to take a look inside so now I can open this up like so okay so right away I can see that these are probably the detached cables so I'm just gonna make sure they line up yeah like this and then I can connect this And then also this cable, as you can see, is missing. So I can just go ahead and connect that. Now what else was missing? I'm just going to have a quick look. A RAM chip and the battery. So I'm going to look in here, see what I can find. There's the battery. So we're going to connect that. There we go. And now we just need a RAM chip. Which I believe is... is this so i'm just gonna make sure that these holes line up and then just stick it in you know that it's fastened when these click like this okay now i think i'm just gonna put these tools back now i think um everything should be fixed so i'm just gonna close this back up again i'm gonna pull this out to secure it And now we can test if it works. So for that, we need a power cable, which I have right here. So I'm going to connect that right over here. And then we need, we need an outlet. There's one over there. So maybe let's put this here. Maybe if we carry this over there, we can see. I'll just plug this in like so. Oh, we can actually, I think, leave it on the table. See if it boots up. Okay, nice. And then we can check if the display works by connecting this cable. Right over here. And let's have a look. The PC is running. I don't see anything on here. Oh, I think now I turned the display off. There we go. It should be connected. Let's see again if we turn this off. We have to press longer to turn it off, I think. Okay, so the PC is running again. However, the display is not quite working. So I'm just going to turn this off again, which also doesn't seem to be working, and then just unplug it and take this out. I can put this back here and now the PC is technically still defective but we can take these off because it is not missing the battery, the RAM chip anymore and also it doesn't have detached cables. And that's the repair." + }, + { + "category": "inspection_repair", + "name": "User_15_410_0810_1_480.mp4", + "transcript": " Okay, so today I want to disassemble and inspect this PC, but I can't do that here because I don't have any tools here. So I'm going to take this over to a different room, which is room 410, which is at the end of the hall. So I'm just going to go and bring this PC over there. I'm just going to close the door and turn on the light so that I can see a bit better. And then I'm going to take this over to that workstation or table. Okay. And then I'm going to grab some tools, which I'll probably need this and these, but we'll see as we go. Okay, so first I'm going to take, oh, there's another Allen key. So first I'm going to try to take this top part off. So you can just open this latch like this by just turning this around. Usually you would also have a key if you wanted to lock it, but We don't need that. So I can just open this and also open this and have a look inside here. So I can also unscrew these. Actually, I can do this by hand because they have these knobs around them that make it easier for me to turn them around. And I'm just going to loosen this part as well. Nope. It's not coming loose for some reason. Oh, this is for, also the fan is in here and on the inside there's the casing for the fan and I think these are for that. So I'm just gonna close this right back up and then try to get these handles off by just loosening all of these screws. So I'm gonna use this screwdriver, which you can change the bits. And then just by turning counterclockwise, I can take these screws off. I'm gonna put them all in a pile so I know which ones go where. There we go. Also the last one of these rounded ones by rotating counterclockwise and now I have these at the top. I'm also going to rotate the screwdriver counterclockwise to get these out. Same over here. Whoops, and it's already slipping. So I'm just going to hold onto it while I take this off. Like this. And then I'm going to see if I can find a screwdriver for this maybe. But I don't think I see any that would fit this so I'm just going to leave the handles as they are and I'm going to take the left one off as well. I'm just going to put these all in here so that I know which handle they belong to and then I can take off the handle on this side by again rotating counterclockwise to take out these rounded screws. The same on this one. and these ones as well. So at the end I'm usually just doing the last bit by hand just so that the screw doesn't fall to the ground. Then I can also take these top ones off. There we go and this one. Oops. I'm going to hold onto the handle again so that it doesn't fall when I take the last screw out. There we go. Just going to collect all of these and put them over here as well. Okay, now we have the handles off and we can also take this casing with the latches off carefully. And let's see it has filters in here and the fan. And now here I don't think we can do very much. So what I'm going to do instead is take this upper casing off. So for that, I'm just gonna turn this PC over like so. I'm also going to take this chair because I want to be a bit more comfortable. Okay, and now I can take these screws. They also have these knobs which I can grip easily so that I can turn them out myself. like so. And then I can just take this plating, slide it out and lift it up and I can reveal the inside of the computer. And here we just have a plan of how it is built. So just some major components, what the indicators mean or what they are. Yes. And so I'm just going to put that to the side so that I can look at the inside of this. So in here we have these things, which I'm not sure what they're used for, but basically you can unscrew this a bit and that lets you move this arm up and down so that you can probably connect it down here with something. But in order to see the rest a bit better, I'm just going to take this part off. So I'm just going to unscrew this. by going counterclockwise. And I'm gonna put this over here, put that there, and then I can, I should be able to just lift it out, but it is somehow connected over here. Let me turn this around so that I can see. I think it's just, yeah, like this. So I can just take this off. I can look at this. It has these things which you can move up or down by loosening this and moving it up or down. I'm going to put this to the side over here with the screw so that I know where that goes. And now we can look inside. So we have a fan here, we have a fan there and another fan here. This might be a bit hard to take out, actually, but maybe we'll try taking these plates out. They're for the different adapter kinds, I think. So I'm just going to loosen these screws right here by going counterclockwise, and then I can just take them out. The same with this one. Here as well. And this one. And finally. I'm also going to take out this one, which I think is actually for the casing and not the plates, but we'll take a look at that. Okay, so first this one. Oh, okay, so this is just for the ventilation, I think. So I'm going to put them all here in the correct order so I remember. This one, I'm... I could remove now, but I'm not actually going to because it's stuck in there and I don't want to mess that up. This one, however, I can remove to show you. It's connected via this cable over here. I'm going to slide that right back. right back in there we go this one I'm I could also remove but I won't because it's stuck in there and I don't want to although I'm going to leave that in here just in case I mess anything up this is actually missing a piece so I don't know where that went but I'm guessing it's probably another one like this or in case you wanted to add another one of these types of things for the I don't know what this is. But this part I could also remove, see how it's wiggling. But I won't because I don't wanna mess anything up. So now I'm just gonna put all these parts back just because I don't wanna get confused with anything. So I'm gonna put this part back and then all the screws as well. So this part should actually be a little bit magnetic just to make it a bit easier. Put these screws back in. So I'm just going to rotate the screwdriver clockwise. There we go. Now that is back in. Now the next screw, I'm just going to take these in. These are all connected separately via one screw. So now this one, rotating clockwise again to tighten it. This one as well. Like this, rotating clockwise. I have three screws left over here. And they go here. Now this is actually missing that part, so... It technically wouldn't need a screw because there's nothing for it to hold in place, but I'm just going to put it back in case somebody wants to add something later and needs the screw. And now the final screw is going to go right over here to secure the last input like that. And then I'll see what else we could look at. So we have these cables, which this one, I think we can remove, or maybe not. But I think I'm just gonna take this off maybe. So for that, I'm just going to unscrew these and for this because it has a hexagon shape I'm going to need an allen key so I have a couple right here I'm just going to see which size is the best so this one is actually a bit too small I think the next size up is this black one yes that fits so I'm going to rotate this counterclockwise I'm actually going to use the other side to make it a bit faster so there we go this side as well just unscrewing this. Um, and then I'm also going to unscrew this top part for this. I'm going to use this wrench or this screwdriver again, just going counterclockwise, the same over here. And then all these screws, I'm just going to put them right over here so I know where they belong or that they belong together. And then I think I can take this part off. Put that over there as well. And I thought I could lift this. Oh, I can slide it out and then we could lift it up, I think. Yeah. Maybe if I slide it out a bit more, there we go. Um, so this is actually where the DVD goes. It's not powered on, so I can't show you, but this would slide out technically and you could put a DVD in there and there would technically I think be something in here, but currently there is not. Um, so yeah and then these screws are just to keep these components in place which i can actually i could show you i think or maybe not because i think they might be oh no i can okay so i'm just gonna try to balance this here and then use this screwdriver to take out these screws and I'm going to put them in another small pile here and then just again the last couple rotations I sometimes like to do by hand so I'm just going to remember that they were in the top spots and I'm just going to turn this over and unscrew these screws by again going counterclockwise A little bit more. Now that fell down. I need to pick that up in a second. I'll take this one out first. So again, going counter. counterclockwise. That was the wrong direction before. I'm just going to take this final screw out, which is a bit tricky because these are all connected. I can just take the screw that fell down, put it over here Um, and then take this screw out, also put it over here so I remember that they belong together. And then I should be able to, well, I can't see properly. Take this part out. If I just slide that up, maybe or not, I think it may be, it might, it seems like it's stuck on something. Oh, because this plastic casing is too big for me to pull it out. So I think I could take that off. I press on here, which is kind of hard to do. It's not really working. Okay. So technically I would be able to take this out if I could take the plastic casing off, but that's not really working right now. So I'm just gonna slide this right back in and put these screws back so I'm just going to slide this so that the holes align and then I remember that they were in the first couple holes so I'm going to put them right back there For that, I am, I think, going to turn this around like this just to make it a bit easier for me. I'm just going to take the screw, rotate counterclockwise to screw it back in, and do the same here. Remember, these are the screws for this part. Maybe I can lift this up a bit so that the holes align a bit. the screw fell down okay now I can screw this back in by rotating clockwise and now all that's missing is the other side so I'm just going to turn I'm going to balance this on here probably. And then let me see, I'm just going to turn this around and do it like this. Oops. I think that's fine. Um, so I'm just going to take the screw again, find the hole, rotate clockwise. to screw this back in place. Oh, maybe I need to lift this up a bit so that the holes align a bit better. Yeah, there we go. Rotate clockwise to screw it back in and then do the same for this one. I'm just gonna take the screw. Oops. This is a bit tricky because I haven't unplugged this. Maybe if I hold it like this, it's a bit easier. Okay, I'm just gonna put this to the side real quick and then try to use my fingers to screw it in for the first part maybe. Fall down again. That's no problem. Oh my God. Just need that to stay there. up there we go okay now i can screw that back in that was a bit hard but that's because the screw is so small and everything so i'm just gonna screw that back in okay and now i'm gonna put this whole contraption back to where i got it i could Oh wait, I could take this bottom part off. So I'm gonna do that again. These are the same screws as we're on top of here. So I'm just gonna use the same Allen key to loosen these. Again, the other side is a bit faster. So I'll put these all on a pile here. This is just a metal plate for it to slide in, I'm pretty sure. So that's a bit more secure. Yeah, now that all the screws are unscrewed, I can take that off as well. Nothing special. These are just the screw holes. So I can just put this back and screw them all back in by rotating the allen key clockwise like so. And I can fasten this. Do the same for all the other sides. First, I'm gonna use my hand to kind of get it to grip. And then I'm gonna use the Allen key rotating it clockwise to put the screws back. This one as well. And the final screw. we go and now I'm just gonna put this whole contraption back the way it was so I'm just gonna slide that in here just gonna slide it in there which it should be Should be working, but it's not completely. There we go. Okay, and now I can screw it back on. So I'm just gonna place this on top of here again. And then these were the screws that I placed with that. So these tiny screws, they go in these holes. So I'm gonna fasten those first using the screwdriver by rotating clockwise. The same with this one. Rotate clockwise again, and then I'm going to fasten this fastening to this contraption. Um, but for that, these are the black screws again, which have the hexagon shape. So for that, I need an Allen key, which I have right here. Same one again, cause the size obviously didn't change. And then I can just screw that back in this one as well by rotating clockwise. we go and now everything is back connected i'm just making sure that all these wires are secure okay and then let's see uh before i loosened the screws on here so i think i might be able to take this off as well or the casing for the fan if i just unscrew these screws, so these four. So I'm going to try that. I'm just going to take these out by taking the screwdriver, rotating counterclockwise. One, two, three. And the final one. Number four. I'm going to put them all in a pile. And now the only thing that's keeping this connected, I think, is this part at the top. So I'm going to unscrew that as well. Rotating counterclockwise. Now these are all the same screws, I believe. So it doesn't matter which ones go where. Okay, there we go. And now I should technically... be able to take these be able to take this off because it's not screwed in anywhere anymore I don't think maybe at the bottom let me look at that nope it's not screwed in on this I think it's just stuck somewhere probably Let me see. Let me open this part up. Oh yeah. It's these screws that it's stuck on, which I don't know how to take off completely. Um, but you're probably not supposed to take these out that much anyway. Um, so I think these are, these are what's causing the issue. Maybe if I unscrew these things inside. No, that's not possible. So I think this is just holding this filter to this and I can't take that off. But at the same time, it's blocking me from taking the whole thing out. So unfortunately I can't do that. So I am just going to put the screws right back in. So I'm going to start with this top ones. I'm just going to put this back. and just screw that in going clockwise same for this one again just oops rotating clockwise and then these i know there's a few holes but i know which ones these are supposed to go in because i can see behind the um this plate there is another um place for me to I mean there's the this part so that I can see that that's where the screw goes so right here again just rotating clockwise also over here and here rotating clockwise again and here as well like that okay let's see what else could we take off well i could take this plating off but i think oh actually i'm going to take this off by just unscrewing this part first these top screws again this is just the same thing as with the fan over there so just unscrewing these small screws um by rotating the screwdriver counterclockwise and then I'm going to unscrew these black screws which are the same as here with this allen key by rotating counterclockwise again this is maybe not the best order of doing it but that doesn't matter And I can just take this off and also lift this part up, which holds, what is this? This is, I'm not sure what this is. And I'm also not sure what this is. Let me see if I can read anything. 160 gigabyte. but not much else. Yeah, but back here you can see the LED lights that technically if we were connected to electricity, which thankfully it's not, otherwise I would probably electric it myself, which would make these light bulbs light up to show you the status of things, I think. Um, yeah, but there's not much else here to show. This is just to keep the cables organized. So I'm just going to put this back and see these, these little, I don't know what to call them. These, um, Well, anyway, these go into these holes to make sure that this is in the correct place. And I'm just gonna put this back on. I'm going to start with these ones, the small ones up here. Like so, again, just rotating clockwise to screw these small screws in here with the screwdriver. And then again, I have to take the Allen key to screw this part back in. Again, rotating clockwise. Same over here. So I'm just rotating this long bit to make it a bit faster, and then I'm using the shorter bit up here to get a bit more leverage to actually, oops, to tighten these. Okay, is there anything else? Well, there's these cables that are not connected, though. I don't think I can unscrew this. Well, I could, I think, technically, but this bit is not long enough, so I'd need a different screwdriver for that. Yeah, but I think that is basically it for inside here. So I'm going to put this part back. I'm just going to take this screw out right here and then fit this back in here. So this goes in here. It's like a little like a puzzle kind of. And then I can line this up again. Take the screw and screw this back in here. So now that everything is back inside, actually, I think maybe I could take this casing off maybe. Let me try that. So in order to do that, although maybe not, because now I've just screwed all these parts Although, wait. No, I can take this off. So I'm just going to unscrew this apart. This part as well. And then, oh, something is stuck in there. So I don't know if I can actually take this screw out, actually. Which is a bummer. What is in there? Yeah, I can't get the screw. I don't have anything sharp really to take this yellow gunk out, which is a shame because otherwise I could have taken this metal casing off by just unscrewing these screws. And then this one and this one, but that is not possible. So I'm just going to put these screws back. They went right here. So just rotating clockwise, the same with this one over here. And I think that's all we can do here. So now I can put the backing back on, which slid down a bit so these little things they actually slide into here so I'm first going to put this down like so and then it should slide down and then I just slide it a bit further to close it back up And then I'll screw this back in with these screws, which I can just do by hand because they have these knobs on the end. The same over here. I don't know if it's not fully in yet, so I'm going to take this actually out again. Not fully. I don't think so. There we go. Okay. And now I can just take these and screw these right back in here and here as well. And it's all lined up. Okay, and now I'm just going to stand this PC back up. Well, that's not really supposed to happen. But it's not screwed in anywhere. I didn't loosen any screws here, I'm pretty sure. I'm going to look at that later, I think. Maybe actually, maybe we'll just do that now again. I'm going to put this down again, take this backing off again. Just going to put that on the chair. And then I could try and have a look why. This doesn't fit anymore because there weren't any screws that I loosened that I know of. Maybe you just have to push it in. I don't know. OK, so I'm going to loosen this again just so I can take a closer look. at this and I'm actually just going to loosen these top screws so that I can move the whole compartment. I don't actually have to remove this part in order to look at this. I think maybe I just didn't put it in correctly. So I'm just going to screw this back and then see if it's still moving around. I'm just going to do one so that I can check. Nope, that's still moving around. Okay. So that did not fix the problem. Just gonna unscrew this again. And then I can take a look in here. Cause usually I feel like you would screw the sides in, but I didn't unscrew those. They weren't screwed in in the first place. So I'm not sure. What's gone wrong here? Why? Yeah, see here, you would screw this in this part. They weren't screwed in in the first place. So I think that's why they're moving around. Because anywhere else, I don't think I can screw. Yeah, there is nowhere else for me to screw. So I think it's just cause there's some screws missing to connect this part properly, which is a shame, but that's the way it is. Um, so I'm just going to leave this and then maybe I'll find some screws later that I can screw in there to to fasten that a bit more securely. But for now, I'm just going to screw this back in. Maybe also tighten these ones again with this Allen key like this. and like that okay and then now I'll put the backing back on so again these small things go back here so I'm just going to place this here and then slide that all the way back so that I can then put these screws back in here and in here now i can stand the whole pc up okay now it's holding i don't know why um i can screw this back oops there we go um and now i'm going to put this part back as well so it goes right on top of here And it's, I think, just being held on by these handles. So I'm just gonna put these back on as well. Just fit them on here. The holes should line up, but they are not for whatever reason. One second. Oh, the handles, they go, nope. Do they go on? Oh, they go in between. So this actually goes on top of... No. Okay. This may be not... Rectangle for this side, maybe this is for this side. These also don't line up. Okay, one second. So this should go on top of here. I'm just a bit confused as to how the handles attach. Because The holes don't line up. Maybe it is done, but that doesn't make sense. How? How was this? That hair? Hmm. Cause this is a little bit too high. So that the holes... They don't actually line up with where the handles are supposed to go. Cause this is supposed to... Oh, maybe. Cause this is... Hmm. Hair. Hmm. I'm a bit confused now. Because this also doesn't line up. Am I being stupid? Let me look at this side. Is there a difference between these? No. Because this hole is supposed to line up and this hole is supposed to line up. However, it isn't lining up. I don't understand. Am I just missing something? This also isn't lined up, so it has to go up here, but I don't know. I don't know how." + }, + { + "category": "inspection_repair", + "name": "User_15_411_2410_3_480.mp4", + "transcript": " Okay. So today I have this PC that apparently does not work. So I want to inspect and repair that. So first I'm going to see what doesn't work. So in order to do that, I've already plugged it in. This has been turned on and now let's turn this on and see if anything. Well, we can also open this latch by just unscrewing these screws going counterclockwise. And then I can take this off and I will place it right over here. And as we can see, not a lot is happening. So I'm just going to disconnect that from the power again. also take out the power plug so I don't electrocute myself accidentally. And then we can see what could be wrong with it. So the first thing that I see, which I can also see in this reference picture right here, is that this power cable is not connected. So I'm going to do that by just Now taking it and sticking it in here, making sure it clicks to know that it's inside. The next thing I see is that it's missing a RAM chip, which usually has two. So I am going to take one from this box of replacement parts. So right here, this one, and I'm going to slide it into here first i'm going to open these clasps on either side and then carefully see how the middle has a notch here and there's a notch there i'm going to carefully slide it into place and push it down however this is not connecting right now So maybe I'm going to take this off so that I can move a bit more freely by just unscrewing it going counterclockwise. So I can take this off and put it to the side. Now I can see that this is actually blocking it from going back. So what I have to do is I have to just unscrew this. So this is actually the graphics card that's in the way. I'm gonna put the screw over here and now I can take this out, push this back like so, so that this is properly connected. And now I can put this graphics card back in place by carefully pushing it down and then screwing it in place using this tiny, tiny screw, which I'm gonna place right here. and then i can screw it in by rotating the screwdriver clockwise there we go okay now that that is fixed um i also noticed that it's missing a hard disk up here so in order to add that which i have over here i have an extra one i'm gonna unscrew this so first i'm gonna oh i need an allen key for that actually so i'm gonna go get one of those And they should be in one of these drawers. They are. I think maybe this size will be good. So I'm going to try that. Yeah. And by just going counterclockwise, I can take these screws out. I'm going to put them just up here so that I remember where they go. Like so. And then I also need to unscrew this top bit to be able to pull this out, I think. I don't think it's connected anywhere else. So again, just using the screwdriver, going counterclockwise. I'm gonna take these tiny screws out. like so and i can take this plate off and i'm actually gonna put all this over here so that nothing accidentally falls inside the pc and now i can take this off i'm just gonna move this up a little bit so that i can now let's see to screw this on top of here so in order to do that i'm going to need to take this plate off so again i'm just going to unscrew it by screwing counterclockwise and then keep the screws over oops the screws over here do the same on the other side like so and like so now i should be able to just slide this out now i can put this hard disk on there flip it around and now we need some screws to fasten it and i think i have some in here yes here they are some tiny tiny screws there's one two three i think we need four probably um let's see okay so i only have four of that type but that is uh three of this type which is fine i think it'll still hold um so i'm just going to line these up and then screw the hard disk Let me see if this is. Yeah, I'm going to line them up like this instead so that it's right there and then put this screw in here. Tighten that. And now do the same over here. I'm going to start with this corner because if you do it diagonally, then you know the other two holes will be lined up correctly too. just screwing clockwise and then i'm also going to put one here like so and i am just going to double check real quickly that i'm not missing sewing a screw but I don't think I am okay so now I can slide this part back in here and we can fasten this again using the screws we took out before so what do we have to do we just have to line up these holes and then we can take these again tiny tiny screws and screw it into place by rotating clockwise And we'll do the same over here and on the other side as well. Make sure that everything is nice and secure. There we go. And now we can put this back in here carefully. You see these holes down here and they go in the spikes down there. I'm just going to carefully check that there's no spare cables like this one, for example, take that out. Nothing that I need to remove down here. And then I can put this piece back and also screw it back on using this part. So first I'm going to take these tiny screws again and then just screw this bracket on top of here by rotating clockwise again. And I'll do the same right here. And now I'm going to use the Allen key to put in these screws. to fasten the bracket to the actual thing. And just again, turning kind of clockwise. There we go. Okay, now that is secure. I also notice, if you open this, that this is actually missing a DVD or CD slot. So, In order to put that in, we're going to have to take this big box out. So same procedure as here. I'm just going to take this off. Just unscrewing all these screws. I'm going to store them all in a pile over there. And then I can take this off and I should be able to slide this part right out. And now I can mount this in here. And I know that it goes this way around because this is going to be the top. So I'm just going to try to slide this from the other side. I'm going to try to slide this in. And then line all these holes up. There we go. And now I'll take these screws that are left in here, which should be six, I think. Here we go. Yeah. Um... These are all different types too. I think these ones go on here probably. So I'm going to use these ones. So I'm going to just take this one, place it in here, screw that tightly, and I'll do the same here. I think two screws on either side will probably suffice. I'll do the same over here. And here. There we go. These two can, for now, go back in here. And now I can put this thing back, just need to move this cable out of the way, then slide it all the way down and back in place. And now I can actually put it back in place by placing this plate on top again, screwing that plate into the casing of the PC by rotating clockwise. And then using the Allen key, I'm just going to fasten this right here and right here. Here we go. Now what we have to do is we have to attach. What's the difference here? uh the data and the power cable so i am going to just do that which i think let me just look in here again to be sure but no that's fine so i'm just going to attach that right here And now these, I'm not entirely sure, but this is power cable too. So I think this one goes here and this one should go down here. There we go. I also noticed that this fan is not plugged in, so I'm just going to Plug that in here, as I scroll to the side, so that I can pull this forward and see what else isn't connected. What I do notice is there's a battery missing there. If you look at this reference picture, it has a battery. And thankfully I do have one left over here. So I'm going to place that in there. We don't have anything for this to connect to. But other than that, maybe I will actually bind these wires together because they are kind of in a way. So I'm just going to take a loose zip tie. And then take all these cables. Make sure that this part is facing outward. And then push the end of the zip tie through here. tighten that and then using a box cutter right here i'm just going to slide this out carefully i can just cut the end off off of the box tie a zip tie i mean sorry there we go i'm gonna put this back in put this back in the box this as well we don't need that um yeah but i think we've put everything back so we can put this part back as well so i'm just gonna hook hook that in here and then screw that down with this screw And so far I can't see any other issues with this. With this PC, some of those cables, there's nothing else. I think that's fine. Yeah. So let's check if any of that made a difference. So I'm going to just plug this back in carefully and then turn it on. And there we go. This fan's working. I can hear this going, but we can actually look inside and see if we can open this. And yes, we can. So I'm just going to close that again. All the lights are lighting up. Everything's connected. The fans are going. Both of them over there too. So I think I think we fixed it. So I'm just going to turn this off again and then put the big cover back on. I'm just going to pick that up. Place that on here. Whoops. Carefully. And then slide that in and screw it back in as well. There we go. So this I'm going to put back in my box. This I can put in the trash and these I can go back in the cupboard. So this I got from here. This screwdriver goes here and now the PC is fixed and ready to be used again." + }, + { + "category": "inspection_repair", + "name": "User_15_412_0110_1_480.mp4", + "transcript": " Okay, so first I'm going to turn on the light so that I can see better. And then I want to disassemble this projector. So I'm going to carry it over to my workstation. And then in order to disassemble it, I'm going to need a screwdriver, which I'm going to go get from a different room. So that is just over here in this room. And it's usually in one of these drawers. I think I might need this size. I'll also look for a different one just in case. Okay, so I will take these two over to start disassembling the projector. okay so i think this one will probably work a little bit better so i'm going to start with this one and first i'm going to take this covering off by unscrewing this screw right here by turning the screwdriver counterclockwise and now it should come right out i just use my fingers to pry this lid off. There we go. And that is where the battery usually sits. And so I don't lose a screw. There's also this little backing that keeps it in place even when it's not screwed in. So this is where the battery is. It's also screwed in. So I'm going to unscrew this as well. Well, it's a bit difficult to get out, but I think we've almost got it. Actually, I'm not sure. I think these might have the same backing as this, so I'm just going to screw those back in. But this is where the battery goes. Now this is where the filter is and I, by just pushing this part in, I can open it up. Take this part off. Also take the filter off very carefully, making sure not to damage it. And then I'm going to unscrew these, these three screws to take this off. Also you can move all both of these up and down and these in order to level your projector and I'm going to unscrew these screws but also going counterclockwise and I can take this off it's a really long screw Then I'll do the same here, rotating the screwdriver counterclockwise. I don't know. Did you look in the second? No, like one like this. And now I can take this screw out and the final one is here. And again, I've just screwed it counterclockwise, and then I'm using my nail to get the screw out. And now this part should theoretically lift up, but I think we might also have to loosen this screw, so I'm going to do that really quickly. Also rotating counterclockwise. There we go. Let's see if we can take this off. You can also try turning these, but I don't think these come off. Let's try this. Maybe if we press these two sides, it'll come off. I'm going to screw these all the way up and then press this little button on both sides to kind of try to move this part off. which doesn't seem to be working because we do need to loosen these two screws. Oh, that's the wrong one. We need this one again going counterclockwise. And I'm collecting them here so that I know which ones belong where. And the final screw on this side going counterclockwise. Okay. And... Now let's try again by pushing these two buttons on the side, see if we can move this part. I don't know where else it is screwed in actually. So I'm not sure that we can take this off. Open the handle to just look inside. And I don't see anything. So I don't think you can take this off like this. You can take these things. These things out. I'm going to screw them back in actually. Um, so that's just for that, but that doesn't help us in taking this big part off. Um, and I don't want to break anything. So I'm just going to leave it as is check if there's anything else that we can disassemble. But I don't think so. And also these two holes, they are meant to be, or these three holes are meant to be able to screw the projector onto something so that it stays. So for example, like up top, up there. But since I can't take this covering off, I'm just gonna put everything back. So I'm going to start with these long screws, which went in these holes. So I'm just gonna stick that in. And then by rotating the screwdriver clockwise, I'm just going to screw that back in until it's tight. And then I'm also going to do that for here. And for here, this one. And now I have these three screws left, which remember go here. So I'm going to screw that back in by rotating the screwdriver clockwise until it's tight and I can't rotate it anymore. And then these also go on the side. And again, I'm rotating clockwise and pulling it tight. Whoops. And also on the left side, just sticking it in the hole. And then rotating the screwdriver clockwise until it's in there. Okay, and now I can put the coverings back on. So I'm going to start with this one. I have to put this part first because it has these little ledges that need to go in first in order for it to fit. Then I can fit it on there and screw it back into place. by rotating the screwdriver clockwise. Now I can put this filter back in and see how it matches the shape. And now I can put the guitar the grate back in which also has these ledges so you know these go in here first and then they can plop down until it snaps into place usually. Maybe this isn't completely exactly where it's supposed to be, but there we go. Now it's snapped into place and now I have reassembled the entire projector. So I'm going to actually show you how it works. And for that, I need the cable, which is, where is it? Um, I can't actually find it right now, but I'll still show you how it works in theory. So of course you can use these feet to move it up or down by rotating in the back as well so that it's level and you can see how it works. And then you need to open this or take this cap off. And with these things you can regulate it. or make it sharp once you see the picture. You can imagine that. And then these buttons are to turn it on, to reset it, to adjust the volume, to get to the menu, to get help and to navigate the menu. And yeah, that's how that works. I'm going to just put the cap back on. And I'm going to also put these two screwdrivers back into the other room where I got them. And I got them from the second drawer, so I'm going to put them back in there. And now I can also turn off the light here." + }, + { + "category": "inspection_repair", + "name": "User_15_412_0110_2_480.mp4", + "transcript": " Okay, so first I'm going to turn on the light so that I can see better. And then what I want to do is to disassemble this projector. So I'm going to take this over to my workstation as well as this screwdriver. And then I can start disassembling. So for that, I'm going to turn this whole thing around. And then what I can do is I can take this sort of gate thing off by just pushing this plastic bit in and then I can open it and the filter comes out with it. I can also take this off. So I'm going to do that by just unscrewing the screw by rotating the screwdriver counterclockwise. And then I can take this panel off and in there what we have is the light, I think. So I'm going to loosen these screws by again going counterclockwise. And I'll do the same here. And as you'll notice on this panel, the screw has a little backing on it, which prevents it from falling out or falling into the actual projector. And the same thing is true for these two screws. So that's why I can't unscrew them completely. As you'll see, I'll just be screwing them out for forever. So I can actually pull this out. And you can see this is the light here. and these screws have the same backing. So I'm going to put this off to the side and then I can unscrew this small screw to get the casing off. And I'm going to put that over here. I'm also going to unscrew this small screw. and put that over here as well and it has another one on the other side like so and then I'm also going to unscrew these long screws by again rotating the screwdriver counterclockwise And then I can just take them out using my nail and I can put them over here. And the same is here. So I can unscrew this by rotating the screwdriver counterclockwise. And now the last time this projector was disassembled and reassembled, this screw would not fit back in here. So we're also going to look into why that is. And then these feet, I actually cannot take off as I'll show you, but they are there to level the projector so that the image that you project is level. And you also have these up here, which you can take out or make bigger by pressing this button. and pulling it out or pushing it back in the same as on this side and pull it out yeah but now i'm just going to turn this over and see if we can remove this top casing now which we can with just a little bit of wiggling so we can remove this And then we can also, it seems that this was disconnected. So that needs to be put back at some point. And then we can also remove this top or this front casing just by unscrewing this screw over here. And what's nice about this screwdriver is it has a bit of magnetism built in, so the screw should stick to it, but it doesn't. So I'm going to use my finger to get it out so that I can disconnect this. And usually these would be connected, but they were disconnected the last time, these little wires. So I'm actually going to reconnect them. like so and this one as well in a second just so you can see this is the fan for the ventilation system this is the hole where the lens or the projector looks through then and then i'm also going to connect these two cables like this and then where did i put the screw over here i can put this covering back on here. So for that, because I have these little feet on here, I have to lift this part of the projector up a bit so that I can fit this back on. And this part is actually broken, so I don't need to unscrew that. But I am going to put this screw back over here in this small hole is where it goes. There we go. And by rotating clockwise, I can screw this back in. And as I said, this part's a bit broken. Okay. So something that we can unscrew here, maybe the handle. So if we push on here, the handle comes loose and we can also just unscrew that with these two screws to take it off. So again, going, going, Counterclockwise, I can take these two screws out. There we go. Maybe a little bit more. And this one as well. and now you should be able to take the handle out but i think it might just be wedged in a little bit because it has those things that are holding it fast so you can't completely take it out but that is how you would by then unscrewing this part so that you can lift it up and that you can get the handle free but for now i'm just going to put these screws back by rotating the screwdriver clockwise which takes a little bit. And now I'll do the same for the other side, rotating the screwdriver clockwise to screw these screws back in. and I can also push the handle back in and I can also unscrew this part so again by going counterclockwise I can remove this screw and then this little piece should come off and I can just put that right back and put this screw back as well by rotating clockwise. Okay. Now this part, I'm not actually sure about how this goes back on here. Um, cause it was already off. But I think it goes in here probably. But again, I'm not sure. I'm just going to put this, try to stick that in there. Okay, and now we can put the casing back on. and turn this around again to put all the screws back into place. So first I'm going to start with the long ones which go in here and by rotating the screwdriver clockwise I can just screw this back in once it connects. until it's fastened. There we go. I'll do the same over here. And these are just to connect this top casing while the small screws are there to connect the front casing to the main part of the projector. And that's tight. And I will also try to reconnect this screw. But it still will not go in. So I'm going to leave that. And put these little screws back for the outer casing. Oops. So I actually need to hold this a little bit so that it's... Oh my god. So that it's lined up. And then just rotate the screwdriver clockwise to screw the small screw back in. And the same on the other side. Just rotate it clockwise. And on top right over here. And now I can also put this lamp back in. So I'm going to do that. Just slide it back in until it's flush so that I can put these screws back by rotating the screwdriver clockwise again. The same on this screw. And now this can't just fall out. And I'm going to fasten the bar with this plastic thing. And then I can also put this plate backing back by putting these ledges, or I don't know how you would say this, putting these in here first. And then I can screw in this screw as well, just by rotating the screwdriver clockwise. and do this and then also put this filter back on which also has these ledges which i'm going to hook into here and then this part actually moved so i'm just going to put this back by hand then put these ledges of the grate in there and snap it closed and this part and now i can turn this back over and show you how it works and for that I'm going to need the cable which should be in this cupboard over here so right here and now I'm just going to untangle the cable and then I can stick this part into here and then this part into a socket like so. And in order to see a picture, of course, we have to take the lens off or the lens covering. You can also just these feet, both here and here and here and here, as I said, to make it more level. And I'm just going to turn it on by pressing the power button. But it doesn't seem to be working. If it were working, you could then use these to make the image sharper, to regulate that. And then these buttons are, for example, for the volume, to go through the inputs, to go to the menu, to navigate those, to get help, to reset the whole thing. Yeah, maybe it's not plugged in correctly, but I think it is. The power socket should also be turned on. And it is. But this is not turning on, so I'm just going to put it all back. Put the lens covering back on. I can take this cable off and unplug it. And then I'll just put everything back over here. Put the cable back in the cupboard. And then I'm going to turn off the light because I don't need it anymore." + }, + { + "category": "inspection_repair", + "name": "User_15_412_1510_1_480.mp4", + "transcript": " Okay, so today I want to replace this graphics card in a computer. So in order to do that, I'm going to pick up the computer. First, I'm going to turn on the light. And then I'll use this trolley to pick the computer up, just because it's in another room. I'm just going to push this over. The computer is in this room. There we go. And now I can just take this computer by its handles and then place it on here. And then I can take this over back to where I want to work on it. I'm gonna move this chair a bit out of the way so that this fits. And then I'll close the door to this room and take the computer back to the room with my workstation. I'm also going to close this door and then I'm going to take the computer over here because I want to work on this table. So first I'm going to remove this monitor and put it down here along with this cable. I'm going to get rid of this water level as well and this remote I'll put over here. The water level will go over here. I'm going to move the graphics card to the side. And because I need to access the inside, I'm going to put the computer on here with this side face down. So I'm just going to pick that up, lift it, and place it onto the table like so. I'm going to move this trolley out of the way and pick up the tool that I will need, which I already know is a screwdriver with a cross head. I'm going to take this and now um i will open this up by rotating these screws which have like this grip on them so i can just use my hands um but just rotating them counterclockwise the same over here That's a bit hard, so I'm going to use the screwdriver just to help me. There we go. Put this on the side. And now I can take this casing off. I'm going to place this on the floor here. And this graphics card actually goes over here in this section. So I'm going to have to take this off. So in order to do that, I'm going to unscrew this screw by going Why is it not working? Going counterclockwise like so. I'm going to put this over here with these ones and then I can lift this up. and out. I'm going to place that over here and then we can take a look where this goes. So since this needs two of these slots, I think the easiest thing for me to do is to just remove these two and then place it here. So in order to do that, I am going to use a screwdriver rotating counterclockwise to take this part out like so. And I'm going to put the screw over here. And I'm also going to take this part out by rotating counterclockwise again. Place the screw over here. And then I can carefully take this part out, like so. Put that over here. And now we can place this graphic card in there. So I'm going to line these up, as well as this with here. And carefully place this in there making sure that everything lines up and then I can then push this in until it's secure and then I can actually secure it with the screws that I took up before so for that I'm going to take the screwdriver as well as the screw put it in the hole make sure it all lines up and then rotating clockwise I can screw the screw in like so And I'm also going to put this screw back in this hole. It's a bit hard because it's very small. There we go. and again rotating clockwise like so now this is all nice and secure I'm going to put this part back on so first I'm going to put fit this latch into here like so so that it goes back to where it went and then I'm using the screw I'm going to screw it back in place to secure it by rotating clockwise And now that this is all secure, none of this is in the way. I can now put the casing back on, which I'm going to pick up from the ground. And then just carefully slide that on. Like so. And then I can put these two screws back, which I'm just gonna use my hands for. Screw these back on. Like this. And like this. This one's always a bit harder, so I am going to use the screwdriver. Okay. Now that I have everything secured, I can put the screwdriver back to where I got it. And these parts, I'm just going to keep over here. And now the graphics card is switched. Here you can see the ports for it. Yeah, and that is how to replace, now that I've successfully replaced the graphics card." + }, + { + "category": "inspection_repair", + "name": "User_15_412_2409_1_480.mp4", + "transcript": " okay so for this recording I'm going to turn on the light first and then I'm going to take this and first loosen the brakes both on the left and the right hand side Now it's loose on the right. Not on the left yet though, I think. Okay, now we have both breaks loose and now I can open the door and go to the other room to pick up the computer that we're going to disassemble. I'm going to open this door. And then I will just pick up the computer by its handles. Put it on here and bring it back to the other room. And close the door. Okay, now I'm closing the door again and I'm going to bring the computer over here to this table. And first we're going to clean this up a bit so we have space to work. So I'm moving the chairs out of the way and tidying up the pens and pencils These are the tools that we will be using. I'm going to move this monitor as well by gripping it at the bottom. And the cables are too short, so I'm going to put it off to the side instead of on top of the table. Okay, now we have our computer. And with this thing done here, I can lift it up by stepping on it so that I don't have to strain my back. Okay. Now I will put this computer on the table. Move the screw. And then we can start the disassembly process. So first we can also take a look inside by opening it here. And we can see the inside of the computer. And now we're going to close it again. And first, we're going to take off the handles. And for this, I will be using this Allen key of a size 2.5. And then we can just screw these and we'll have to go counterclockwise to loosen them. To unscrew them. There we go. And the other side, also again, counterclockwise. I have to get the screw off of the Allen key. So now I've used a different Allen key to sort of pry it off the original one and we can just take off the handle. And I'm going to repeat this three more times, always unscrewing counterclockwise to take off all four handles. Maybe it's better to use the long side for this part. because there's not as much space to turn it all the way around. And again, starting with the short part and then I'm going to use the long part to completely get the screw out. And then I'm going to lift the PC up to get the handle out like so. And now do that again on the last corner. Here's one screw. And with the last screw, I'm using this Allen key again. Turning it counterclockwise to unscrew it first with the short side and then with the long side to make it easier because I don't have that much room. And now we can take this handle off. Like so. And also these two parts that came off or not. Okay. Now what we're going to do is we're going to take off the outer casing again with the Allen key. This time we can just use the short side because we have that much room. There we go. That's the first screw. And now we will do this one. And I'm going to store them separately from one another because the ones for the handles are a bit shorter, so I don't get confused when putting it back together. Again, I don't have enough room to move this all the way around. So at first I'm using the short side and then the long one. And the reason I'm using the short side first is because it gives me more of a more power, you could say, to unscrew the screw properly. Okay, and now we can take this outer casing off. At least we should be able to. Oh, it's screwed to this part, so I'll have to see if I can loosen that. Maybe with a smaller one. No. So here we had this. So I'm going to try and use this to take out the screw. Which is working. So now we have the small one. And again going counterclockwise with a screwdriver. Okay. And now we should be able to take this off. I think it's still connected in the middle. So unfortunately, we cannot take this casing off, but we can try on the other side. Again, going counterclockwise to take out the screws. And again, I'm using an Allen key and rotating it counterclockwise to unscrew these screws. And the final one. And now this casing should just come right off. but it is also connected in the middle with another screw, which I can't access. So unfortunately we can only, so we can only unscrew the screws, but we could look what we could unscrew in here. So if we open this up, we could unscrew these parts. Maybe. Unfortunately, these are not the right size wrench. Let's see if we can find anything else. No, this won't fit and neither will this. But we can unscrew these screws, I'm pretty sure. Just again, going counterclockwise with the screwdriver. We have one. And the second. And again, I'm using the screwdriver to screw counterclockwise in order to unscrew the screw. Okay, but now this whole thing will not come off because it is still screwed in over here and I don't have the right size wrench to unscrew that. So now we're going to put it all back starting with the screws for this and for this I'm going to put the wrench in the screw to hold it in place and then turn it clockwise to screw it back in place. And I'm doing the same with this one. Okay. And the same with this one again, going clockwise this time. Some reason this is not working. Okay, these are still loose. So I'll try unscrewing this one again because I think maybe something went wrong there. Okay, now I'm going to take these all back out. Because the fan is now misaligned, I think. Which I can't get back though. So we're just going to put the screws back in. Where's the third screws under the computer? Okay. Now we can close this back up and we can put the screws. Oh, first we're going to put these two screws back, which were the small ones. So I'm using this again, which is a bit tricky because the screw is so small. And then rotating clockwise. Okay, now we can close this back up and put back the screws that we took from here. Again, putting them back with the Allen key and going clockwise. And for this, I'm using the long side because it makes it a little bit faster to screw things back in place. Just turn it like this. And now for the other side. Again, rotating clockwise. And the last one, going clockwise again. Now the handles, we're going to start with the ones from the top, which are these. So I'm just going to fit them back on. And then I'm going to take the screw, put it in the hole, and then use the Allen key. to fasten it in place a bit, but maybe also put in the other screw already so that it fits right. Okay. And I'm going to use the Allen key again in the, rotating it in the clockwise direction to screw the screw back in. Here we go. Now on the other side, clockwise. Okay. Now the other top handle, I'm going to take it again, fit it back on the computer. Screw in the screw a little bit first on each side so that it's secured. And then I'll take the Allen key again, rotating it in a clockwise direction. So to the right to fasten the screw. Okay, now to make things a little bit easier for me, I'm actually going to turn the computer around like this in order to screw these handles back on. This one is for this side. I'll take these two screws. Put them in to secure the handle. on this other side as well and I have to hold the computer because the bottom here is rounded so it won't stand on there. OK, again, using the Allen key and rotating it right. As well on this side. And now for the final handle, I'm going to take this, fasten it on here. Again, put the screws in part way to secure it. And then the final screw. I'm going to put this in here. I'm gonna lay this down to make this a little bit easier for me as I'm trying to screw. There we go. Okay. Now let's all put back together. We can put back the tools that we used and then slowly let this thing down by using this brake here very carefully so that it doesn't slam. Now that this is down, I can put the computer back on it. And we will also put this monitor back that we put away before. And now I can use this to bring the computer back to where it came from to the other room. I'm going to open this door. And I'm going to open this door. Hello. Hi. And I'm closing the door and taking this back. Okay. Now we have this back. We can turn off the light after we close the door and finish the recording." + }, + { + "category": "inspection_repair", + "name": "User_15_412_2709_2_480.mp4", + "transcript": " Okay, so first I'm going to turn on the light so that I can see what I'm doing better. And then I want to dismount or disassemble this lamp. So I'm going to take it off of its stand. And then first I'm going to dismount the head, probably take out the light bulb first by rotating it counterclockwise. And then I can take off this lampshade by unscrewing these small screws going counterclockwise. So I have to actually hold this bolt at the end of it so that it actually screws out. Now I have the screw and the bolt taken off of the first half. Now I can do the same on the other side by again holding this bolt down here so that I can screw the screw out of it and give it something to grip onto. Okay, there we go. And now the lampshade is dismounted. I'm just going to move down the line so I can also disconnect this here. Again, there are bolts at the bottom, so I'm going to hold onto those so that I can unscrew the screw by rotating the screwdriver clockwise. Okay. Now I can unscrew this screw the same way. And take this part off and I'm going to put this over here with those screws so I know where they go. And then I'm going to take out the screws on this part so that I can separate the two. I also have to hold the back again so that I can have something to hold on to. Okay, and now these springs have loosened as well. And I can take them off. And the last screw on this part, again, the same principle. Okay, and now I'm going to move on to the bottom part, which is again, has these connected springs, which I can also just take off like this. And then the final two screws. And on this side, we actually have this knob that lets you turn the lamp or loosen it so that you can turn it. So you can just unscrew that as well. and then take out the screw and now everything is disassembled and I can now put it back together the same way that I took it apart just reversed alright so this pole it goes back here and I'm going to use the long screw which goes through this part then through the pole and out the other side and I can connect it back with this part which I can just stick on and then I stick this in here and I can screw it in by rotating the screwdriver clockwise while holding the bolt at the end. Also I can screw the bolt on with this white thing if I hold on to the screw on this side. There we go. And now I'm gonna screw this part back in. So I have to move this part around a bit so that the holes line up again. There we go. Oh, yeah. And now you just screw one of these bolts to the end of it to fasten it. Okay. Now I can put the springs back on. by putting them on this part first and then on this part. Also on the other side, put the hook on this part and then on this one. And now we need to connect this edge part with these two. so first i'm going to do the top part i'm going to push this white part back in so that the holes line up properly like that and then i'm going to take one of the screws first put it through here and then through this part if it lets me like that and now this part I'm going to again take one of these bolts or nuts I'm not sure and just screw that on by hand and then I can fasten it by using the screwdriver while holding onto the back part like this and then I'll do the same with this one so first I'm going to stick this part in here so that the holes line up. Then I can stick and push the screw through and fasten it with and fasten it with this And again, holding it at the back so that I can properly tighten it up here. Okay, and now for the final part, I'm gonna put this in here. Again, line up the holes so I can push this screw through. and then tighten it or secure it with this part and then tighten it with the screwdriver like so. And now we just have to put this part back. So for that, I'm first gonna connect it to the top, the top bar. So again, I'm just gonna push the screw through after I've aligned the holes and then tighten it back or secure it with the small part back here and then tighten it with the screwdriver. And now I can fit this lower bar into here. Also align the holes again so that I can push this screw through. And then secure it with the backing. And tighten it with the screwdriver by holding the back part. um yeah and now i can reattach the springs by first putting this loop on this one and that on this one on the other side i'm going to put this loop on here and then on here now all that's left to do is to reconnect the lampshade so what i'm going to do is i'm going to align these two holes with here. Maybe like this is a bit easier for me to do. I'm going to take these little screws and put this on my lap so that I have more stability. So take this and then I can put in one of the small screws. And now I have to take one of the backings and try to fit that on there, which is going to be a bit difficult. So maybe I'll turn this around. Like this maybe. If I hold it with my two fingers like this, I can put in the screw. Hold it with this hand and then place the backing on it and screw it back in by going clockwise. All right, now one screw is done and I can take the second one and repeat what I did before. So first I'm going to stick the screw in the hole and then hold it while I put the backing on. And then now I'll take the screwdriver again. The backing came off. And by rotating the screwdriver clockwise, I can screw that back in. like so i just have to put the light bulb back which i do by also going clockwise okay now the lamp is all done and i can put it back on its stand which is over here you can just Take this clamp off by rotating this part to the left and then you can take it off and put it back on by rotating this lower part to the right. I can stick the lamp back on here and I can plug it in and use the switch to turn it on and off. as well as use these bits to kind of loosen this part so that I can move this around. I can also lift this arm up and down as well as this part so that I can move where the light goes. It also swivels. I can also loosen this part to make it a bit easier. But that's it. Now I can turn off this big light because I don't need to see anything more clearly anymore." + }, + { + "category": "inspection_repair", + "name": "User_15_414_2509_1_480.mp4", + "transcript": " Okay, so in order to see better, I'm going to turn on the light. And then I'm going to put on these steel cap shoes. By first taking off my normal shoes. And then I'm going to slip my foot in here and tighten the shoe by turning this wheel. And I'm going to do the same on the other foot, tightening it by turning the wheel to the right. Okay, and now I'm going to put on these gloves to lift that table over there onto the wagon so that I can transport it to my workstation. I'm just going to take it and lift it up and put it on here. I'm also going to take my tools with me so that I can then disassemble it. Okay, now I'm going to bring it over to the other room to my workstation just by pushing the wagon and I'm going to open this door and then bring it over. I'm going to open the door further to fit the wagon through. And close the door again. Now I can take the table off of the wagon. and move the wagon to the side so it's not in the way. And now I'm going to disassemble it. First I'm going to take out this mechanism to move the table up and down and then I'm going to use probably this Allen key which is size 2.5 to loosen these screws. So I'm going to turn it counterclockwise to loosen the screws. And for this part, I'm going to take off the gloves to have more mobility. And I'm going to collect the screws over there so that when reassembling it, I don't lose any. Again, using the allen key to turn counterclockwise to unscrew these screws. and now on the other side also counterclockwise Now with this last one, I have to be a bit more careful because there's plating under here, which will come off. And I'm going to store this all over here, so that I know which parts belong to which. And now, using the purple allen key, which is a size 4, I can take out these big screws. Or, maybe a size 3 is better. Nope. This has four. Again, turning it counterclockwise. And if I need a bit more force, I will use the short side to unscrew the screw, at least at the beginning. And then I can use the long side once it's a bit easier. Again, I'm using the shorter side and going counterclockwise so that I can have more force to loosen the screw up before I unscrew it. Now we have all the screws from this side out. Now we can do the other side, which is again the same, just going counterclockwise. Now I'm unscrewing the second screw on this side. Again with the shorter side of the allen key first so that I have more force. And now the third screw. and the fourth one. Okay, now I'm going to gather up these screws and put them over here so I don't lose them. And then we can take off this top casing. And we can take a look at the mechanism inside, especially here. So we can fit this handle back in here, and then if we turn it clockwise, the table is moving down, or the stand for the table. And if we turn it counterclockwise, it's going to move the table up. So now to put it all back together, first I'm going to put this outer casing back on. First on one side and then on the other. Probably it's better the other way around. There we go. And now I'll take all these screws that we used in before and put them back. Using the same allen key as before, but this time turning clockwise. So that's one screw on this side. And the second one, again turning the allen key clockwise to fasten the screws. And now I have to move this part of the leg a little bit so that the holes for the screws line up. And lift it up a tiny bit. And again screw the third screw in also going clockwise with the allen key as well as with the fourth hole. Now I'm going to do the same on the other side. Again, turning the allen key clockwise to screw those screw back in. and now the second screw is screwed in and the third and with the fourth screw I have successfully screwed the whole outer casing back on And we can then move on to screwing on this part. I'm going to put all these screws over here and then try to line up this casing or to line the holes of this casing up with these holes. First I've pressed this metal plate back into its spot and now I will take this light blue, which was a size 2.5 Allen key. And screw these screws back in by going clockwise. And this will hold this smaller metal plate to the outer casing. Now for the third screw I have to move the metal plate down a little bit so that the holes line up. And I can screw the screw back in going clockwise again. Maybe I'll do the outer one first so that this lines up a bit better. And now I'll put in the last screw on this side. Maybe do the other side first. So on this side, the holes have to line up as well. We're going to start in the middle, just turning clockwise. I'll start over here. and then do this side again going clockwise with the allen key now we'll do the middle I have to hold this metal plate up a bit so that the holes line up and I can screw this back in. Okay, so this does not seem to be working, so I'll have to get somebody else to help with that. But we can put this handle back in to see that the mechanism is still working. If you turn it clockwise, the table moves downwards and counterclockwise makes it move upwards. and I'm going to clean up my tools by putting them all back in their designated place which for the purple key is the 4 dark blue is number 3 and the light blue is 2.5 I'm going to put these here with the screws so I don't lose them put my gloves back on so that I can lift up the table and put it back on the wagon so I can bring it over to the other room. I'm going to open the store. And then move this table Back to the other room. I'm going to close this door as well. Ooh. I'm going to put this table back here. And close the door and now I can unload the table. Take off my gloves. as well as the steel cap shoes by pulling out this wheel and then just opening them. The same on the other side, just pulling it out and opening them." + }, + { + "category": "inspection_repair", + "name": "User_15_414_3110_1_480.mp4", + "transcript": " Okay, so I've been given this assembly, but if you look at the reference picture, this is assembled completely wrong. So what I'm first going to do is I'm just going to take basically everything off the frame because I think nothing is really at the right place. So to do that, I'm going to use this Allen key and I'm going to just start over here by unscrewing counterclockwise. And I can just lift this whole part out. I'm also going to take this off by again unscrewing counterclockwise. And take the bottom screw out as well. I'm going to use the short side to have a bit more leverage. Like that. And now I can use the long side. I'm just going to place this over here. And now I do think... Let me look at the picture. I think this pole is correct, but it's supposed to be in the middle. So instead of taking the whole thing off, I'm just going to loosen these screws a little bit and then kind of push it into the middle. I'm just loosening these and then this one as well. And then now I can move this to where it will be in the middle and now i can just screw these screws back in by rotating clockwise and i'll do the same Now this is all secure, but this is still at the wrong place, so I'm gonna take this off by rotating counterclockwise. And I think this goes up here, just this way around. So I'm just gonna take that, slide it all the way up to where it's at the correct height, and then I can tighten it again by rotating clockwise. I'm just going to make sure that this screw is correct as well. There we go. Now that this is fixed, next I'm just going to take this bracket off by again rotating counterclockwise. There we go. And now I'm just going to put this big plate back on, which goes on like this I believe, or Yeah, like this, it doesn't really matter, but that means that I have to put these in the correct positions. And in order to do that, I need to obviously not cover the picture. Look at that. Okay. So it actually needs to be this way around because we need one hole. here so this is at the correct place already need another here so i'm just gonna move this part up a bit and then use the allen key to make sure it's in the right spot and then this one i can just move down a bit to the right here maybe make sure it's all in the correct spot and then we are missing one of these over here so i'm gonna look and see if I can find one right here to slide into there. I'm gonna do just that. Take it and slide it in to where I think the hole might be and it is at the correct place. So now I can just use some screws to screw this plate back in. See if we have some left over here. I'm going to need four in total. I'm just going to place these in here, just loosely at first, and then I'm going to tighten them. There we go. Okay, now I can tighten them by rotating the allen key clockwise. Oops. Like so. Just to make sure that it's really tight, I'm just going to use the short end, which has more leverage power to really tighten it. Okay. Now, let's look at the picture again. I think The only thing that's missing is on this side so I'm going to turn this around. We have an extra bar here because if you notice there are two of these long bars. So I think this one is actually at the correct place. This one needs to go here. So what I'm first going to do is first I'm going to take this off because this does not go here. and I'm going to take this it already has these connected here so I might as well use that to kind of screw this bracket to there very loosely so I can still move it around and I'm going to use this oh there is another one of these so this has to go here and I need a screw kind of screw this on to this bracket like so. Now that is at the correct spot. Now I just need to move this over and then screw this into place here by again rotating the allen key clockwise. like so and now this is at the correct place so it's like um at one level with these bars and now i can also tighten these by again oh maybe this one first by rotating clockwise to make sure that's secure over here as well nothing's wobbly this one's secure already too and now all that's missing is these top parts um so this is obviously on there the wrong way um so i'm gonna have to have to see where this is how this is screwed on there um so i'm just gonna tighten tighten loosen this Ah, okay, so it's connected down here with this screw, so I just need to loosen this screw. Oh, another bracket fell down, so I'm going to pick that up. Okay, now if I look at this, this is in the correct place facing inwards. This one is missing one though, so I'm going to take this from here. um and put it at the same spot so right here and just slide that in make sure it's level and then use the allen key to screw it in like so and now we can look at this and see that this connects like so so i'm just going to take that and i need a bracket for down here so i'm just going to take this hold that here and here, then I can use this to, is this correct? No. Okay. Oh, it's the other way around. Sorry. Like this. Yes. Okay. So I can take this up because this won't connect, but here I can now put this right back. And then screw it in here. Make sure it's tightened enough. And now I'll do the same over here. So this goes on like this as well. Again, I need a bracket for the screw to hold on to. I'm just going to take this. And then I'm going to hold it here. put this on top and then put this screw into place by rotating the allen key clockwise like so and i'm just gonna fasten it with the okay now everything is done i think all we're missing actually from assemblies before I know that these two screws they go in here just to act as another sort of barrier but these ones I don't need but now all that's left which you can see in the picture is these coverings so I'm gonna add those so you need two over here there and there and then two more of these big ones up here and up here and then all these small ones um let me look at this we really only need the gray one up here i'm pretty sure And then two on top of here. And I think one more on top of here. But I think that's everything. It's reassembled. Everything is secured securely. Nothing is wiggling around. So I think I'm done with, yeah, with reassembling this correctly." + }, + { + "category": "inspection_repair", + "name": "User_15_451_2401_1_480.mp4", + "transcript": " Okay, so I want to test if this PC is working correctly. So first I'm going to connect it to the power source by plugging this cable in. And let's check that this is plugged in. And then I'm going to attach the monitor right here. Just slide that on and fasten it. Okay and then let's see. Press the power button. As you can see nothing is turning on so I'm going to have to inspect the PC. So first I'm going to remove the monitor cable again. And then the power cable. And now I can turn this around. And take off the cover. I'm going to place that over here. And then put the computer on its side. Now immediately the first thing I notice is that this is completely loose. So I'm going to put this back in place. Right here, the RAM chip. And I also noticed that another one is missing. So I'm going to take one from that box and put it right here by opening those clasps and Sliding it in and then closing that. What I also notice is that this fan isn't plugged in, as you can see here. So I'm going to fix that. And also this power cable is not plugged in either. So I'm going to look at this and make sure that these shapes align. And then I can plug that in. um also there's a battery missing so let's see if we uh we have one right here so we'll put that here the cmos battery and then this cpu doesn't have a fan actually so luckily we have a fan here and i can um put that on top so it goes like this and I want to be able to connect this and I see that there's a slot there so I'm going to orient it like this and then we can kind of place it down so that these screws are aligned and then using a screwdriver I'm going to screw these into place like so by rotating it clockwise Now this one. This screw. Also by rotating clockwise. And this one as well. Okay, I'm gonna check that it's connected well, and then I can plug it in right here. There we go. Oh, I also noticed that this is not connected via the power cable, so I'm going to connect that. like so there we go snap that into place and also this is just way too loose so I'm gonna move this in and then see that these holes align and I should have some screw here I think this is too big so I have this screw and I'm gonna attach that here I think by rotating clockwise. Maybe this is supposed to go here instead, I think. Oh. Try to take that out. There we go. And then we can screw it in. Like so. Now this isn't loose anymore. And here there are also some units missing. So I think it's these two. And first I'm going to touch this one. So I can just... Oh, that's a bit tight. Just slide that into here. Hopefully. Maybe the other way around. There we go. Have that snap into place. Now the other one. Like so. Snap into place. perfect and now we just have to connect them so for this I have this cable which I can connect here and here and they also have to be connected to the power so this is connected wrongly I don't know what this is supposed to do so I'm just gonna take that out of here and Oops. Connect it here. And now we're missing a power cable, so I should have one here. There we go. So I'm just gonna connect that here. And here. Oh, that's the wrong way. Like so. Now I believe that everything should be connected. I'm just going to give it a quick look again. This is all connected. This is tight. This is connected. These are all plugged in. The RAM chips are in. Batteries in. These are in connected. So I think everything should be fine. So I'm going to put these tools back over here. And I can now close this again. by sliding it in there and then just pushing it down. Okay, and now let's turn this around so that we can connect it to the power again to test if it works now. We can also connect, as we can see, it's already turned on. Now we can connect the monitor. And also the keyboard. Okay. Let's turn this on. See if it's working. Oh, I think I just turned this off. Let's turn that on again. as you can kind of hear the PC is running this opens and closes Hmm. It is on though. Just the monitors. Maybe not got the right source. Yeah, but it's definitely working again. Ah, here we go. Yeah, this might not be. Maybe this is in the wrong spot. No, that was right." + }, + { + "category": "inspection_repair", + "name": "User_15_User_14_411_1010_1_480.mp4", + "transcript": " Okay, so first we can see where the problems are. If we put this into here... you can't move it down so if the workspace were here you can't move this part down so this is wrong and also it usually should go this way over so like this and this is also too loose so we need to fix this and we need to fix this bottom part so that it moves correctly so I'm gonna take this out again and wear probably first going to try and fix this part down here. So in order to do that, we're just going to unscrew this screw. Second, I have to take off my rings. Maybe you can already unscrew that part. It's easier because it has this thing at the bottom. If you hold this, if you hold it and then screw. No, this part. If you hold on to this, then it will be easier to screw. Like this? Yeah. we go okay so i'm just going to put this over here and then take oh so i'm just going to take this whole thing power okay um How did you even get this together? Okay. So I'm going to try and slide like this. Slide all these pieces out. Okay. So now to reassemble, we need to put these ends of the springs on here first, and then we can put this here. and fasten it like this and then for this part i'm going to put this long part on here first because it would act as a separator and then this one goes in the middle So I'm going to slide that in and then push this down. And now the separator that would actually go here, we lost. So that's not a big problem though. So we're just going to press this down. Yeah, we're going to press this down and screw this screw back in. Maybe it's a bit easier if I hold the bottom again. There we go. like that and now we can attach these springs first make sure they're in the grooves and then we can attach them to this part right here and then if I turn this around again making sure it's in the groove and then attaching it to this part right here and now if we put it back in here This is already incorrect, how it should be. Just this part is a bit loose, so we still have to fix this part. So in order to do that, we're just gonna take all of this apart. So just unscrew these. And this. And this part. okay so i'm just gonna take this off so the way this is supposed to work is that this round part goes on here as you can see there's the markings from where it's moved around so we're gonna move that in there and then these parts connect through here and through here I believe and now we can put this top part on top again this is still moving around a bit like so and then I don't know where this came from I think here nope it should be here like in here no no it was Where was it? I don't remember. Oh, no, I do. It should be in here. Okay, now we can put the top back on. No, the other way around because it has these groovings for that to sit in. And then I'm going to take these screws, put them in the holes, and then screw this part back on. by rotating the screwdriver clockwise. The same over here. Oh my God. So again, just rotating the screwdriver clockwise. And now all that's missing is that part, which we're also going to screw on top. Yes. And by tightening that part, you can make sure that this doesn't move around. So if I make it tighter, it won't move around. And if I loosen it, I can move it to like here or here, whatever I want to. So let's see if we've now fixed everything. Maybe we can also plug it in to see that the light works actually. So I'm just going to take this plug out. Plug this in and then we can turn it on. See that it's working. And now you can move this around again so that if I want to put light on something over here, I can just move it around like this. I can also, if I loosen this part a bit, if I loosen it, I can possession it however I want and tighten it again by rotating clockwise. And now the whole lamp is fixed again." + }, + { + "category": "inspection_repair", + "name": "User_16_407_0511_1_480.mp4", + "transcript": " so i'm gonna check this table this is missing bolt and this bars is not stable also missing bolt here label with wrong position is instruction so we're gonna repair one by one first screw in some bolts here use the screwdriver first part of the mixing bolt is solved And tear it out. And this bar says round position, so I'm going to change the position just like this. Screw in. Make them tight. Good. Make them tight. No, this bolt is round bolt. So I'm gonna change the bolt. It's too tight, round bolt. Let's check. here also, right, here also, so, right, and tight everything, everyone else, every bolt else, stable, now, put the cover on, Next, here are some mixing bars. Also, glue them tight. Remove the cover. remove the cover and tighten up you can see here some problem here also the bolts are not tightened just gonna remove this to see where is the problem It seems just fine. Change one bolt. Change the bolt. Tighten. No? So maybe the nut is not aligned with the bolt. Let's remove the bolt again. Align the nut. Try to tighten them up one more time. No, it's better now. Okay, it's tight. Let's put the cover. They don't have the big cover so... And next, missing some bolts and not stable. Not stable, the problem is solved. Remove this. And here missing bars. We can see here, so one bar here and one bar there. So I'm gonna use some bars here. First, the run position is also fixed, so I'm going to remove this. Now, this bar can be down by doing low. Next is this shape stuff. Let's see if we have knots. So, we can use the nuts here. Oops, sorry. Okay. Other sides. This has beads. make it tight make sure the position is right and tighten also tighten this good And then, do we have a cover on it? No. So, it seems that we don't have a cover. So, let's have a cover. Cover this. Yes, it's covered, covered, covered, covered. Not covered, not covered, right? Good. So, there's missing bars. It's also fixed. It's also fixed. Remove this. Now, everything is okay. Stable as well. Stable. Good. Clean everything. Put the unused thing down." + }, + { + "category": "inspection_repair", + "name": "User_16_411_0210_1_480.mp4", + "transcript": " Okay, good. This is trolley. I'm going to pick up a table. Open the door. Move the trolley. Close the door for a bit. Open the door. Open the door. Close the door. And put this table on the trolley. It's a bit heavy. Be careful. Put it on. Push it back, open the door. Sorry. Close the door. Put it back. Room 411. Open the door. Hi, sorry. Back in. Back in the room. Close the door. Might need to turn on the light. and put the table out from the trolley the trolley aside now let's see this table have 1, 2, 3, 4, 5, 6, 7, 8 bigger screw Let's use the tool. See which size fits. Four millimeter? Yes. One by one. Take them off. Remove the first screw. second school. Third one. Fourth. to another side. Number three. And the last one. Hold it. Remove it. OK. Removed. This is handled to adjust the height. Let's move it for a while. And the next is the smaller screw. Should be three millimeter. No. Remove. Hello. Two. Number three. Now this metal plate can take it out. And then I think I can put this little table, metal table outside, out. Let's see. Get on like this. This has been removed. But this part This mechanical part, it shouldn't be removed. Now, let's put them back on. First, the table. Careful with your hand. So align them. Now, with the number four, put it back on. one by one. Realize. OK. Do you want to record it? Yes, I am. Sorry. Yes, I am. It's going to be hard. Let's use the tool. Is this aligned? Yes. Let's go with another one. Turn the other side. Good. Another side. not force them to be aligned should not be like this another side Close them a little bit. This one, that's where I can lift it back. Lift it up. Let's try one more time. Bye. right back Mm-hmm. So trustable. Is that possible to make this part shorter? Oh, how do you do that? You just open it out. but if it's too long it cannot fit inside i should put it put it in help. Yeah. Okay. Yeah. And then put it back. Did you show the crank? Yes. I just showed it. Thank you. Good. Now it actually fits. you Next. This one. a small metal plate back this is easy work This one. Okay. Screw them tight. Yeah, wonderful. The towel. Open the door. Close the door. Lock the door, open the door. And put it in. Close the door. Take that table off. Put it back. Oh, it's heavy. Good." + }, + { + "category": "inspection_repair", + "name": "User_16_411_0910_1_480.mp4", + "transcript": " In this experiment, I'm going to test the computer. First, use this trolley to get the computer. Going out of this room with the trolley. Close the door. Push the trolley. This room. The other computer. Put it on the trolley. with the cable, close the door. Hi. Sorry, I'm recording, so I'm not joking at you. About 40 minutes, I have a key. I'm not sure if that's okay to open this door. Do you need a computer, or? Sorry. I just need you to let me know if you're going, because I don't have the key. Ah, okay. You don't have the key. No. Okay. I might not come back to this room. You need to lock it now? No, I don't need to lock it now. I'm in room 411, so if you are leaving, just lock the door. Okay. 411, it's over there. If you're leaving, you can tell me I'm here. Yeah, sure. Thank you. See you. Sorry. Sorry, one question. I'm recording, but I was interrupted. Yeah, that's okay. That's okay. I'll continue. Yeah. Okay. Can you do that later? Ah, cool. Are you going here? I'm going to 411. Thank you. Get the trolley in the room. Take the computer. Level it up a little bit. Let's see where I can plug in. Oh, here it is. Plug in. the computer. Let's see which is the path. And do this way. stay off this working plug in the power turn it on let's open this it's weird So that means some problem with the computer. I will try to fix this. Let's lay down the computer first. Better fix the problem. I need some screws of this. So here is the toolbox. This is the size of the screwdriver. First, I think we need to remove this. Remove these three screws first. And also here, another three. We can remove the handle. Let's put it back on. are the same remove it remove this And also this and this. And then the handle can be taken out. So take out the cover, the front cover of the computer. Put it aside. And remove the case. the main case from the side by removing remove this two screws push it lift it remove it put it aside let's see how can we fix the problem there are more screws So use screwdrivers to remove them to see what's going on with the computer. Removed. Removed. Put it back on for a while. Continue. Try to remove every small thing. It's a very tiny one, so be careful. It's all removed. So here is the DVD drive. Let's see, it's connected to the motherboard. Another side is connected to the main power supply, which connects to the motherboard. This line coming from the power supply also connects to the motherboard. And this is the hard drive. There are two hard drives, but I think it's not useless. It's mainly used as the hard drive above. I'll try to connect it to this one. OK, it's connected. which is connected to the power supply also another side is connected to the motherboard also and the thing below here is the LED light and the power button the power button and the LED light connecting to this line which goes to the motherboard correct and this one is this fan the fan is connecting to the motherboard correct we plug that in and next we try to connect to the power and let's see if it's going on no nothing happens see there's some problem let's plug out let's see if there are any problems with the fan the fan can be opened so it goes normally it goes just fine the problem might not be the fan but we try another way maybe this let's remove every I believe this is the the memory stick. Remove it. Remove this, another memory stick. Wipe it and plug it back in. Once you hear a click, also this one. Push it. want to hear the click let's try it one more time if it's going normally click power on nothing happens let's plug it out what is this part? this is some holders which are not directly connected to the computer so which not effect anything but anyway we will remove this bar to see everything more clear Let's see. The motherboard connecting to some plate. And this should be the CPU. And this is the power supply. Oh, this is not plugged in. So this might be the problem. Let's see if that fixes everything. So we connect into the power supply. This line goes from here back to the power supply, which means the power supply can give power to the motherboard if that is correctly connected. Plug the power back. Turn it on. great the LED light shows this goes off one another time it goes back on everything work just fine let's try this DVD drive great DVD drive working well the CPU the fan from CPU working well the main fan working well you can see the fan is running some wind coming out also here and we hear some beeps which means everything is working just fine turn it off Cut the power, plug out, and put everything back to the position where it belongs to. Screw it in. Screw it in. And put the little screw back in using the screwdriver. This is a very small one, so be careful. Back on. This is for the hard drive. Back on. Screwdriver back on. and this is the DVD drive yes only the DVD drive screw it back on screw it back on no? Let's put the main cover back another way. I'll show the difference. Push. Oh, that's true. Doesn't feel so good. That's fine. Everything's fine. Put it back on. This moves clockwise. Also this one. Put it back on. it should not be a problem so let's just try one more time it fits also this one perfect fits and then let's put the Cover back. Let's see which way is this way or another way around. It doesn't matter, I think. Yeah. Because it's the same. So one back. Okay. Yep. Goes like this. Might need a screwdriver. Align to this hole. Screw it. In. This one, yes. Go in here. and put this back on a little bit and another one to align to get the position right first and this correct and this final one from this side That's correct. And turn the computer one way around. Here's another way. Screw it a little bit with hand. align with this hole from the cover. So this hole goes to the cover and these two holes connected to the main body of the computer. So we can fix the cover and the body together with the handle. on this one on this one also on fix all of them make them tighter screw it in make it tight also this one so everything is fixed so let's put the screwdriver back to the toolbox Plug out the power. Put it back. Put the computer on the trolley back. Good. Wipe it a little bit. Lower down the trolley. Level with this handle. Good. Move the chair. Open the door first. Push the trolley. Close the door and the light. Push it back to the computer room. Stop here. Open the door. Take the computer first. And also the cable. OK, and then it's finished to fix the computer." + }, + { + "category": "inspection_repair", + "name": "User_16_411_2410_1_480.mp4", + "transcript": " okay recording started i'm going to repair this windows pc with the instructions so we need to check if this pc works i think i have to first connect it see if this works well plug in let's see it sounds really terrible no I think it's definitely not let's plug it out I'll put this there. First, it's disconnected to the power and repair box is ready. Check the cabinet door. Check it. There's something missing, obviously. so check the power unit i think i have to first remove the cabinet open this okay first we need to remove this handle i believe Or not. Check it. Quick check. Loose this. Use this longer. Bigger. Screwdriver. Loose. One of them. Two of them. One of them. See if this can be opened. Nope. So we have to Loose all the screws. All the balls. The handle first. Second. This. And this. Secure the handle. This one side. Turn it around. Pull the screws away. Turn it. Take the handle out. Okay, another one. Third one. one more three left one two three if it's tight okay loose them let's remove this and pull the screws Remove this front. And put this here. Screws are here. 1, 2, 3, 1, 2, 3. So 1, 2, 3, 1, 2, 3. Great. Let's put it here. This here. Let's see if I can open it. This can be opened, but not now. I believe I have to remove the key, which we might need this. Use the small screws. Small bolts. One off. Two, three. Can this be removed? Not yet. Let me see the instructions. Cables, Allen keys from the outside check if they opened. Plug in the power. Does it start? It does, but there's some problem. Disconnected to the power. Yes. Open the door. We have to open the door. Check the power unit. Connect to the monitor board. We have to open this part. But first, I think, I believe we have to... This screw is over here. let's see how can we open this maybe we have to do it step by step yes so we can Let's check if we need to unscrew this one as well. So this part is still unable to open. It might be need to... Let me check. Yes, it can be removed now. Let's open this. and i think this doesn't need to be removed so let's put it back on okay this is from the other side screw it back on as well as this one let's see what is missing so we have a big fan up here big fan is power supply this should be cd drive let's put it the same position like this I think first I need to remove this part by unscrew this three as well as those over there it's a little bit tight let's check yes I believe I have to I'll screw them. I'll screw them to make this have a better view. So put it here. Small bolt. Put it here. This small bolt. Put it here. Good. And over there as well. So, turn it around. And this has two screws. It's a little bit tight. So, screw this. So, it's this one. Unscrew this. Okay, now it can be removed. Let's see if that's correct. Let's check. like this which means it goes like this way Okay, it goes that way, so just remember everything. Let's get rid of them. Let's just put them outside. Okay, let's check. I'm gonna check it. First, check if the power unit is connected with the motherboard. The power unit is this. Let's check. Let's check. According to this. This is unconnected. Check one by one. I'm missing a lot of things I believe. So this part is connected to the No, so we need to plug this in first. There is another one. This is the fan. Fan is connected to the motherboard. No. This is the fan. We need to connect this white thing to this. Be careful. I think I need the light on which you can see more clear. Yep, this means connected. and if the cmos battery is connected let's see where is this no it doesn't have the battery so we need to find it in the box this is the box some part this is the battery so i found it put the battery on click check are there any cables not connected to if yes what can be can they be connected graphic card if any device such as graphic card are in the way just remove it let's see if this graphic cards this is not able to connect this RMT this motherboard there is a after two REM chips two REM chips inserted REM No. So we need to find the REM chip. Let's see. I believe this is the REM chip. So this is connecting to the here. Let's try it. Okay, I believe that is the sign of this motherboard is I need to remove this Rapid card. Let me see how can this be removed. Because you can see these are not able to connect. If we put it here, that might be one more option. Could be. No. I believe this needs to be removed. Not the Not here. Not the way you want. okay this can be so the graphic card doesn't need to be removed for now so But if I want to be sure it's 100% the same as the instruction, this part needs to be removed. Let's see how can this be removed. And the screwdriver on it. Move this bolt. Okay, it is removed. So it must be more easy. Let's put this back on. Yes. And another one connecting to it here. put it back for a second and next if the hard desk mount is connected hard desk should be put in here so which means this is the hard desk If we want to install this hard desk, let's put this back on here for a second. Don't forget. Good. Let's see. How can we pull it? How can we install this hard drive? There's some cover on it. Hmm. Oh, is this the hard drive? No. Nope. So this must be the hard drive, right? Looks like this one. Let's see. this might need some not use available harddesk amount into the Let's see which tool can I use this little. Mm-hmm. Hmm, let's remove this part first. How do you connect it to attach to here? Let's see. Oh, there is some screws, but here is also some screws, so it's not easy to... So if this is the hardest, what is this? Let's see. It's connected to it at first. there are small screws over here there are like there are cables there are three cables which looks like identical but with the same different length I might need to try the shortest so here is the way plug which is connected to here at which part? C it's just blocked but I can use This one is connected. And here is also some different... Oh, this one. Yes, using this one. Connected. And next is This must need to be connected with the CD drive. So let's put it later. Let's figure out how to connect with this one. Let's remove these small balls first. Sorry. Let's figure out how do we, how can we put this back? so this might not be the proper one that's why we are going to use this one here right and i need to put some extra screws for it see we only need four screws four bolts we yes did you find some extra bolts if there are any bolts inside no so let's find out in the box yes there are many bolts are available so let's pick four one two three four okay now i'm going to use little bit also here so here as well Okay, let's put it on. Let's see. Yes. And plug this in. There's a small one. Let's plug it in first. L shape. And this one is... I use this. Looks like more. Plug in. Plug in. And put this on. put this on and no need to show it back in first and next connect to the power and data cable this data is there are two parts so the first part is here here and here there are three so Yes. Power and data. Good. And the CD drive. I don't have a CD drive because it's empty, so I'm going to use this CD drive. Which way? Doesn't matter, Sims. Let's put the CD drive back. Go this way. Okay, good. But this also needs to open here. Yes. So we need to use a screwdriver to loose this to small bolt. it out. Put this hard drive on. I also need four. I'm gonna choose some bolts. here and hold with this line It might be too big for this hole. I'm going to choose a smaller one. Here's another one. Much better. Let's try this. It's a similar size, it seems like. I'm going to try there. Oops. OK. Here as well. This one. Also here. Put it in. Make it stable. here, need to be stable. Stabilize over here. Also here. Okay. And put them on. Alright. And plug. Sorry. Plug back in. Let's see, this is longer side. L shape going to here. Let's see if there are any missing. Because it looks like one. Okay, this seems like using not this one, but this one. Okay, and need a cable. Size is the same. So choose this one. L shape, upper right, left. Okay, we'll just connect also here. Let's see. Another thing. Good. R-E-M, R-E-M, harddesk, harddesk, check. CD drive, CD drive, check. Back on these two bolts. So here also. Use reload. Tighten this up. As well as this one. Tighten. Data power. Data power. Check. I'm going to tighten. Here is one, so I'm going to tie it over there. Cut the extra. Be careful, don't cut the line cable. Good. Let's cut it up. Let me check. Bound it together. Right. you you OK. What does this do? It doesn't do anything. OK. If these are removed, Replace the open slot with a grill. If the cabinet is open, quickly connect the power. Check if PC start. Be careful. OK, I'm going to just replace this first. Give me this. See. Maybe this is too thick. So it cannot be. Let's see how it kind of weird. How can we replace this part? Are they able to be replaced? Now we can try it. let's unscrew this and the rest of them unscrew with my hand okay Don't use this. Nope. Only with hand. Okay, let's try. They're building together. So if these are removed, it's going to be tough. Are they able to? Let's try first. Let's try if that can work. I believe you said this one. Yes, I believe it's the one. This is hard to remove. And it's harmful for this. Let's screw it back on. School driver. make it tight and tight this back on I believe I can remove this one instead because this part is not gonna be used so replace it remove this place with this one Great, now it looks much better. And put the graphic card back on. Great, clicked. Bolt to hold it. Make it tight. Tighten them up. Good. Tighten them up. Tighten everything up. Yep. Check. Check. Check. Check. Check. Check. Everything is tightened up. This is the internet card. This could be also CPU. No, not CPU. This is CPU. Express card, hard drive, CD drive, fan. So, there's also one more. Let's see where can this go. It doesn't look like one. Maybe this. No, because they are connected. Let's see. Let's have a look. Have a look. Let's put them aside. Try if that works. Turn on the PC. OK. Let's try it. Use the cable. Connect to. Need to be careful. Plug this side first. Plug into the power. And turn the power on. Sounds great. Sounds OK. This works well. Okay, let's turn off the power. Disconnect it. And now, let's put it aside. There are these connected parts. Nope. Yes, remove them. This cannot be removed. And that part is removed. Oh, shit. So bright. And put the cover back. Sorry. Mm-hmm. and screw them back on maybe from the back Oh, I forgot this one. All right. This is a huge one. Need to be put on first. There. Okay. Next also. Next. Next. Good. And the pool to cover back. Okay. Screw them. It's a screw. Here. Okay. Good. And for the upper part. And using the handle. Right. Yes. Right. I mean, it actually looks like this way, right? Just this way, okay. Okay, this way. Right. Tight everything up. Tight them up. Next is the upper side. Do it like this. Upper one. Good. Good. Now, let's put the tools away and connect them to the monitor. See which cable. This one. Yes. also connect to the computer power and let's see if they C. Sounds working well. Looking just fine. Let's see. Let's try different Let's try one way around if they are anything. There must be cable problem. OK, that's it." + }, + { + "category": "inspection_repair", + "name": "User_16_411_2510_1_480.mp4", + "transcript": " I'm going to repair this PC. First, let's open this PC by using this bolt. Put it on the other side and open it up. Let's put it aside. Now let's see. Follow the instruction. Plug in the computer to check if that works. We need to turn this PC around. Let's start. Let's try to connect with the computer. It sounds a little bit weird. no so there must be some problem with this pc i'm going to turn it off for a second plug out and next we have to disconnect the power cord disconnect it and get the tools to repair Open the cabinet door, inspect from the inside, check if the power is connected. So it seems it's not connected with properly. So here's the power cable force. One, two, three, four. and the bigger size power keyboard is connected to nothing and the other thing is connected to the motherboard which also connect to nothing so let's first check if the fan check if this part is successfully connected let's try to plug in let's put the light on Make sure. You can see there's four cables. check if the fan unit is connected check the simos battery let's check everything this seems like connected to the fan which is connected to the motherboard this must be the cpu this is not properly connected let's plug everything back on login which is connecting to the is plugged in let's see next plug this in okay good now let's see this part is not plugged in here the cpu fan must be plugged in here It looks all right. But first, let's check this part. There are seven. Oh, the CMOS battery is not properly on. Let's put the battery on. Turn it over, turn it around. Put the CMOS battery. And let's check the fan is connected. CMOS battery is connected. Is there any cable not connected? If yes, can they be connected? So do we have a graphic card? I think we don't have a graphic card. so we do have some RAM let's plug in the RAM should be over here let's try to connect this will run yeah, plugged in also here the blue one okay Okay, so the memory card is plugged in. It's hard desk mounted to the hard desk and CD drive. Here is the CD drive, which, here is the CD drive. This should be the hard drive. What is this? Some other drive. This is the CD drive. Let's see where can I put the hard drive. So there is a bigger bolt. Let's take this out. Using the screwdriver, let's use this one, the big one. No, let's use the small one. Take it out. That will be much easier for us to see what happens. okay the front is moving out let's see which is connecting to this one which is this four bolts let's screw them let's take them out So this is the hard drive. We have to connect into the motherboard and mount it into the computer. So now this is removable, but something stuck here. what is this let me check no this is locked this is unlocked So very interesting. Okay, there are four, but this is not connected. One part is not connected. Let's figure out which part we need to connect to here. this goes up here which is directly connected to the power supply this should not be the same so let's find another one so in this single plug we have two separate like this with orange line yellow black red so we don't have a super identical one so the other part is connected to here and what about this one This one is connected to here. Let's try this part. Plug them in. Let's turn this around. Put it out. And let's see, can we uh-huh so this two part is belong to this two different this is this shape and we have another shape should be like this but it's not I think. okay so there must be this should be plugged in here this should be plugged in here plus two here okay good now let's put this hard drive back on which need one two three three different connections which goes which way let me see it could go here or here yes this could be a position but i think that here also is available it's a good position for this So this must be the part which can be pulled out. Let's put this part out first. this part is put out this is connecting to here should not be moved so i think i can put it back on because this small thing is not relevant it's unrelevant so let's screw them off If not, we can just lose them back. Let's see which part do we need for this. I think this can be connected. Yes, this part. And I think we need a red cable. This is for the power. And we need one for the data. ok let's see so this part doesn't have one second this is two different parts this is the which is the power the light it's plugged in So this kind of cable needs to be plugged in here. So that's the reason I believe we need only one CD player or so this is cable for here it could be a cable for here and another cable for 8 pins should be the cable like this so it's too big what about this no What kind of cable is this? So this is the type of the cable. Connecting to here. See. Also, this hard drive is not connected. This could be interesting. This is interesting news. Do we have another cable for this? Let's turn one more round. for the supply this for the hard drive connect to the power power connect to the motherboard CPU connecting here the memory power 2 power 1 data so this is one data this is one another connecting to here let's check we have extra cable for data this doesn't look like some cable but i think it can be plugged in here or somewhere no no This is some people looks like this I Think we can try to start the computer first to see if this working properly because everything need to be connected is connected Let's see if just have a try to plug in this no, the size doesn't match it looks like this nowhere looks like that so let's plug back on back in this pink like stuff is this but they are all connecting to some other place so let's just plug in everything and try to put on to see if this able to connection let's see if this able to start So the start button should be like the lower one, right? The power is not on. looks good CPU fan no keyboard yes of course no keyboard because I'm connecting to the keyboard yes it can start CPU fan error it doesn't looks like an error looks fine to me ok let's stop the computer Turn off the power and plug out. And also the here, plug out. Now one thing left is put the hard drive back. is it only can go this way oh no this can go directly straight down Lock them. Lock them. This is properly set. And it can also be locked. So this here. here to here and put the back to here plug back in using this because it's the most Not the same, they are the same. Okay. That's good. Everything good. Screw this. Put this screw. and put the cover back Good. And should we start? not should be from the inside But this looks like from inside. No, it's just from inside. Okay, this must be from the outside. So just screw it in. Okay, good. And last, put the front side back. Just by pushing it. Okay, good. It's fine. Plug in. And plug in here. Start the power. Turn on the turn on. Good. This can be started. And next. Yep, good. It's working. This is also working. Working just good. So, that's it. Turn off. Plug out. Lay it out. Lay it down. Stop the recording." + }, + { + "category": "inspection_repair", + "name": "User_16_412_0710_1_480.mp4", + "transcript": " In this video, I'm going to disassembling a computer. First, leave this room with this trolley to get a computer. Close the door first. Start with room 412. Going with the trolley. Careful. And in the room 414. Get the computer. Open the door. Take the computer back to the room. Open the door. Take the trolley in. I will do it on this table. So this table needs to be clear first. Put the ruler aside. Put the pen aside. Put the chair away for some more rooms. Keyboard aside. Mouse aside. and up the trolley make it more easy to move the computer ignore the trolley put the trolley aside here for a while Let's see which range do we need. I think it's 3 or 4 mm. There's screwdriver. Bigger size and small size range. Okay, I'll get the tool. It should be in another room. Room 411. Turn on the light. Close the door. This is our school drivers. I might need all of them to try if it fits in the range. This could be no sole. Check if this fits. Close the light. Close the door. Going back to the room 412. Close the door. Turn on the light. And then start disassembling this computer. put the chair aside and don't need to sit down. So, use this to loose the screw. First one. Second one. Take off the handle. There are two more identical. Loose them. Use another one. Oops. Drop down. It's there. You need to be careful. Take this window out. And there are further more. brown side last one from the handle OK, the full handle coming out. And then the case, the side. The side. Need to be careful. This is the longer size. Again, this one is longer. So put this side. Next is. from here so if I assemble this back I should put it here put it aside for a while and the third one and the fourth one can this be removed? there should be one more screw in the inside yes I can see it's inside of this apple sign so let's move to the front side can this be removed? also no back also no so let's turn around of this computer be careful there are more screwdrivers over there lay down another side another side there are more four more screws with this screwdriver to remove first one second one third one final one i believe this can also not be removable because also there are an apple sign which means inside of this sign there are more Okay, let's see the back side. There are more screws in this side. Or it could be smaller. This is bigger size. No, this one. Can we move this one? One by one. This is smaller size, so I'll put them in different position. second one third one is from the back side there are some screwdrivers here is the screwdriver Second one. Third one. It's connected to the inside, so I'll remove this screw later. So this is all screws from the outside and handles. Now I'll open the inside. Pull this to open. This is the inside. we can see here are more screwdrivers a lot more so let's start from here because there is one screwdriver we have already taken off so remove this with the motherboard and this screws connected to this fan this fan is for cooling the CPUs I believe which connect to the motherboard let's try to take off use this screw let's see can we take off this board some chip from apple or some company this side is that removable yes this board can be removed Next, try to remove the motherboard if possible. This side. Next, we lose this. Connecting lines. to this maybe i don't know connect to the power which also connected to the control system this is all Let's see if there are more screws. Nope. I'd like to take the battery out first. Take this battery out. Let's see if we can put the motherboard okay let's try to move this memory card pull them aside by clicking these two buttons let's try to take the cpu find cooler out let's see if it's possible no because there are more screws connected to which blocked by the metal cooler so let's focus on this hard drive I think or DVD driver Be careful. They are very identical. I have one more tool. Take this out. And then we can take off the hard driver. Oh, this is DVD driver. Let's put this aside. Let's try to remove the power system. It's kind of hard to use this to reach this screw. Let's try this later. You can see there are some loose screws inside. I don't know where it's coming from. This is a hard drive. Very inside. So it's very hard, difficult to take off. Let's try to move this big fan. Remove this big fan. Is that possible? One, two, three, four. Let's try it. And this one. I believe this is every part that I can assemble from this computer every screws every part the battery take it off the memory card the plate the fan the dvd driver the mother motherboard and the scooter cannot be taken off so let's try to assemble this everything together everything back to where it belongs Let's put this back. It's not going to be easy. It doesn't have magnetic. It's too big. Try it. Give it a try. Or that comes to the last. Let's try this. This big one first. with another one first. Great. First screwdriver comes on. Next is this. Let's put in the last one. Next is this one. This back. Cool. This one inside. Dropped out, but it doesn't matter. Make it tight, but not so tight. And then this one. Okay, it's coming back. It's fixed. good next put the battery on this is plus this is minus positive and negative put the battery back on put the memory stick back on just push And... Hardly push it. Yes. Back on. And then put this back on. And this way. Push it. screwdriver fix this screw back here is another one to the motherboard it's hard to get back on so let's leave it in this This little fan here. let's see if we miss anything Another one. And this one. Oh, here's one more. So this into there. you Okay, let's put there. Push it. Now we lay down one side. Put everything screwed on. Space range. Let's see if we are missing anything. If we are missing anything. Oh, there is one missing. Because I used the one from outside. So. Anywhere. Let's have a look. I believe there is nothing left also than this one. This one is really hard to back. Give it a try. Give it a try. Let's try. Sadly no. Let's see if we're missing anything. Check. Here. Yes, you're right. This one. Try this one. They are very tight in each other" + }, + { + "category": "inspection_repair", + "name": "User_16_412_0710_2_480.mp4", + "transcript": " okay let's continue screw this screwdriver back from the back from side yes it's a side let's continue with this and this Let's turn around. Be careful. This four. Second one. Make it tight. third one clockwise make it tight the last one clockwise make it tight okay and then put this back here's a half here goes another half The handle. The screwdriver to tight first of them. And this side. Okay, good. Turn around. Another four. Last one. Okay, good. Now turn around one more time. Screw them first. Okay, it's tight. Good. Next. And the last one goes here. Good. Another side. Put it on and turn around through the last three of them. I think it's finished. Let's take the trolley. Level it up a little bit. Put this on. Push. Open the door. Take this out. Close the light. Take this computer back to the room 414. Take out the computer. Put it back here. Move down the trolley. return to room 412 then clean up everything put the chair back keyboard and mouse bar back and the pens and the ruler back And it finished." + }, + { + "category": "inspection_repair", + "name": "User_16_414_2910_1_480.mp4", + "transcript": " Now, I'm going to repair this table first to level this trolley up. Put them to stop. now I'm going to see which part is at the wrong position for this plate this shape and also this one is wrong position first remove this part it's already dropped so left side here also It's been taken out put the bolt over here and check if these are in the wrong position these two bars looks like they are in the wrong position so gonna need one more no it's too big I'm going to use one of those. tighten it up also not tighten too much also here this plate should be here so I'm going to use this one thing there are much more inside let's see sphere 2 we need to also I'm going to use this I'll put them inside I need some screws to turn them up. One, two, three, four. Good. A lighter position. Here is one missing. This should be here. I'm going to put one more thing back. Let me see. Here's one. Here's one. This one will delete. here is the one down here we need 1,2,3,4 turn a little more around This is about here. There's a lot more. I'm going to use it later. What we need now is... Unline the position. now we can tight we can tight also put this part so this little thing should go down here this position tie them up I'm going to do is using a screwdriver What I do is first remove this. This cover. Remove this. Unline the position. see All right. it's And now this part. Just remove the cover. Remove the bolts. Line the position of this. Put the screw in. Put the bolts in. Tie them. time time time as well. Good. So I did. So the plate. Good. put the cover back cover here as well what else? a small cover Let's put the extra thing back into the box. Put the tool back into the box. Check if anything missed. There are two to this side, bottom, top. This is fixed." + }, + { + "category": "inspection_repair", + "name": "User_16_451_1302_1_480.mp4", + "transcript": " okay so now I'm going to repair this new trolley first let's put on the gloves and I will put on another gloves checking the instruction information letter document this is the correct four wheels which is there are two but there are two missing and there are two here and the base need to be assembly successfully need two connections and the vertical bars need to be changed the frame just need to be tightened so this is the tools from there all the allen keys from the small size to the biggest size so the bolts key and a screwdriver so first I'm going to check put the basement away start from the wheel it's already assembled so let's take it here the horizontal bar frame to the side first I'm going to attach the wheels first so for the wheels back in back in the room close the door might need to turn on the light and put the table out from the trolley the trolley aside now let's see this table have 1, 2, 3, 4, 5, 6, 7, 8 bigger screw Let's use the tool. See which size fits. Four millimeter? Yes. One by one. Take them off. Remove the first screw. second school. Third one. Fourth. to another side. Number three. And the last one. Hold it. Remove it. OK. Removed. This is handled to adjust the height. Let's move it for a while. And the next is the smaller screw. Should be three millimeter. No. Remove. Hello. Two. Number three. Now this metal plate can take it out. And then I think I can put this little table, metal table outside, out. Let's see. Get on like this. This has been removed. But this part This mechanical part, it shouldn't be removed. Now, let's put them back on. First, the table. Careful with your hand. So align them. Now, with the number four, put it back on. one by one. Realize. OK. Do you want to record it? Yes, I am. Sorry. Yes, I am. It's going to be hard. Let's use the tool. Is this aligned? Yes. Let's go with another one. Turn the other side. Good. Another side. not force them to be aligned should not be like this another side Close them a little bit. This one, that's where I can lift it back. Lift it up. Let's try one more time. Bye. right back Mm-hmm. So trustable. Is that possible to make this part shorter? Oh, how do you do that? You just open it out. but if it's too long it cannot fit inside i should put it put it in help. Yeah. Okay. Yeah. And then put it back. Did you show the crank? Yes. I just showed it. Thank you. Good. Now it actually fits. you Next. This one. a small metal plate back this is easy work This one. Okay. Screw them tight. Yeah, wonderful. The towel. Open the door. Close the door. Lock the door, open the door. And put it in. Close the door. Take that table off. Put it back. Oh, it's heavy. Good." + }, + { + "category": "inspection_repair", + "name": "User_16_451_2301_480.mp4", + "transcript": " Now, I'm going to inspection and repair this desktop computer, this PC. Now first, I need to test if it goes well. Connecting to the power. And then connect to the monitor. Yes, they are all connected. Start the computer. Nothing. So this disconnected to the power, disconnected to the monitor. first see the outside this can be opened that's why we turn this computer down down the computer open the outdoor away open the cabinet check if the power unit is connected this is the power unit need to check if it's oh this is not connected so first connecting the power unit to the motherboard is connected next uh this is the fan this is unconnected so i'm gonna connect the fan which needs a screwdriver to fasten in the screws is fastened so the fan is connected to the motherboard and then check the cmos battery is connected the cmos battery which is dropped out is here i'm going to put the cmos battery back on the motherboard click it's connected to the motherboard the battery check if any cables are not connected check check check Okay, are there two RAM chips? So there are only one, so I need to take one RAM chip from the toolbox. So attach another RAM chip. the RAM chip is connected to the motherboard and the hard desk both connected to the mount this is the hard desk and there is another hard desk it's not able to fit let's try another position okay this can fit here since this hard disk is bigger than this so this need to be in here this need to be here connect into the cable this on the shelves both of them to here and this is connecting to here and this one is here and this is another cable connected to here which is What is the difference between this? Connecting to the table to another hard disk Connecting to the motherboard Yes. in this case it's empty so we need to connect it check This is empty, so it doesn't need another. This is NVIDIA graphic card. So it's a CD drive available and functioning. This is the CD drive. It's not mounted. So I need to use this screwdriver to fit the tool to tighten this thing. Tighten the screws. Using the screwdriver to fasten in the screws. There is another cable for the CD drive which we are going to use in this cable Which is right here. Here's another. Everything is connected. So are they able to bound it together? Yes. Most of them are bound together. So while the cabinet is open quickly check connecting to the power. yes connecting to the monitor since the cd drive is not properly connected so i'm going to disconnect it disconnecting to the monitor plug out the power and check where is the issue The SSD is connected to here. This is the CD drive. It should be here. I'm going to get this cable we need to connect it here Let's test it one more time. Yes. now the CD drive works connecting to the monitor let's see if there are any other problems since this is not connected so I'm gonna turn off the computer plug out also plug out the monitor let's see what is the issue the RAM is connected the fan is connected the power unit is connected another fan is connected this board is connected let's turn it around and check if the cable is properly connected so there is nothing so I didn't need to here might this is the issue it's gonna change the position of the hard drive connection disconnected this and reconnecting this to here This is not connected. So this, this. The right is connected to here. Maybe here. which way does this go i think use another table similar so connect into this green blue one Let's try one more time. Turn around connecting to this. and then connecting to the power cable Yes, it started. And the CD is working. Everything is fine now. the skateboard doesn't need because this is the empty and the two hard drive and cd drive are connected to the motherboard fan is connected to the motherboard two fans working well the power supply is connected to the power board and battery is on two memory rem chips are also on cd drive working well the display shows something so let's turn this off plug out plug out the monitor so that's why we can remove this part Disconnect it and remove. And connect it to here again. Good. So nothing is changed. Remove the empty part. or attach them it seems there is something here so let me check if I can attach this not attachable this is very loose still check let's see if I can get the power for both of them Connecting to the power of this small hard drive. Connecting to here. So let's try one more time. Since we connected to a new hard drive, so we have a SSD hard drive. One, two, three plus this small one. And the CD drive also connected. Let's see. Yes, the CD5 working well and the computer is started. Okay, now this means everything is prepared without any losing part. It's connected. Turn off this, plug out. Plug out, disconnect into the monitor. Then close the cabinet. Yes. And then test the final time. Connecting to the monitor. Yes, the City Tribe working well. yes the PC has started okay so then turn off the PC plug out the power plug out the monitor turn out the monitor and test is finished successfully" + }, + { + "category": "inspection_repair", + "name": "User_16_User_1_411_1810_2_480.mp4", + "transcript": " And attach it. Double tape. So first I think what I'm going to do is just lay this down. We can put the table down here. Just flip this. These sides. Do we need to measure the table? So where the type should be? We will attach it so that it is closer to this end. So I'm going to first start from here. And hold it. And can you already remove the trigger? Sure. You can just try to explain. Yeah. I think we can move the table outside for a little bit. Okay. Oh, it's two tables? okay so what about the other side? The other side can be a bit behind. It's okay. Okay. Mm-hmm. Just move it a bit forward. Yeah, and then it's also a little level on both ends. Yeah. Yeah. I think we push it in here. For the carpet. Okay." + }, + { + "category": "inspection_repair", + "name": "User_16_User_17_410_0511_1_480.mp4", + "transcript": " okay this room this table is labeled with damage and there's another label label says the damages the lag are not removed like this so we've adjust the height only one work so try to repair everything first let's put on the gloves okay i'll take this one it's not here first i think we should remove remove the cover the lower and upper let's first use the small remove the small bolt Thanks. and then remove the bigger bolts using the LMP No. okay remove the cover put them away and let's figure out where is that the problem is where is the handle the handle is over here just try it I think we should remove the bolt. Do you think we should remove the leg to check everything? I will try to remove this. You remove that board. That's what I'm moved. Hi. You can put the strings higher like this. More higher? So how should we check the frame? Let's just put it down. What's the problem with? Maybe with the lag, I think. Inside of the lag? Mm-hmm. So we need to separate these two. Okay. Is that able to do that? Okay, good. And lay it down. And remove the bolt behind. It's very tight. Oops, sorry. I think we can remove this part. Yes, I think so. why does that moving around maybe we if we just scoot in or scoot out if we scoot it in let it tighter compare with here this this should be very tight yes this is very tight let's try if that works yeah it works great so the problem is solved so let's screw them back in i think we have to first move the legs be careful okay Thank you. Make it tight. And also here, make it tight. As well as here. Oh, sorry. Okay, it's tight. Start around. And just screw them back in. Align the position. It's not aligned. It's weird. What if I'll turn one more around? Ah, yes. Is this in? Yeah. It seems like another hole. Disconnected them one more time. Something wrong. If there are two different holes. Okay. Yeah. Let's go to the downside. Yeah. It goes in. Great. OK. Very good. Now it's tight. Okay. No, no, no inside. Okay. So this is... Pull the tool back. Remove the battery. This is for at this part or should be at this part? This is empty. Turn it a little bit. Put the power cover back. And align the position. Now pull this bolt. I think align one side first. A little bit lower. Are you in? You can put in your first. Not so tight, just put them in a little bit. And then we can try to do that We should just... Let it in first. Yep. It's in? Okay. Where is that? My light. Good. We need this. Yeah, hold it. not so tight and then So I will lose the top one. Maybe they are too tight. You can lose a little bit. That's in. Good. I need one more. Where is it? You have one more? It's here, right here. push rumba push a little bit it's in? yeah so the damage part I think we can remove the label First." + }, + { + "category": "inspection_repair", + "name": "User_16_User_17_414_0511_3_480.mp4", + "transcript": " We need to move the table, make the table stable as possible. As we can see, it's shaking a lot. Let's figure out. I think we can just flip the table. One by one. this as well. Let's try to make them fast, make them tighter. make the legs as slow as possible and tighten all bolts Yep, better. Try this one. Hide this one also. Sorry. Hide it. Can we put it out? Remove them. Still moving. You can tighten them up. Much better. Still a little bit. Stick them in. much better let's check So this two parts are very... It's not on the ground? Right. Let me check. Can we just... Hold it. You can do it. Still not. The legs are moving. The whole legs are moving. It's not about the legs. Not really. Try it. Does it move? Much better. The table is still shaking. Yeah. So there are a little bit gap between the outside and inside bar. You can now screw in more tighter. Wrong way. Is that moving? Is the table moving? No? You can bring the level up or lower. Check it. We should lower this part a bit. Lower eye. for this part I think you should not move anything you just check this and move this like only Upper or lower? I'll try lower. Lower. No, no. Upper. Still higher. Still need to go a little bit higher. That's not very... Because it's loose, so I have to adjust the height. Okay, you can use your hand. Okay, can you just screw it in? Because I hold this. No, no, no, use this. Use this. Oh, this one? Yeah. That's right? Yeah. Okay. Okay. Hmm. This one? That's better. She can always... I think this is too high. Let me just remove everything. Maybe just loose them with this. And then you don't have to move. A little bit, a little bit. Loose it, loose it, loose it, loose. It's dropping. Check if that's inside. No. No. Why? Why? Why? Oh, my glove. It's not even inside. Here, here, here. Yeah, the bar is... This bar seems like shorter, right? No? No? Why is that so short? The other one just seems like very... It seems very short. So this is much. You can lose your hand. It doesn't need to. It's empty. And this is the maximum part. OK. Thank God. So just bolt it in. So weird. This is just so weird. Try it. it's the best we can do should we lower the height? no we should not lower the height Yeah, because... Let it do. I think I should lower this lower this so I will make this make this part shorter so if we use the extra length I think that's the most unstable If we let up each leg make the big surface on the ground, that won't be much stabilized. So I think let's try to lower a little bit. A little bit better. I think it's just lower this a little bit as well. You see? Yeah, there's a gap. No way to avoid the gap. So unless we have another hole. Or we have another this one to fit in there. We can just go find if there are any. Right? Each leg has the problem. So at least we know the problem. I just need to find another tool to fix it." + }, + { + "category": "inspection_repair", + "name": "User_16_User_17_0511_2_480.mp4", + "transcript": " OK, remove this table for the gloves. OK. Sorry, sorry. Amen. what we're going to do is remove the leg to adjust the height make the table higher so first we're going to use the allen key to remove the legs and adjust the height by unscrewing this I think we can do it at the same level Is that able to make it longer? This is the maximum at least it's the maximum level Yeah, it tastes very similar. So after, and then screw it back in. We have to leave one. Yeah, leave one of them. Because we have to compare these two with these. Hmm, what did I find? It's in that one? No, no, no. Is it the same thing? No, that's for these. Oh, you lose the under one. Okay. Oh, here. Okay. I think we can just slide them down. Oh. I'm going to adjust the height from this Yeah. You have to hold it very tight and I will push in. Let's see. with the holes inside. Wait a second. You cannot find it. And you can use, I'll tell you, you can just screw them out and screw them out. And to align the position, I will refine this. Don't move. And the last one You can put that there Just put them there. Where is this bolt? It's here. Find the bolt. Yeah, here. Okay. Okay. Okay. Okay. So if it's not aligned, we can just adjust this height, adjust this. If not leveled. It doesn't matter because it's just pretend to be moving. should be that there i think because here is a little bit Let's check. Yeah, the level is cool. Right in the middle, here. It's about in the middle, but here needs to be a little bit higher. Yes, here needs to be a little bit higher, so. Here need to be a little bit lower. I think lower, lower. It seems just there is a little bit too high. A little bit high, a little bit. Yeah, yeah, it's finished. I just have a try. It's fine. Fine. This one. Fine. I think... Higher, I think. Higher this part. Lower this part. Lower or higher? I think higher. Lower. Lower? more I think higher let me try higher this you see this is higher oh right sorry no no so there this one need to be higher perfect Perfect. Perfect. Perfect. Good. All right. Now we're finished." + }, + { + "category": "inspection_repair", + "name": "User_17_407_2910_1_480.mp4", + "transcript": " so we're going to change this frame because there's many parts loose and many are on the wrong position and this plate is off the frame so first we have to pull down the gloves And first we remove all these long rods and connectors. So we place the parts together. and there is this rule and there are still three of them and there are connectors and these two In the last one, there are still three connectors And last we have to remove this short row from this long one. And we have to remove this connector. so this will be the base and we'll put everything back together and first is this plate and we can see we should set some role here so the plate shouldn't block this part So here, the plate should be placed here. And there should be four connectors. the first place is small connectors to first move it to some place and then we align and check the detail this one is this one yep it's lined this one yep and the last one okay so we need to find four schools and let's find out what kind of schools we have so we have two types this long one and this short one and this long one of course is too long for this so we use this short one now we have certs really? Thank you. Bye. So we will find there are just two medium size and we will choose this through four So then tie it, tie the screws. These rules are not aligned. Let's loop it to the right. So there will be a long row here and two medium size here. And each with a short bolt. So we first will connect these two parts to the base. And we need some connectors here. And we need the small one. And we need to align these connectors and here. and we will place it somewhere here so we will align this connector And not too tight, we still have to line here in this place. The other connector is here. So it's the first part and the second part is here. And again, we have to align this connector 0 to 1, so we'll add one first. Approximately should be here. End line. Approximately the lens is... So move a little bit to the left. Yep, we'll do it here. So now we can fix it tight a little bit. and we need to connect these two short rows to this so we need a structure similar like similar like this and put the short row here so the first thing is these two medium row should be positioned by here It's too close now. And so we loose a little bit. And move it here. Right to the edge. And tighten. This side too. So first we need two long screws and fix this big connector to the road. first we will screw it with my hand no it's not this screw yep these two No. There should be a small connector here. so we first try to add the smoke nectar to this so then we add this here We need some small connectors first, otherwise we cannot really And this one. I'm going to start with this." + }, + { + "category": "inspection_repair", + "name": "User_17_410_0511_1_480.mp4", + "transcript": " so today we're going to fix this computing unit and there are already some labels missing RAM and defective so we'll check where the RAM is first so we first check for this part and remove the topper plate to see whether RAM is on the top Yep, so RAM is here, so we'll pick a RAM chip and see whether it is fitting. Yep, so the RAM is on. So we will test if this community unit start correctly. So we have to connect it to the monitor and plug in the power. So, let's turn on the monitor. And... So, the computer computer unit is on. Let's find out. So you can see we have successfully boosted into the system. The unit is now usable. We can remove the label and then put the top plate back. So first disconnect to the monitor and power off. And tie the screws. So we finished the task." + }, + { + "category": "inspection_repair", + "name": "User_17_411_2810_4_480.mp4", + "transcript": " Mm-hmm. So we first check. No, it doesn't start. First we have to remove the cover. yep the power cable is not connected the speed fan is also not connected hard disk should be here Let's remove this part and connect the hard disk. This part is missing. Yeah, so like this. So we need to find the screws for the hair And the battery, the battery is not. I had to remove this graphic card. It's blocked away to the memory chip. The screw is missing. cables here one for the c player one for the yeah all wrong this is one this part to this and this part to this hmm So we're missing... It's here. It's here. so insert the RAM chip This is still another cable. This is on the fan. The fan is not connected to the motherboard. It's a satellite. CD player and one for you. It's a power line and now it's a data line and this is a power line. It's not long enough We need to cut the zip tie to the side and then it's not long enough so we'll remove this part this short one and replace with a longer one so we'll tie this line together and put it here we use a led zipline to fix it here So we installed it back. So we will not install this. No, we don't have a grid here. So we just installed graphic card back. these are parts that we don't need for now and we can see if it's It's alright, so it's turn power on and the check of the stars. No. The power is not on. The fan is on. Let's check out the CD player. And... Yeah. So I think that's it. I have to move this part. So that's it." + }, + { + "category": "inspection_repair", + "name": "User_17_411_2810_5_480.mp4", + "transcript": " So, it's not fixed. It's a sideboard and Fan cable, this part cable. Two hard disks here. There are four. these are the power cable and this one yeah this one is also a power cable there is a bunch of The fan is here. Power lines are here. The SATA zone here. This is for this, this one is here. This one is here. We need another. This should be another one. Yeah, it's here. Mm-hmm. There's two rooms for the memory shift. But which disk should we use here? And perhaps we don't need these two. Perhaps we need one of these. And memory... So, still got the battery. and it's all this is all yep so yep we finished it and we tested the we tested these Yeah, we'll see if it boost. And the light is on. This view fan is the arrow. I have to find... It's here. So we start again. yep so this should be the right socket for the cpu file and we'll try again if there's an error so there is no error and then we finish the work so we'll power off the PC and disconnect the power cable and the cable to the monitor and remove the side plate to it Yep, it's over." + }, + { + "category": "inspection_repair", + "name": "User_17_412_1610_2_480.mp4", + "transcript": " so today we're going to install the graphic card to the pc and first we will use this trolley to move the pc and the graphic card to this room from the conference room So here's a graphic card and the PC we need. We'll first move the PC on the trolley. And the graphic card. Close the door. close the door and then we will turn on the lights so put the graphic card first on the table and the PC on the ground on this side we need some screwdriver so here is the screwdriver first we remove these two screws put it here and remove the cover slide a little bit and move it we have to first uninstall the spar plate arm plate to uninstall this screw here and remove this plate and here is the graphic card we have to first remove these screws and install the graphic card on this side so there's not enough play space for the graphic card not enough space so we remove this wire first still So, remove this card here. Yep, now we have enough space for the graphic card. And we will insert it to the socket. No, it's not removed. and we will install the screws back Yep, silver is tight. Next we'll reinstall this plate back in the box. now we install the wrong scroll here this is for here Tie the screws and pull the cover back. push back and install these two screws it's tight so here's the part we uninstalled from the PC so we finish the task and pull these components back on the table and screwdrivers back here So we're finished the task." + }, + { + "category": "inspection_repair", + "name": "User_17_412_2310_4_480.mp4", + "transcript": " so today we are going to check about this PC and see if it's missing some part or have any other issues and finally we will test if this PC start normally so first we will remove this side plate so here we have to use the screwdrivers to untie these two screws here and slide a bit and we can remove the side plate and we can put it here first so next we have to move this plate we can have a better view the screws is out and yep we can play the plate here with the screw so we're going to check about the PC and we find some unattached cable and there's no RAM chip here and here this part is also empty and there are some cables here unattached and the battery on the motherboard is still missing and there are some cutted tie zips so we can put them aside and yeah that's a that's all the things we can check for now so first we will try to remove the graphic card because it's blocking the way for us to install the memory card memory chips there's still missing one screws here so there's a lock here for the graphic card so you can simply pull the graphic card out and put it here and another cable here but it is not attached to anything so first we will will remove this cable and put it aside so the screwdrivers for this part the back end will put it here so first we'll find the other yeah the missing part probably all here we can see there are hard disk and the CD player and all sort of stuff here so we will try to put down this part first put the screws together so we will not miss them and this part we need some Allen wrench using this part fix, nope some other part these two yep effects and screw them down and this Yep. Yep. So this part is out. This is the place for the CD player. And also we have to remove this part. And here's a place where we can install the hard drive, hard disk. pull the screws together and these two small screws So this part is also out. Put it here first. So we'll check if there's other things wrong with the PC and yeah. So we first we have to install the battery to the motherboard. Yeah, if we hear a click and it's on. And there's others. Yeah, we have some, we have a disk. and there are there's still one school is missing and the school is here so we have all the schools we put it here first and we check there are two memory chips and we have to install it before the graphic card so we'll pull the lock aside and push it a bit and then here's the click yep and we will pull we'll install the other memory card to the same color to the socket that was the same color so find the place and push a bit yep we'll hear the click and it's on so now we're going to install the hard disk to the frame of this so here nope we have to move this part out first yep we uninstall this out so the hard drive is here and yep we will install the hard drive here so we should find the right screw for this That's not the right one. Yeah, this is one. or school driver. yep so we tied the screws a bit and we will install it back and make sure it is We should align it first. No, so it's not the right position. So we have to take it back. So it should be like this. yeah this should be right so the disk should be on this side and here so remember the position and for the second side we will install this First, let's try we can really install the cable to it. Yeah, it's working, so it's not blocking. Now we will install the screws to here. Reflect it over. Align. On the other side. so this part is alright and we will install the CD player to this frame and it should be So now we first align and Yep. and there is still flip it over one left and we're trying to get it back No, it's not the right position. That should be. yep that's the place so it's here here so if we install this part first And we will plug the power line, power cable of the disk. and the data cable The guy can help you with that. It's hard to see where the cable is. So we don't need a connection here. We need a connection here. I don't need that hard disk and this and this will, yup and the other side We have to add this port. That's not necessary at the moment. Yeah, okay. Because it will be quite late. Okay, and... I think we can just test if it is actually connected. Yeah. Yep. I said... I can just install this. Install this. Yep, so. The power cable is... yes yeah this part works okay and for the others these are taken apart and yeah but the repair work was successful yeah i think um Here, I'm lost on time here, because..." + }, + { + "category": "inspection_repair", + "name": "User_17_451_2201_1_480.mp4", + "transcript": " Thank you. so today we're going to check about this pc so first we can connect to the power and to check if the pc starts normally and here's the cable this one doesn't work yep so the PC doesn't work doesn't start so first we disconnect the cable and open it and check whether the components are correctly installed and we get some tools and parts perhaps we can use them so first is we have to check about the power unit cable so here is connect but here is not so first we have to connect this and next one we have to check about the simos so the battery is gone so next we need to check the RAM and CPU fan is also missing so we will first here this is CPU fan and we have to install it on the motherboard and this is the power cable for the fan so here is a fan for the CPU so yep so now we can tie the screws And it has to also connect the power cable. next step is for the ram so here we go to ram chip and we can install them Now we can install them both on the wide sockets. so next though there's still hard disk missing in this place so we can install hard disk into the slot and here's a click and so the hard disk is on so we need to also connect it to the power cable and also the data cable so here this cable is on it's connected to the motherboard so we can connect the tables to the hard disk and also hard and no data cable and here's also cables that not connected we can see on the motherboard here are two slots and one is here so we connect this from here and we have another two cables this one and this one yup so the cables are here to this socket And this one to this socket. so so now we will check again for the cables this two this one this one this two these two so now we can check if it's working So here is our power cable. We connect to the PC again. So this time it works. No. Yup. so check again and see if this city room works ok yep so now we can connect the PC to the monitor and see whether it really boosts into the system so here's our monitor cable before we testing that we should clean a little bit and close the carpet so we had to cut off the power and check if there is something like here It's all right. So now we can connect the cable again into, yep so we can see the PC successfully boosted into the system Yep, so that means this PC works for now. So we can close the PC and the task is finished." + }, + { + "category": "inspection_repair", + "name": "User_17_451_2201_2_480.mp4", + "transcript": " so today we're going to check and repair this PC so we can first we can see this city room is not correctly installed it's not fixed and perhaps there are other problems so first we can check a bit connect the PC with power cable and let's see if it starts normally nope it doesn't start so disconnect the power and we can open this PC and check inside first we should check out the power unit you can see this this cable is connected but this cable is not so we have to connect to this socket and another one we have to check out the CPU fan the CPU fan is not installed so here we got the fan so we need to put it on and also connect the power cable so we need to tighten the screws yep and also the power cable should be here it's a little bit dark so now the CPU fan is on and here the battery, the simos battery is missing so we can put the battery on and also the RAM chips it's not correctly installed and we need another one here so we can now install them to the wide socket so the next step we have to check out the hard disk so here this one this one is not connected to the motherboard and this one is also not fixed in this place so We need another hardest case for it. And also this one. so this one this one is good seems a little bit too big for this case i can change for another and now we can put the hard disk into these two slots and also we got an SSD here so we can also put it here but it could not fix the slot so we just put it in there but before that we had to connect the data cable and the power cable and also we need to connect this hard disk with the motherboard so this is a power cable and also the data cable there is one Yup, there's two. This one and this one. yup so this SSD and these two hard disks are all connected to the motherboard and last we will check about this CD drive so the first thing is we need to fix this to the PC case easier yup there are two screws and we have to Fix these two. Thank you. Is there a chance we're going to remove this one? Thank you. so now the serial driver is connected to the PC case and the power cable and data cable are not connected Install the data cable. This one is not long enough. So now we connect all the cables and all the components are connected. Let's chat for that other time. so now we can test a little bit we can connect to the power cable and check yep it works so the PC now is running and we need to check if it could successfully boot into the system so close it yep we need to check if there is something else we can clean it's alright so we will close the sideboard the power cable and also the VGA cable so let's see if the PC can post into the system so now we can see it's loading yep so now we can see the windows so the PC now can successfully run in and we can now close it so that means we finish the task disconnect all the cables So that's you." + }, + { + "category": "inspection_repair", + "name": "User_17_User_1_407_2910_1_480.mp4", + "transcript": " I don't know if this is aligned or not because this is not fit completely we need one more okay yeah it's here so fit like this so Now it's... Now first let's use this one. It should be, yeah. Yep, yep, here. Yep, that's where I can place. Yep, so. It's just for positioning. Yeah, okay. then this one here still one left these two three so that one maybe is unnecessary Yep, so that's it." + }, + { + "category": "inspection_repair", + "name": "User_17_User_16_410_0511_1_480.mp4", + "transcript": " only this part can go higher and this part doesn't move Use the small, remove the... So I can pull it out. No, no, no, there's still one out. So we can get it out. Cover. Oh, no. And let's figure out where is that the problem is. Where's the handle? The handle is the only thing. Let's try with this one. So this part, let's move. To remove these two. So we have to use a trailer. Yeah, let's just, at first, remove these two, and... Yeah. Let's do a tie. Is the strength higher? No. Still no. Yep. Okay. So how should we... Let's just put it down and... What's the problem with... Maybe with the lag, I think. Inside of the lag? Mm-hmm. So we just separate these two together. Yeah. Okay. No, this one doesn't fit. No, this one doesn't fit. I mean, you can only... Is it because of this? Yeah, I think so. So we can use the handle again. Watch your fingers. Yeah, it works. Where's the other L? And also here, making tight. It's not lying. It's weird. What about turn one more along? Yeah. Is this it? Yeah. It seems like another hole. Is there a tree? Or we have to lower it to the downside. It's a little bit tight here. Great. So we still need the screws. Do we post this somewhere? Under the lag? Here. No, no. So this is for at this part or it should be at this part? Yeah, okay. Yeah. Yeah, one side first. Here. I don't know. turning these this one not so tight Now we can try to make it. No, not on this side. Yeah, it's on. It's on the right side. You need this. Small one. I need a little bit of sprints in the middle. Watch your fingers. I will lose the top of the top one because they are too tight. You can lose a little bit. Yeah. It's under the light. Yeah, it's down the line. Can you push a little bit? Yep, yep, yep. Yep. Tie. Okay." + }, + { + "category": "inspection_repair", + "name": "User_17_User_16_414_0511_3_480.mp4", + "transcript": " Thank you. This one is not fixed. Yeah, mine is here. Yeah, but this part, we need one of these plastic stuff here. Can we put it now? No, no, it's too tight. We have to remove them first. Yeah, okay. And stick. No, no, my gloves. Okay, yeah. All right, still moving. Let's hide them out. Yep, this time is fixed. Now flip it over and... No, it's still not stable. Again, it's not on the ground. Yeah, we have to tweak this, the plate under the leg. Yep. Yep, so let's put it down first. It's more stable. Yeah, that part is not on the ground. So I will lift it up for you. Does it move? Yeah. Yeah. So the problem could be the uppers. Oh. Yeah. Yeah. Yeah, but we should lower this part a bit. Just lower this part higher than that part. Yeah. It's. no no upper upper still higher still need to go a bit higher that's not very No, just move the downside to the plate. Because it's loose. Ah, okay, okay. Yeah, doesn't move. Doesn't really move. You can close your hand? Yeah. No, no, no. Where's the screwdriver? Yeah, yeah. We should figure it out. It's shaking to which direction in this direction or. Yeah, no. This should be higher. No, it's too low. Maybe just lose them with this. Really? Okay. You don't have to move. Yeah. It fell. Yep. Yeah, let's see. And where is it? Yeah. You have to lift it up first. Why? Why? Oh, my glove. It's not in the inside. Here, here, here. I know. Yeah, you know, you made the whole drawing. Yeah, the bar is... This bar seems like shorter, right? What? No? No? I don't know. Why is it so short? The other one, just to see. Hmm. Alright, see? Yeah, yeah, yeah, I know. Yeah, I know. This is the maximum part. Thank God. Just bolt it in. Same way. This is just so weird. We can't even adjust this part. What happened? This part is not fixed. Now we should do without class. no because it just doesn't reach the ground the problem is this part doesn't really move Yeah. Yeah, yeah, I know. There's a gap. Yeah, there's a gap. No way to avoid the gap. So unless we have... Yeah, yeah. It's plastic stuff. Or we have another list one. Yeah. Yeah. We can just go find... Yeah. Yeah. So that's it. That's it." + }, + { + "category": "inspection_repair", + "name": "User_17_User_16_0511_2_480.mp4", + "transcript": " Sorry, stop. So first I'm tight here. the same height around the same level a little bit tight I'm saying is this high enough at this level? Yeah, okay. Let's check again. Yeah. I have to first throw it back. We have to leave one. Yeah. Yeah. Because we have to compare these two with these. I put a screw here. And where is it? No, no, no. No, that's for these. And can you find the others? Ah, here, here. Let's put them aside. Okay. so this is the standard lens And if it's fixed, then test here. We have to first fix this. This should be the same. Almost. We have to push it back. You have to hold it very tight. Okay. So we have to install this back. How can it align with a hole? It's a little bit dark. Don't move. Yeah, okay. This one's here. Well, there's another. So I just put it on both sides. Just put it on there. Just a little bit later. Can you? Where is this bolt? Here. It's a line, right? Okay, it's time. And do... So if it's not aligned, we can just adjust this height. Ah, okay. Should this plastic part in the... Yeah. Oh, yeah, yeah. There's the bolts. Yep. so the level is cool right in the middle here it's about in the middle but here needs to be a little bit higher and here needs to be a little bit higher so yeah in this part Here need to be a little bit lower. Lower. Lower. Lower. Just put the door to this bit. I can hold it, I can hold it. I can, yeah. Oh, okay. Yeah. Yeah. Should lower this part a little bit. Higher, I think. Higher. Lower this part. Lower or higher? I think it's higher. Lower, lower. I think it's lower. Yeah. More, a little bit more. I think higher. I think higher. You see, this is higher. Yeah. No, no. Yeah. A little bit. Yeah." + } + ] \ No newline at end of file